Fabrication and structural analysis of ZnO coated fiber optic phase modulators

Fiber optic modulators were fabricated by coating optical fibers with electrode and piezoelectric ZnO layers. The techniques of piezoelectric fiber optic modulator (PFOM) fabrication are presented, and the microstructure and crystallographic texture of the coatings are analyzed. In order to produce thick (approximately 5 μm) ZnO coatings, it was necessary to study the reactive dc magnetron sputtering process in O2/Ar gas mixtures under conditions close to the transition between an oxidized and nonoxidized Zn target surface. In situ quartz crystal microbalance measurements of the deposition rate revealed thee distinct regions in the deposition rate (R) vs oxygen partial pressure behavior, at constant total pressure, for sputtering under conditions that provided an oxidized Zn target surface. Additionally, a transition between oxygen and argon dominated sputtering as observed by varying the sputtering pressure while maintaining a constant The transition between oxygen and argon dominated sputtering influences R to varying extents within the three R vs regions for an oxidized target surface. Correlations among the cathode current and voltage, deposition rate, and gas flow rate are presented to give a better understanding of the reactive sputtering processes occurring at the oxidized Zn target surface. Sputtering conditions optimized for a high ZnO deposition rate were used to produce 〈001〉 radially oriented ZnO fiber coatings for PFOM devices that can produce optical phase shifts as large as 0.38 rad/

The impact of seismic noise produced by wind turbines on seismic borehole measurements

Seismic signals produced by wind turbines can have an adverse effect on seismological measurements up to distances of several kilometres. Based on numerical simulations of the emitted seismic wave field, we study the effectivity of seismic borehole installations as a way to reduce the incoming noise. We analyse the signal amplitude as a function of sensor depth and investigate effects of seismic velocities, damping parameters and geological layering in the subsurface. Our numerical approach is validated by real data from borehole installations affected by wind turbines. We demonstrate that a seismic borehole installation with an adequate depth can effectively reduce the impact of seismic noise from wind turbines in comparison to surface installations. Therefore, placing the seismometer at greater depth represents a potentially effective measure to improve or retain the quality of the recordings at a seismic station. However, the advantages of the borehole decrease significantly with increasing signal wavelength.</p

Fabrication and structural analysis of ZnO coated fiber optic phase modulators

Fiber optic modulators were fabricated by coating optical fibers with electrode and piezoelectric ZnO layers. The techniques of piezoelectric fiber optic modulator (PFOM) fabrication are presented, and the microstructure and crystallographic texture of the coatings are analyzed, Ln order to produce thick (approximately 5 mu m) ZnO coatings, it was necessary to study the reactive de magnetron sputtering process in O-2/Ar gas mixtures under conditions close to the transition between an oxidized and nonoxidized Zn target surface. In situ quartz crystal microbalance measurements of the deposition rate revealed thee distinct regions in the deposition rate (R) vs oxygen partial pressure (P-o2) behavior, at constant total pressure, for sputtering under conditions that provided an oxidized Zn target surface. Additionally, a transition between oxygen and argon dominated sputtering as observed by varying the sputtering pressure while maintaining a constant P-o2. The transition between oxygen and argon dominated sputtering influences R to varying extents within the three R vs P-o2 regions for an oxidized target surface. Correlations among the cathode current and voltage, deposition rate, and gas flow rate are presented to give a better understanding of the reactive sputtering processes occurring at the oxidized Zn target surface. Sputtering conditions optimized for a high ZnO deposition rate were used to produce [001] radially oriented ZnO fiber coatings for PFOM devices that can produce optical phase shifts as large as 0.38 rad/V

Composição dos óleos essenciais de variedades de coloração de frutos de Eugenia brasiliensis Lam.

