3,364 research outputs found

    Pull-out strength of axially loaded steel rods bonded in glulam perpendicular to the grain

    Get PDF
    A total of 86 pull-out strength tests on glued-in steel rods with metric threads M12, M16 and M20 are reported in this paper. The rods were bonded in glulam made of Norway spruce lamellas perpendicular to the grain by means of an epoxy-type adhesive using the GSAÂź-system. The slenderness ratios of the rods λ calculated from the anchoring lengths ℓ with respect to the diameter of the drill hole d h (λ=ℓ/d h) varied between 7.5 and 12.5. Registered failure loads were considerably higher than design values derived from different existing approaches. The pull-out strength was found to be almost directly proportional to the surface area of the bond line. Based on this an approach to estimate the pull-out strength is suggested. Dependence between pull-out strength and anchoring length ℓ as well as slenderness ratio λ exists, whereas such dependence for the diameter of the rod was not found. The pull-out strength is influenced by the wood density. Compared to rods bonded in parallel to the grain, pull-out strength of rods with same diameter and anchoring length set perpendicular to the grain are 20-50% highe

    Pull-out strength of axially loaded steel rods bonded in glulam parallel to the grain

    Get PDF
    Bonded-in steel rods are very efficient in withstanding high forces applied to timber members. Investigations of bonded-in rods started in the late eighties of the last century and several design models were published since. By comparing these approaches on base of an extensive literature review a certain degree of discrepancy and partly even contradiction can be found. The paper describes a test program which aimed to study the influence of timber density and of geometric parameters on the pull-out strength of single axially loaded steel rods. Following the GSAÂź-procedure, which is a well established glued-in rods joint in Switzerland, rods with metric thread were bonded in glulam made of Norway spruce lamellas using an epoxy-type adhesive. The tests showed that the influence of the timber density can be quantified by a power function of ρ with an exponent of 0.6. The parameters length of the glued zone ℓ and diameter of the hole d H can be summarized in the slenderness ratio λ = ℓ/d H, which itself is related to the mean shear strength in the anchoring zone by an exponent of approximately −1/3. In order to prevent the specimens from premature splitting, distances between the axis of the rod and the edge of the specimen of 2.3 times the diameter of the rod have been use

    The pharmacokinetics of nebulized nanocrystal budesonide suspension in healthy volunteers.

    Get PDF
    Nanocrystal budesonide (nanobudesonide) is a suspension for nebulization in patients with steroid-responsive pulmonary diseases such as asthma. The pharmacokinetics and safety of the product were compared to those of Pulmicort Respules. Sixteen healthy volunteers were administered nanobudesonide 0.5 and 1.0 mg, Pulmicort Respules 0.5 mg, and placebo in a four-way, randomized crossover design. All nebulized formulations were well tolerated, with no evidence of bronchospasm. Nebulization times were significantly shorter for nanobudesonide compared to Pulmicort Respules. Because of a low oral bioavailability, plasma concentration of budesonide is a good marker of lung-delivered dose. The pharmacokinetics of nanobudesonide 0.5 and 1.0 mg were approximately dose proportional with respect to Cmax, AUC(0-t), and AUC(0-infinity). Nanobudesonide 0.5 mg and Pulmicort Respules 0.5 mg exhibited similar AUCs, suggesting a similar extent of pulmonary absorption. A higher Cmax was noted with nanobudesonide 0.5 mg, and the tmax was significantly different, suggesting a more rapid rate of drug delivery of nanobudesonide 0.5 mg than Pulmicort Respules. In conclusion, nebulized nanobudesonide 0.5 mg was safe in healthy volunteers, with a similar extent of absorption as Pulmicort Respules

    Evidence for increased olfactory receptor gene repertoire size in two nocturnal bird species with well-developed olfactory ability

    Get PDF
    <p>Abstract</p> <p>Background</p> <p>In vertebrates, the molecular basis of the sense of smell is encoded by members of a large gene family, namely olfactory receptor (OR) genes. Both the total number of OR genes and the proportion of intact OR genes in a genome may indicate the importance of the sense of smell for an animal. There is behavioral, physiological, and anatomical evidence that some bird species, in particular nocturnal birds, have a well developed sense of smell. Therefore, we hypothesized that nocturnal birds with good olfactory abilities have evolved (i) more OR genes and (ii) more intact OR genes than closely related and presumably less 'olfaction-dependent' day-active avian taxa.</p> <p>Results</p> <p>We used both non-radioactive Southern hybridization and PCR with degenerate primers to investigate whether two nocturnal bird species that are known to rely on olfactory cues, the brown kiwi (<it>Apteryx australis</it>) and the kakapo (<it>Strigops habroptilus</it>), have evolved a larger OR gene repertoire than their day-active, closest living relatives (for kiwi the emu <it>Dromaius novaehollandiae</it>, rhea <it>Rhea americana</it>, and ostrich <it>Struthio camelus </it>and for kakapo the kaka <it>Nestor meridionalis </it>and kea <it>Nestor notabilis</it>). We show that the nocturnal birds did not have a significantly higher proportion of intact OR genes. However, the estimated total number of OR genes was larger in the two nocturnal birds than in their relatives.</p> <p>Conclusion</p> <p>Our results suggest that ecological niche adaptations such as daily activity patterns may have shaped avian OR gene repertoires.</p

