Antimicrobial activity of Plectranthus amboinicus solvent extracts against Human Pathogenic Bacteria and Fungi

Plectranthus amboinicus or locally known as bangun-bangun, is an indigenous vegetable which can be freshly eaten. However, the plant is unpopular among local people and being neglected. It has been reported to be traditionally used for medicine to cure common illnesses such as cough, stomachache, headache and skin infection. Based on the potential, a study was conducted to bioprospect the antimicrobial activity of the essential oil. Plectranthus amboinicus essential oil of methanol and chloroform extract was tested against nine bacteria and four fungi i.e., Escherichia coli, Proteus vulgaris, Pseudomonas aeruginosa, Shigella flexneri, Klebsiella pneumoniae, Enterococcus faecal, Staphylococcus aureus, Salmonella typhi, Bacillus cereus, Candida albicans, Aspergillus niger, Aspergillus fumigatus and Aspergillus flavus. The methanol extract of Plectranthus amboinicus showed the maximum antibacterial activity against the bacteria Klebsiella pneumoniae and fungi Candida albicans. The antimicrobial activity of Plectranthus amboinicus was more at 100 mg/ml concentration when compared to 50 mg/ml concentration. Comparatively, the Methanol extract of Plectranthus amboinicus exhibited maximum antimicrobial activity when compared to Chloroform extract. The Plectranthus amboinicus has showed good antimicrobial activity against most of the bacteria and only one fungal yeast Candida albicans. No zone of inhibition was recorded against other fungal isolates like Aspergillus niger, Aspergillus flavus, Aspergillus fumigatus and Negative DMSO control. Keywords: Plectranthus amboinicus, Bacteria, Fungi, Antimicrobial activity and Well diffusion assay

Systemic pro-inflammatory cytokine status following therapeutic hypothermia in a piglet hypoxia-ischemia model

BACKGROUND: Inflammatory cytokines are implicated in the pathogenesis of perinatal hypoxia-ischemia (HI). The influence of hypothermia (HT) on cytokines after HI is unclear. Our aim was to assess in a piglet asphyxia model, under normothermic (NT) and HT conditions: (i) the evolution of serum cytokines over 48 h and (ii) cerebrospinal fluid (CSF) cytokine levels at 48 h; (iii) serum pro/anti-inflammatory cytokine profile over 48 h and (iv) relation between brain injury measured by magnetic resonance spectroscopy (MRS) and brain TUNEL positive cells with serum cytokines, serum pro/anti-inflammatory cytokines and CSF cytokines. METHODS: Newborn piglets were randomized to NT (n = 5) or HT (n = 6) lasting 2-26 h after HI. Serum samples were obtained 4-6 h before, during and at 6-12 h intervals after HI; CSF was obtained at 48 h. Concentrations of interleukin (IL)-1beta, -4, -6, -8, -10 and TNF-alpha were measured and pro/anti-inflammatory status compared between groups. White matter and thalamic voxel lactate/N-acetyl aspartate (Lac/NAA) (a measure of both oxidative metabolism and neuronal loss) were acquired at baseline, after HI and at 24 and 36 h. RESULTS: Lac/NAA was reduced at 36 h with HT compared to NT (p = 0.013 basal ganglia and p = 0.033 white matter). HT showed lower serum TNF-alpha from baseline to 12 h (p < 0.05). Time-matched (acquired within 5 h of each other) serum cytokine and MRS showed correlations between Lac/NAA and serum IL-1beta and IL-10 (all p < 0.01). The pro/anti-inflammatory ratios IL-1beta/IL-10, IL-6/IL-10, IL-4/IL-10 and IL-8/IL-10 were similar in NT and HT groups until 36 h (24 h for IL-6/IL-10); after this, 36 h pro/anti-inflammatory cytokine ratios in the serum were higher in HT compared to NT (p < 0.05), indicating a pro-inflammatory cytokine surge after rewarming in the HT group. In the CSF at 48 h, IL-8 was lower in the HT group (p < 0.05). At 48 h, CSF TNF-alpha correlated with Lac/NAA (p = 0.02) and CSF IL-8 correlated with white matter TUNEL positive cell death (p = 0.04). CONCLUSIONS: Following cerebral HI, there was a systemic pro-inflammatory surge after rewarming in the HT group, which is counterintuitive to the putative neuroprotective effects of HT. While serum cytokines were variable, elevations in CSF inflammatory cytokines at 48 h were associated with MRS Lac/NAA and white matter cell death

Microscopic characteristics of biodiesel – Graphene oxide nanoparticle blends and their Utilisation in a compression ignition engine

