331 research outputs found
Large Size Telescope camera support structures for the Cherenkov Telescope Array
The design of the camera support structures for the Cherenkov Telescope Array
(CTA) Large Size Telescopes (LSTs) is based on an elliptical arch geometry
reinforced along its orthogonal projection by two symmetric sets of stabilizing
ropes. The main requirements in terms of minimal camera displacement, minimal
weight, minimal shadowing on the telescope mirror, maximal strength of the
structures and fast dynamical stabilization have led to the application of
Carbon Fibre Plastic Reinforced (CFPR) technologies. This work presents the
design, static and dynamic performance of the telescope fulfilling critical
specifications for the major scientific objectives of the CTA LST, e.g. Gamma
Ray Burst detection.Comment: In Proceedings of the 33rd International Cosmic Ray Conference
(ICRC2013), Rio de Janeiro (Brazil). All CTA contributions at arXiv:1307.223
CLIC Main Beam Quadrupole, Eigen mode computation
In this report, we summarise the work done on the CLIC Main Beam Quadrupole. There are about 4000 MB quadrupoles of 4 types with lengths ranging from 420mm to 1900mm. In order to obtain the desired CLIC luminosity, the MB quadrupoles have to be stable to 1nm above 1Hz. The region of interest for the study is between 0.5Hz and about 100Hz. In order to achieve the specifications, the magnet should not have any resonance peaks in this region of Interest. In addition, the magnet on its support shouldn’t have any resonance peak in the same frequency range. The first step is to determine if the designed magnet has its first resonance peak above 100Hz. We are studying the longest quadrupole more susceptible to internal resonances. In a second step, the magnet on ideal supporting points has been evaluated. The current magnet design can be seen on following figure. One can see that it is composed of 4 quadrants assembled so as to have a quadrupole magnetic field. As a last step, the mechanical model has been used to study the influence of the quadrant assembly. Note that in this report, the quadrant design varies slightly from one calculation to another since these studies have been performed in parallel with the magnet design process. It can be noticed that the results of the calculations are not significantly influenced by these design variations. In the last paragraph, the latest design has been considered to build finite element model
Stabilization study at the sub-nanometer level at the interaction point of the future Compact Linear Collider
International audienc
Sub-nanometer active seismic isolator control
Ambitious projects such as the design of the future Compact Linear Collider (CLIC) require challenging parameters and technologies. Stabilization of the CLIC particle beam is one of these challenges. Ground motion (GM) is the main source of beam misalignment. Beam dynamics controls are however efficient only at low frequency (<4Hz), due to the sampling of the beam at 50 Hz. Hence, ground motion mitigation techniques such as active stabilization are required. This paper shows a dedicated prototype able to manage vibration at a sub-nanometer scale. The use of cutting edge sensor technology is however very challenging for control applications as they are usually used for measurement purposes. Limiting factors such as sensor dynamics and noise lead to a performance optimization problem. The current state of the art in GM measurement and GM mitigation techniques is pointed out and shows limits of the technologies. The proposed active device is then described and a realistic model of the process has been established. A dedicated controller design combining feedforward and feedback techniques is presented and theoretical results in terms of Power Spectral Density (PSD) of displacement are compared to real time experimental results obtained with a rapid control prototyping tool
Stabilization study at the sub-nanometer level at the interaction point of the future Compact Linear Collider
International audienc
Active vibration isolation system for CLIC final focus
International audienceWith pinpoint accuracy, the next generation of Linear Collider such as CLIC will collide electron and positron beams at a centre of mass energy of 3 TeV with a desired peak luminosity of 2*1034 cm-2s-1. One of the many challenging features of CLIC is its ability to collide beams at the sub-nanometer scale at the Interaction Point (IP). Such a high level of accuracy could only be achieved by integrating Active Vibration Isolation systems (AVI) upstream of the collision to prevent the main source of vibration: Ground Motion (GM). Complementary control systems downstream of the collision (Interaction Point FeedBack (IPFB), Orbit FeedBack (OFB)) allow low frequency vibration rejection. This paper focuses on a dedicated AVI table designed for the last focusing quadrupole (QD0) where the specifications are the most stringent. Combining FeedForward (FF) and FeedBack (FB) techniques, the prototype is able to reduce GM down to 0.6 nm RMS(4Hz) experimentally without any load. These performances couldn't be achieved without cutting edge-technology such as sub-nanometer piezo actuators, ultra-low noise accelerometers and seismometers and an accurate guidance system. The whole AVI system is described in details. Further developments concern the integration of the final focusing magnet above the AVI table, first as part of the simulation with its dynamical model, and finally, as a realistic prototype
Pulsed quantum optomechanics
Studying mechanical resonators via radiation pressure offers a rich avenue
for the exploration of quantum mechanical behavior in a macroscopic regime.
However, quantum state preparation and especially quantum state reconstruction
of mechanical oscillators remains a significant challenge. Here we propose a
scheme to realize quantum state tomography, squeezing and state purification of
a mechanical resonator using short optical pulses. The scheme presented allows
observation of mechanical quantum features despite preparation from a thermal
state and is shown to be experimentally feasible using optical microcavities.
Our framework thus provides a promising means to explore the quantum nature of
massive mechanical oscillators and can be applied to other systems such as
trapped ions.Comment: 9 pages, 4 figure
Interaction point feedback design and integrated simulations to stabilize the CLIC final focus
International audienceThe Compact Linear Collider (CLIC) accelerator has strong precision requirements on offset position between the beams. The beam which is sensitive to ground motion needs to be stabilized to unprecedented requirements. Different Beam Based Feedback (BBF) algorithms such as Orbit Feedback (OFB) and Beam-Beam Offset Feedback (BBOF) have been designed. This paper focuses on the BBOF control which could be added to the CLIC baseline. It has been tested for different ground motion models in the presence of noises or disturbances and uses digital linear control with or without an adaptive loop. The simulations demonstrate that it is possible to achieve the required performances and quantify the maximum allowed noise level. This amount of admitted noises and disturbances is given in terms of an equivalent disturbance on the position of the magnet that controls the beam offset. Due to the limited sampling frequency of the process, the control loop is in a very small bandwidth. The study shows that these disturbances have to be lowered by other means in the higher frequency range
Determination of the vacuum optomechanical coupling rate using frequency noise calibration
The strength of optomechanical interactions in a cavity optomechanical system
can be quantified by a vacuum coupling rate \vcr analogous to cavity quantum
electrodynamics. This single figure of merit removes the ambiguity in the
frequently quoted coupling parameter defining the frequency shift for a given
mechanical displacement, and the effective mass of the mechanical mode. Here we
demonstrate and verify a straightforward experimental technique to derive the
vacuum optomechanical coupling rate. It only requires applying a known
frequency modulation of the employed electromagnetic probe field and knowledge
of the mechanical oscillator's occupation. The method is experimentally
verified for a micromechanical mode in a toroidal whispering-gallery-resonator
and a nanomechanical oscillator coupled to a toroidal cavity via its near
field.Comment: 11 pages, 2 figure
- …