Algorithm based comparison between the integral method and harmonic analysis of the timing jitter of diode-based and solid-state pulsed laser sources

AbstractA comparison between two methods of timing jitter calculation is presented. The integral method utilizes spectral area of the single side-band (SSB) phase noise spectrum to calculate root mean square (rms) timing jitter. In contrast the harmonic analysis exploits the uppermost noise power in high harmonics to retrieve timing fluctuation. The results obtained show that a consistent timing jitter of 1.2ps is found by the integral method and harmonic analysis in gain-switched laser diodes with an external cavity scheme. A comparison of the two approaches in noise measurement of a diode-pumped Yb:KY(WO4)2 passively mode-locked laser is also shown in which both techniques give 2ps rms timing jitter

Research and investigation of geology, mineral, and water resources of Maryland

The authors have identified the following significant results. Field work in Baltimore County revealed that the signature returns of serpentinitic and nonserpentinitic rocks correlates with the vegetation cover and land use pattern. In Maryland Piedmont, bedrock lithology and structure are enhanced only to the extent that land use is geologically dictated. Two prominent sets of linear features are detected on ERTS-1 imagery at N 45 deg E and N 20 deg E. Beaches of Chesapeake Bay are classified as broad and narrow beaches based on the width of the backshore zone. It is shown by comparing historical shorelines of Ocean City, from the inlet to the Maryland-Delaware line that reversal zones of erosion and accretion occur at different locations for different periods. High reflectance levels (high marsh-high topographic areas) for the lower Eastern Shore are found to be distributed as two distinct trending linear ridge systems. Observations of MSS band 5 dated 9 April 1974 exhibited an unique sedimentation pattern for Chesapeake Bay. Following a 1.5 inch rainfall, heavy concentration of suspended sediments is observed on the imagery, particularly in the area of the turbidity maximum

EVALUATION OF A TURBIDITY METER FOR USE AT THE DEFENSE WASTE PROCESSING FACILITY

Savannah River Remediation's (SRR's) Defense Waste Processing Facility (DWPF) Laboratory currently tests for sludge carry-over into the Recycle Collection Tank (RCT) by evaluating the iron concentration in the Slurry Mix Evaporator Condensate Tank (SMECT) and relating this iron concentration to the amount of sludge solids present. A new method was proposed for detecting the amount of sludge in the SMECT that involves the use of an Optek turbidity sensor. Waste Services Laboratory (WSL) personnel conducted testing on two of these units following a test plan developed by Waste Solidification Engineering (WSE). Both Optek units (SN64217 and SN65164) use sensor model AF16-N and signal converter model series C4000. The sensor body of each unit was modified to hold a standard DWPF 12 cc sample vial, also known as a ''peanut'' vial. The purpose of this testing was to evaluate the use of this model of turbidity sensor, or meter, to provide a measurement of the sludge solids present in the SMECT based upon samples from that tank. During discussions of the results from this study by WSE, WSL, and Savannah River National Laboratory (SRNL) personnel, an upper limit on the acceptable level of solids in SMECT samples was set at 0.14 wt%. A ''go/no-go'' decision criterion was to be developed for the critical turbidity response, which is expressed in concentration units (CUs), for each Optek unit based upon the 0.14 wt% solids value. An acceptable or a ''go'' decision for the SMECT should reflect the situation that there is an identified risk (e.g. 5%) for a CU response from the Optek unit to be less than the critical CU value when the solids content of the SMECT is actually 0.14 wt% or greater, while a ''no-go'' determination (i.e., an Optek CU response above the critical CU value, a conservative decision relative to risk) would lead to additional evaluations of the SMECT to better quantify the possible solids content of the tank. A sludge simulant was used to develop standards for testing both Optek units and to determine the viability of a ''go/no-go'' CU response for each of the units. Statistical methods were used by SRNL to develop the critical CU value for the ''go/no-go'' decision for these standards for each Optek unit. Since only one sludge simulant was available for this testing, the sensitivity of these results to other simulants and to actual sludge material is not known. However, limited testing with samples from the actual DWPF process (both SRAT product samples and SMECT samples) demonstrated that the use of the ''go/no-go'' criteria developed from the sludge simulant testing was conservative for these samples taken from Sludge Batch 7b (SB7b), the sludge batch currently being processed. While both of the Optek units performed very reliably during this testing, there were statistically significant differences (although small on a practical scale) between the two units. Thus, testing should be conducted on any new unit of this Optek model to qualify it before it is used to support the DWPF operation

Beebots-a-lula, Where's My Honey?: Design Fictions and Beekeeping

The honey bee is a powerful cultural motif that remains an important symbol for the future. Their role as pollinators, alongside a myriad of other species, is critical to the continued diets of humankind. This Future Scenario explores a possible near future where human intervention poses new risks to their survival. Drawing on folklore and contemporary beekeeping practices, Mr Shore's Downfall tells a tale of discovery and loss as a young beekeeper is introduced to the world of honey bees. Three imagined artefacts are revealed through the story and discussed with consideration of their cultural context, desirability and relation to socio-economic factors. Themes from Mr Shore's Downfall are examined, and the potential of writing practice for design fiction practitioners is considered

Tracing Slow Winds from T Tauri Stars via Low Velocity Forbidden Line Emission

Using Keck/HIRES spectra {\Delta}v ~ 7 km/s, we analyze forbidden lines of [O I] 6300 {\AA}, [O I] 5577 {\AA} and [S II] 6731 {\AA} from 33 T Tauri stars covering a range of disk evolutionary stages. After removing a high velocity component (HVC) associated with microjets, we study the properties of the low velocity component (LVC). The LVC can be attributed to slow disk winds that could be magnetically (MHD) or thermally (photoevaporative) driven. Both of these winds play an important role in the evolution and dispersal of protoplanetary material. LVC emission is seen in all 30 stars with detected [O I] but only in 2 out of eight with detected [S II] , so our analysis is largely based on the properties of the [O I] LVC. The LVC itself is resolved into broad (BC) and narrow (NC) kinematic components. Both components are found over a wide range of accretion rates and their luminosity is correlated with the accretion luminosity, but the NC is proportionately stronger than the BC in transition disks. The FWHM of both the BC and NC correlates with disk inclination, consistent with Keplerian broadening from radii of 0.05 to 0.5 AU and 0.5 to 5 AU, respectively. The velocity centroids of the BC suggest formation in an MHD disk wind, with the largest blueshifts found in sources with closer to face-on orientations. The velocity centroids of the NC however, show no dependence on disk inclination. The origin of this component is less clear and the evidence for photoevaporation is not conclusive