Use of nano-additives in biofuels is an important research and development topic for achieving optimum engine performance with reduced emissions. In this study, rice bran oil was converted into biodiesel and graphene oxide (GO) nanoparticles were infused into biodiesel-diesel blends. Two blends containing (i) 5% biodiesel, 95% diesel and 30 ppm GO (B5D95GO30) and (ii) 15% biodiesel, 85% diesel and 30 ppm GO (B15D85GO30) were prepared. The fuel properties like heating value, kinematic viscosity, cetane number, etc. of the nanoadditives–biodiesel-diesel blends (NBDB) were measured. Effects of injection timing (IT) on the performance, combustion and emission characteristics were studied. It was observed that both B15D85GO30 and B5D95GO30 blends at IT23° gave up to 13.5% reduction in specific fuel consumption. Compared to diesel, the brake thermal efficiency was increased by 7.62% for B15D85GO30 at IT23° and IT25°. An increase in IT from 23° to 25° deteriorated the indicated thermal efficiency by 6.68% for B15D85GO30. At maximum load condition, the peak heat release rates of NBDB were found to be lower than the pure diesel at both IT. The CO, CO2 & NOx emissions were reduced by 2–8%. The study concluded that B15D85GO30 at IT23° gave optimum results in terms of performance, combustion and emission characteristics

Finite difference analysis on radiative flow on a perpendicular plate using the influence of thermal conductivity

This study aims to investigate the influence of radiation, thermal conductivity and variable viscosity on natural convective flow on a semi-infinite perpendicular plate. Variable viscosity, thermal conductivity and thermal radiation are considered for the given study. The dimensional governing equations are framed with the use of the mentioned parameters and then these equations were converted into dimensionless equations by applying non dimensional quantities. The main aim of this study is to find the Nusselt number and skin friction for both air and water for considered parameters. Using the finite difference method through Fortran software, numerical solutions to the governing heat equations and dimensionless momentum equations were computed. The results for the parameters thermal conductivity, variable viscosity, radiation, and Prandtl number for both air and water are displayed via various graphs. The skin friction coefficients, Nusselt parameter, and local Nusselt numbers were discussed for both the air and water. The key conclusions of this study are that the succeeding velocity declines as the radiation's increases. By increasing the radiation value and the fluctuation time, the temperature distribution increases. Notably, the temperature profile increases significantly when the variable viscosity parameter decreases

The Influence of Processing on Microstructural Development, Tensile Response and Fracture Behavior of Aluminum Alloy 5083

In this paper, the specific influence of quasi-isostatic forging and rolling of cryomilled powder on microstructural development and resultant tensile deformation and fracture behavior of aluminum alloy 5083 is highlighted and comparison made with the coarse grained counterpart. The specific influence and contribution of strain hardening to enhancing strength of the ultra-fine grain microstructure of the aluminum alloy is presented and discussed. It is shown that the capability of the ultra fine grain microstructure to recover strength through the mechanism of work hardening is quite similar to the conventionally processed counterpart. The influence and role of intrinsic microstructural features in governing tensile deformation and fracture behavior is elaborated upon. The viable microscopic mechanisms governing final fracture behavior is discussed in light of the competing and mutually interactive influences of nature of loading, intrinsic microstructural effects, and deformation kinetics. Key Words: aluminum alloy 5083, processing, microstructure, tensile properties, fractur

Quasi-Static Deformation and Final Fracture Behaviour of Aluminium Alloy 5083: Influence of Cryomilling

The commercial aluminium alloy 5083 was processed via cryomilling to produce nanocrystalline (NC) powders with an average grain size of ∼25–50 nm. The powders were subsequently degassed at 723 K (450°C), pre-heated and immediately quasi-isostatic (QI)-forged to produce a thermally stable bulk ultrafine grain (UFG) material having average grain size values ranging from 190 to 350 nm, depending on the processing conditions used. In this paper, the tensile properties and fracture behaviour of the bulk UFG material are presented and compared with the tensile properties of its conventionally processed counterpart. The specific influence of preheat temperature on strength and ductility of the alloy is briefly discussed. Three different pre-heat temperatures of 523, 623 and 723 K (250, 350 and 450°C) were chosen and used with the primary objective of controlling grain growth during forging. The influence of preheat temperature on tensile deformation and final fracture behaviour is highlighted. The macroscopic fracture modes of the bulk nanostructured material (BNM) prepared following three pre-heat temperatures are investigated. The microscopic mechanisms controlling tensile deformation and final fracture behaviour are discussed with regards to the intrinsic microstructural effects in the UFG alloy, nature of loading, and the kinetics and mechanisms of deformation