    Coronal Emission Measures and Abundances for Moderately Active K Dwarfs Observed by Chandra

    Full text link
    We have used Chandra to resolve the nearby 70 Oph (K0 V+K5 V) and 36 Oph (K1 V+K1 V) binary systems for the first time in X-rays. The LETG/HRC-S spectra of all four of these stars are presented and compared with an archival LETG spectrum of another moderately active K dwarf, Epsilon Eri. Coronal densities are estimated from O VII line ratios and emission measure distributions are computed for all five of these stars. We see no substantial differences in coronal density or temperature among these stars, which is not surprising considering that they are all early K dwarfs with similar activity levels. However, we do see significant differences in coronal abundance patterns. Coronal abundance anomalies are generally associated with the first ionization potential (FIP) of the elements. On the Sun, low-FIP elements are enhanced in the corona relative to high-FIP elements, the so-called "FIP effect." Different levels of FIP effect are seen for our stellar sample, ranging from 70 Oph A, which shows a prominent solar-like FIP effect, to 70 Oph B, which has no FIP bias at all or possibly even a weak inverse FIP effect. The strong abundance difference exhibited by the two 70 Oph stars is unexpected considering how similar these stars are in all other respects (spectral type, age, rotation period, X-ray flux). It will be difficult for any theoretical explanation for the FIP effect to explain how two stars so similar in all other respects can have coronae with different degrees of FIP bias. Finally, for the stars in our sample exhibiting a FIP effect, a curious difference from the solar version of the phenomenon is that the data seem to be more consistent with the high-FIP elements being depleted in the corona rather than a with a low-FIP enhancementComment: 35 pages, 8 figures, AASTEX v5.0 plus EPSF extensions in mkfig.sty; accepted by Ap

    Characterization of the TruSense S310 Laser Range System for Contact-less Measurement of Liquid Levels in Large-Volume Neutrino Detectors

    Full text link
    Neutrino experiments often use large volumes of water, organic scintillators or noble liquids as active detection material. Due to the large hydrostatic and buoyancy forces involved, precise knowledge of the liquid levels inside the detector tank are mandatory. Here we present the main characteristics of the TruSense S310 Laser Range System. Level measurements can be performed without direct contact to the liquid and through a gas-proof acrylic window, thus preserving the strict radiopurity and chemical requirements of the target liquid. We report the results of a suit of laboratory experiments for short-term precision tests (±\pm5\,mm) and long-term stability studies. Moreover, we demonstrate that the infrared laser can be used while standard bi-alkali PMTs are operational. We discuss the mechanical layout and integration of the system in the OSIRIS pre-detector that will monitor the radiopurity of the liquid scintillator for the large-volume neutrino experiment JUNO

    Cryogenic silicon detectors with implanted contacts for the detection of visible photons using the Neganov-Luke Effect

    Full text link
    There is a common need in astroparticle experiments such as direct dark matter detection, 0{\nu}\b{eta}\b{eta} (double beta decay without emission of neutrinos) and Coherent Neutrino Nucleus Scattering experiments for light detectors with a very low energy threshold. By employing the Neganov-Luke Effect, the thermal signal of particle interactions in a semiconductor absorber operated at cryogenic temperatures, can be amplified by drifting the photogenerated electrons and holes in an electric field. This technology is not used in current experiments, in particular because of a reduction of the signal amplitude with time which is due to trapping of the charges within the absorber. We present here the first results of a novel type of Neganov-Luke Effect detector with an electric field configuration designed to improve the charge collection within the semiconductor.Comment: 6 pages, 5 figures, submitted to Journal of Low Temperature Physic

    A modified expression of the major hydrolase activator in Hypocrea jecorina (Trichoderma reesei) changes enzymatic catalysis of biopolymer degradation

    Get PDF
    AbstractHypocrea jecorina (anamorph Trichoderma reesei) is a saprophytic fungus that produces hydrolases, which are applied in different types of industries and used for the production of biofuel. A recombinant Hypocrea strain, which constantly expresses the main transcription activator of hydrolases (Xylanase regulator 1), was found to grow faster on xylan and its monomeric backbone molecule d-xylose. This strain also showed improved ability of clearing xylan medium on plates. Furthermore, this strain has a changed transcription profile concerning genes encoding for hydrolases and enzymes associated with degradation of (hemi)celluloses. We demonstrated that enzymes of this strain from a xylan cultivation favoured break down of hemicelluloses to the monomer d-xylose compared to the parental strain, while the enzymes of the latter one formed more xylobiose. Applying supernatants from cultivation on carboxymethylcellulose in enzymatic conversion of hemicelluloses, the enzymes of the recombinant strain were clearly producing more of both, d-xylose and xylobiose, compared to the parental strain. Altogether, these results point to a changed hydrolase expression profile, an enhanced capability to form the xylan-monomer d-xylose and the assumption that there is a disordered induction pattern if the Xylanase regulator 1 is de-regulated in Hypocrea
    • 

    corecore