A espécie Eugenia brasiliensis Lam. apresenta a coloração dos frutos variável, sendo reconhecidas três variedades. Entretanto, a definição de variedades não é fácil para espécies de Myrtaceae e também não é amplamente aceita. Duas variedades de Eugenia brasiliensis, baseado na cor dos frutos (roxos e amarelos), tiveram a composição de seus óleos essenciais analisadas com a finalidade de obter indícios de variedade botânica para esta espécie. Embora, os componentes principais nos óleos das folhas fossem os mesmos monoterpenos para ambas as variedades, alfa-pineno, beta-pineno e 1,8-cineol, a variedade com frutos roxos acumulou maior quantidade de sesquiterpenos oxigenados (33,9%) do que aquela com frutos amarelos (3,8%). As diferenças principais ocorreram nos frutos roxos que apresentaram como componente principal o óxido de cariofileno (22,2%) e o alfa-cadinol (10,4%), não detectados no óleo das folhas, e o óleo dos frutos amarelos apresentou uma composição similar àquela observada para as folhas. Estas variedades de coloração dos frutos de E. brasilensis podem ser considerados como dois quimiotipos distintos, uma vez que na variedade com frutos roxos a rota biossintética para sesquiterpenos encontra-se mais operante do que naquela com frutos amarelos, onde são acumulados principalmente os monoterpenos.Eugenia brasiliensis Lam. is a variable species concerning fruit colour, with three recognized varieties. However, the definition of varieties is not easy for Myrtaceae species and not widely accepted. Two fruit colour varieties (purple and yellow) of E. brasiliensis had their essential oil composition analysed in order to give support to the existence of varieties for this species. Although, the major components in the leaf oil are the same monoterpenes for both varieties, alpha-pinene, beta-pinene and 1,8-cineol, the purple fruit variety accumulates more oxygenated sesquiterpenes (33.9%) than the one with yellow fruits (3.8%). The major differences occurred in purple fruits that present as major components caryophyllene oxide (22.2%) and alpha-cadinol (10.4%), not found in the leaf oil, and the yellow fruit oil presented a similar composition as observed for the leaves. These fruit colour varieties of E. brasilensis can be considered as two distinct chemotypes, since the sesquiterpene pathway is more operant in the purple variety than in the yellow one, in which monoterpenes are mainly accumulated

In situ strain and temperature monitoring of adaptive composite material

An optical fiber sensor is designed to simultaneously measure strain and temperature in an adaptive composite material. The sensor is formed by splicing two fiber Bragg gratings (FBGs) close to each other, which are written in optical fibers with different core dopants and concentrations. Their temperature sensitivities are hence different. The sensor is tested on an adaptive composite laminate made of unidirectional Kevlar-epoxy prepreg plies. Several 150 μm diameter prestrained NiTiCu shape memory alloy (SMA) wires are embedded in the composite laminate together with one fiber sensor. Simultaneous monitoring of strain and temperature during the curing process and activation in an oven is demonstrate

Photoelasticity of crystalline and amorphous silica from first principles

Based on density-functional perturbation theory we have computed from first principles the photoelastic tensor of few crystalline phases of silica at normal conditions and high pressure (quartz, $\alpha$-cristobalite, $\beta$-cristobalite) and of models of amorphous silica (containig up to 162 atoms), obtained by quenching from the melt in combined classical and Car-Parrinello molecular dynamics simulations. The computational framework has also been checked on the photoelastic tensor of crystalline silicon and MgO as prototypes of covalent and ionic systems. The agreement with available experimental data is good. A phenomenological model suitable to describe the photoelastic properties of different silica polymorphs is devised by fitting on the ab-initio data.Comment: ten figure

Initial Characterization of the FlgE Hook High Molecular Weight Complex of

The spirochete periplasmic flagellum has many unique attributes. One unusual characteristic is the flagellar hook. This structure serves as a universal joint coupling rotation of the membrane-bound motor to the flagellar filament. The hook is comprised of about 120 FlgE monomers, and in most bacteria these structures readily dissociate to monomers (∼ 50 kDa) when treated with heat and detergent. However, in spirochetes the FlgE monomers form a large mass of over 250 kDa [referred to as a high molecular weight complex (HMWC)] that is stable to these and other denaturing conditions. In this communication, we examined specific aspects with respect to the formation and structure of this complex. We found that the Lyme disease spirochete Borrelia burgdorferi synthesized the HMWC throughout the in vitro growth cycle, and also in vivo when implanted in dialysis membrane chambers in rats. The HMWC was stable to formic acid, which supports the concept that the stability of the HMWC is dependent on covalent cross-linking of individual FlgE subunits. Mass spectrometry analysis of the HMWC from both wild type periplasmic flagella and polyhooks from a newly constructed ΔfliK mutant indicated that other proteins besides FlgE were not covalently joined to the complex, and that FlgE was the sole component of the complex. In addition, mass spectrometry analysis also indicated that the HMWC was composed of a polymer of the FlgE protein with both the N- and C-terminal regions remaining intact. These initial studies set the stage for a detailed characterization of the HMWC. Covalent cross-linking of FlgE with the accompanying formation of the HMWC we propose strengthens the hook structure for optimal spirochete motility