816 research outputs found
Distribution of parallel vortices studied by spin-polarized neutron reflectivity and magnetization
We present the studies of non-uniformly distributed vortices in Nb/Al
multilayers at applied field near parallel to film surface by using
spin-polarized neutron reflectivity (SPNR) and DC magnetization measurements.
We have observed peaks above the lower critical field, Hc1, in the M-H curves
from the multilayers.
Previous works with a model calculation of minimizing Gibbs free energy have
suggested that the peaks could be ascribed to vortex line transitions for
spatial commensuration in a thin film superconductor. In order to directly
determine the distribution of vortices, we performed SPNR measurements on the
multilayer and found that the distribution and density of vortices are
different at ascending and descending fields. At ascending 2000 Oe which is
just below the first peak in the M-H curve, SPNR shows that vortices are mostly
localized near a middle line of the film meanwhile the vortices are distributed
in broader region at the descending 2000 Oe. That is related to the observation
of more vortices trapped at the descending field. As the applied field is
sightly tilted (< 3.5degree), we observe another peak at a smaller field. The
peak position is consistent with the parallel lower critical field (Hc1||). We
discuss that the vortices run along the applied field below Hc1|| and rotate
parallel to the surface at Hc1||.Comment: 17 pages, 9 figure
Experimental study on a metal hydride based hydrogen compressor
This is the post-print version of the final paper published in Journal of Alloys and Compounds. The published article is available from the link below. Changes resulting from the publishing process, such as peer review, editing, corrections, structural formatting, and other quality control mechanisms may not be reflected in this document. Changes may have been made to this work since it was submitted for publication. Copyright @ 2008 Elsevier B.V.A three-stage metal hydride based hydrogen compressor prototype was built. It has been designed for a hydrogen production facility using a low-pressure alkaline electrolyser. The compression system should transfer heat recovered from the electrolyser into the hydride beds to allow hydrogen desorption flow. The three-stage compressor achieves a compression ratio of 20:1 atm. It performs a thermal cycling of three AB5 hydrides between 20 and 80 °C. Its flow rate, for 25 g of each hydride bed, reaches about 20 l (NTP) of hydrogen per hour. The prototype is now operational. Some improvements in the heat transfer management system are also carried out before proceeding to the interconnection with the electrolyser and to the extent that the hydrogen produced satisfies the high purity requirement of the hydrides used in the compressor.Natural Resources Canada(NRCan), Ministère des Ressources Naturelles
et de la Faune du Québec (MRNF), and Natural Sciences and Engineering Research Council of Canada
Performance of one-dimensional hydrodynamic lake models during short-term extreme weather events
Numerical lake models are useful tools to study hydrodynamics in lakes, and are increasingly applied to extreme weather events. However, little is known about the accuracy of such models during these short-term events. We used high-frequency data from three lakes to test the performance of three one-dimensional (1D) hydrodynamic models (Simstrat, GOTM, GLM) during storms and heatwaves. Models reproduced the overall direction and magnitude of changes during the extreme events, with accurate timing and little bias. Changes in volume-averaged and surface temperatures and Schmidt stability were simulated more accurately than changes in bottom temperature, maximum buoyancy frequency, or mixed layer depth. However, in most cases the model error was higher (30-100%) during extreme events compared to reference periods. As a consequence, while 1D lake models can be used to study effects of extreme weather events, the increased uncertainty in the simulations should be taken into account when interpreting results
Growth of (110) Diamond using pure Dicarbon
We use a density-functional based tight-binding method to study diamond
growth steps by depositing dicarbon species onto a hydrogen-free diamond (110)
surface. Subsequent C_2 molecules are deposited on an initially clean surface,
in the vicinity of a growing adsorbate cluster, and finally, near vacancies
just before completion of a full new monolayer. The preferred growth stages
arise from C_2n clusters in near ideal lattice positions forming zigzag chains
running along the [-110] direction parallel to the surface. The adsorption
energies are consistently exothermic by 8--10 eV per C_2, depending on the size
of the cluster. The deposition barriers for these processes are in the range of
0.0--0.6 eV. For deposition sites above C_2n clusters the adsorption energies
are smaller by 3 eV, but diffusion to more stable positions is feasible. We
also perform simulations of the diffusion of C_2 molecules on the surface in
the vicinity of existing adsorbate clusters using an augmented Lagrangian
penalty method. We find migration barriers in excess of 3 eV on the clean
surface, and 0.6--1.0 eV on top of graphene-like adsorbates. The barrier
heights and pathways indicate that the growth from gaseous dicarbons proceeds
either by direct adsorption onto clean sites or after migration on top of the
existing C_2n chains.Comment: 8 Pages, 7 figure
IHTC14-23079 TRANSPORT PROCESS STUDY IN SODIUM ALANATE HYDROGEN STORAGE SYSTEM DURING DESORPTION
ABSTRACT Transport processes in a sodium alanate hydrogen storage system during desorption are presented. The mathematical model, which considers heat conduction and convection, hydrogen flow governed by Blake-Kozeny law and the chemical kinetics, is solved using the COMSOL Multiphysics ® finite element software. The numerical simulation is used to present the time-space evolutions of the temperature, pressure and hydride concentration. The results are discussed for two cases: a finned storage system and a finless one. It is shown that the whole process occurring in the bed is governed and controlled by heat transfer from the heating fluid to the storage media and strengthened by axial heat transfer through the fins. The importance of the hydride bed thermal conductivity has also been evaluated. It was observed that the hydrogen discharge rate in a finless system can be improved if we find ways of increasing the thermal conductivity of the storage media. On the other hand, for a reservoir with fins, heat transfer is good enough that the discharge rate is limited by the kinetics
Recommended from our members
Ulcerative colitis-risk loci on chromosomes 1p36 and 12q15 found by genome-wide association study.
Ulcerative colitis is a chronic inflammatory disease of the colon that presents as diarrhea and gastrointestinal bleeding. We performed a genome-wide association study using DNA samples from 1,052 individuals with ulcerative colitis and preexisting data from 2,571 controls, all of European ancestry. In an analysis that controlled for gender and population structure, ulcerative colitis loci attaining genome-wide significance and subsequent replication in two independent populations were identified on chromosomes 1p36 (rs6426833, combined P = 5.1 x 10(-13), combined odds ratio OR = 0.73) and 12q15 (rs1558744, combined P = 2.5 x 10(-12), combined OR = 1.35). In addition, combined genome-wide significant evidence for association was found in a region spanning BTNL2 to HLA-DQB1 on chromosome 6p21 (rs2395185, combined P = 1.0 x 10(-16), combined OR = 0.66) and at the IL23R locus on chromosome 1p31 (rs11209026, combined P = 1.3 x 10(-8), combined OR = 0.56; rs10889677, combined P = 1.3 x 10(-8), combined OR = 1.29)
- …