Cavitation-induced force transition in confined viscous liquids under traction

We perform traction experiments on simple liquids highly confined between parallel plates. At small separation rates, we observe a simple response corresponding to a convergent Poiseuille flow. Dramatic changes in the force response occur at high separation rates, with the appearance of a force plateau followed by an abrupt drop. By direct observation in the course of the experiment, we show that cavitation accounts for these features which are reminiscent of the utmost complex behavior of adhesive films under traction. Surprisingly enough, this is observed here in purely viscous fluids.Comment: Submitted to Physical Review Letters on May 31, 2002. Related informations on http://www.crpp.u-bordeaux.fr/tack.htm

Molecular weight effects on chain pull-out fracture of reinforced polymeric interfaces

Using Brownian dynamics, we simulate the fracture of polymer interfaces reinforced by diblock connector chains. We find that for short chains the interface fracture toughness depends linearly on the degree of polymerization $N$ of the connector chains, while for longer chains the dependence becomes $N^{3/2}$. Based on the geometry of initial chain configuration, we propose a scaling argument that accounts for both short and long chain limits and crossover between them.Comment: 5 pages, 3 figure

Continuous EB welding of the reinforcement of the CMS conductor

The Compact Muon Solenoid (CMS) is one of the general-purpose detectors to be provided for the LHC project at CERN. The design field of the CMS superconducting magnet is 4 T, the magnetic length is 12.5 m and the free bore is 6 m. In order to withstand the electro-mechanical forces during the operation of the CMS magnet, the superconducting cable embedded in a 99.998% pure aluminum matrix is reinforced with two sections of aluminum alloy EN AW-6082 assembled by continuous Electron Beam Welding (EBW). A dedicated production line has been designed by Techmeta, a leading company in the field of EBW. The production line has a total length of 70 m. Non-stop welding of each of the 20 lengths of 2.5 km, required to build the coil, will last 22 hours. EBW is the most critical process involved in the production line. The main advantage of the EBW process is to minimize the Heat Affected Zone; this is particularly important for avoiding damage to the superconducting cable located only 4.7 mm from the welded joints. Two welding guns of 20 kW each operate in parallel in a vacuum chamber fitted with dynamic airlocks. After welding, the conductor is continuously machined on the four faces and on each corner to obtain the required dimensions and surface finish. Special emphasis has been put on quality monitoring. All significant production parameters are recorded during operation and relevant samples are taken from each produced length for destructive testing purposes. In addition, a continuous phased array ultrasonic checking device is located immediately after the welding unit for the continuous welding quality control, along with a dimension laser measurement unit following the machining. (8 refs)

Enhancement of the Adhesive Properties by Optimizing the Water Content in PNIPAM-Functionalized Complex Coacervates

Most commercially available soft tissue glues offer poor performance in the human body. We have developed an injectable adhesive whose setting mechanism is activated by a change in environmental factors, i.e., temperature and/or ionic strength. The material and setting process are inspired by the adhesive processing mechanism observed in natural maritime glues. Complex coacervation, a liquid-liquid phase separation between oppositely charged polyelectrolytes, is thought to play an important role in the processing. Complex coacervates are characterized by a high water content, which inevitably weakens the glue. Here, we aim to increase the adhesive performance by systematically tuning the water content. Among the several strategies here explored, the most effective one is the mechanical removal of water using an extruder, resulting in an increase of work of adhesion by 1 order of magnitude compared to the original formulation

Tensile Fracture of Welded Polymer Interfaces: Miscibility, Entanglements and Crazing

Large-scale molecular simulations are performed to investigate tensile failure of polymer interfaces as a function of welding time $t$. Changes in the tensile stress, mode of failure and interfacial fracture energy $G_I$ are correlated to changes in the interfacial entanglements as determined from Primitive Path Analysis. Bulk polymers fail through craze formation, followed by craze breakdown through chain scission. At small $t$ welded interfaces are not strong enough to support craze formation and fail at small strains through chain pullout at the interface. Once chains have formed an average of about one entanglement across the interface, a stable craze is formed throughout the sample. The failure stress of the craze rises with welding time and the mode of craze breakdown changes from chain pullout to chain scission as the interface approaches bulk strength. The interfacial fracture energy $G_I$ is calculated by coupling the simulation results to a continuum fracture mechanics model. As in experiment, $G_I$ increases as $t^{1/2}$ before saturating at the average bulk fracture energy $G_b$. As in previous simulations of shear strength, saturation coincides with the recovery of the bulk entanglement density. Before saturation, $G_I$ is proportional to the areal density of interfacial entanglements. Immiscibiltiy limits interdiffusion and thus suppresses entanglements at the interface. Even small degrees of immisciblity reduce interfacial entanglements enough that failure occurs by chain pullout and $G_I \ll G_b$

Cell transformation assays for prediction of carcinogenic potential: State of the science and future research needs

Copyright @ 2011 The Authors. This is an Open Access article distributed under the terms of the Creative Commons Attribution Non-Commercial License (http://creativecommons.org/licenses/by-nc/3.0), which permits unrestricted non-commercial use, distribution, and reproduction in any medium, provided the original work is properly cited.Cell transformation assays (CTAs) have long been proposed as in vitro methods for the identification of potential chemical carcinogens. Despite showing good correlation with rodent bioassay data, concerns over the subjective nature of using morphological criteria for identifying transformed cells and a lack of understanding of the mechanistic basis of the assays has limited their acceptance for regulatory purposes. However, recent drivers to find alternative carcinogenicity assessment methodologies, such as the Seventh Amendment to the EU Cosmetics Directive, have fuelled renewed interest in CTAs. Research is currently ongoing to improve the objectivity of the assays, reveal the underlying molecular changes leading to transformation and explore the use of novel cell types. The UK NC3Rs held an international workshop in November 2010 to review the current state of the art in this field and provide directions for future research. This paper outlines the key points highlighted at this meeting

On the nature of surface roughness with application to contact mechanics, sealing, rubber friction and adhesion

Surface roughness has a huge impact on many important phenomena. The most important property of rough surfaces is the surface roughness power spectrum C(q). We present surface roughness power spectra of many surfaces of practical importance, obtained from the surface height profile measured using optical methods and the Atomic Force Microscope. We show how the power spectrum determines the contact area between two solids. We also present applications to sealing, rubber friction and adhesion for rough surfaces, where the power spectrum enters as an important input.Comment: Topical review; 82 pages, 61 figures; Format: Latex (iopart). Some figures are in Postscript Level

A Novel Role for MAPKAPK2 in Morphogenesis during Zebrafish Development

One of the earliest morphogenetic processes in the development of many animals is epiboly. In the zebrafish, epiboly ensues when the animally localized blastoderm cells spread, thin over, and enclose the vegetally localized yolk. Only a few factors are known to function in this fundamental process. We identified a maternal-effect mutant, betty boop (bbp), which displays a novel defect in epiboly, wherein the blastoderm margin constricts dramatically, precisely when half of the yolk cell is covered by the blastoderm, causing the yolk cell to burst. Whole-blastoderm transplants and mRNA microinjection rescue demonstrate that Bbp functions in the yolk cell to regulate epiboly. We positionally cloned the maternal-effect bbp mutant gene and identified it as the zebrafish homolog of the serine-threonine kinase Mitogen Activated Protein Kinase Activated Protein Kinase 2, or MAPKAPK2, which was not previously known to function in embryonic development. We show that the regulation of MAPKAPK2 is conserved and p38 MAP kinase functions upstream of MAPKAPK2 in regulating epiboly in the zebrafish embryo. Dramatic alterations in calcium dynamics, together with the massive marginal constrictive force observed in bbp mutants, indicate precocious constriction of an F-actin network within the yolk cell, which first forms at 50% epiboly and regulates epiboly progression. We show that MAPKAPK2 activity and its regulator p38 MAPK function in the yolk cell to regulate the process of epiboly, identifying a new pathway regulating this cell movement process. We postulate that a p38 MAPKAPK2 kinase cascade modulates the activity of F-actin at the yolk cell margin circumference allowing the gradual closure of the blastopore as epiboly progresses