An Efficient Algorithm to Selectively Gate Scan Cells for Capture Power Reduction

[[abstract]]Recently, power dissipation in full-scan testing has brought a great challenge for test engineers. In addition to shift power reduction, excessive switching activity during capture operation may lead to circuit malfunction and yield loss. In this paper, a new algorithm is proposed with using clock gating technique on a part of the scan cells to prevent the internal circuit from unnecessary transitions. These scan cells are divided into several exclusive scan groups. For each test vector, only a portion of the scan groups are activated to store the test response per capture cycle. The proposed method can reduce the capture power dissipation without any influence on fault coverage or testing time. Experimental results for ISCAS'89 benchmark circuits show that the capture power reduction in test sequence can up to 55%.[[notice]]補正完畢[[incitationindex]]EI[[booktype]]紙

Studies on Core-Based Testing of System-on-Chips Using Functional Bus and Network-on-Chip Interconnects

The tests of a complex system such as a microprocessor-based system-onchip (SoC) or a network-on-chip (NoC) are difficult and expensive. In this thesis, we propose three core-based test methods that reuse the existing functional interconnects-a flat bus, hierarchical buses of multiprocessor SoC's (MPSoC), and a N oC-in order to avoid the silicon area cost of a dedicated test access mechanism (TAM). However, the use of functional interconnects as functional TAM's introduces several new problems. During tests, the interconnects-including the bus arbitrator, the bus bridges, and the NoC routers-operate in the functional mode to transport the test stimuli and responses, while the core under tests (CUT) operate in the test mode. Second, the test data is transported to the CUT through the functional bus, and not directly to the test port. Therefore, special core test wrappers that can provide the necessary control signals required by the different functional interconnect are proposed. We developed two types of wrappers, one buffer-based wrapper for the bus-based systems and another pair of complementary wrappers for the NoCbased systems. Using the core test wrappers, we propose test scheduling schemes for the three functionally different types of interconnects. The test scheduling scheme for a flat bus is developed based on an efficient packet scheduling scheme that minimizes both the buffer sizes and the test time under a power constraint. The schedulingscheme is then extended to take advantage of the hierarchical bus architecture of the MPSoC systems. The third test scheduling scheme based on the bandwidth sharing is developed specifically for the NoC-based systems. The test scheduling is performed under the objective of co-optimizing the wrapper area cost and the resulting test application time using the two complementary NoC wrappers. For each of the proposed methodology for the three types of SoC architec .. ture, we conducted a thorough experimental evaluation in order to verify their effectiveness compared to other methods

Analysis and design implementation using VHDL and NAND circuit for Linear Feedback Shift Register (LFSR) for Low Power BIST

No Abstrac

REDUCING POWER DURING MANUFACTURING TEST USING DIFFERENT ARCHITECTURES

Power during manufacturing test can be several times higher than power consumption in functional mode. Excessive power during test can cause IR drop, over-heating, and early aging of the chips. In this dissertation, three different architectures have been introduced to reduce test power in general cases as well as in certain scenarios, including field test. In the first architecture, scan chains are divided into several segments. Every segment needs a control bit to enable capture in a segment when new faults are detectable on that segment for that pattern. Otherwise, the segment should be disabled to reduce capture power. We group the control bits together into one or more control chains. To address the extra pin(s) required to shift data into the control chain(s) and significant post processing in the first architecture, we explored a second architecture. The second architecture stitches the control bits into the chains they control as EECBs (embedded enable capture bits) in between the segments. This allows an ATPG software tool to automatically generate the appropriate EECB values for each pattern to maintain the fault coverage. This also works in the presence of an on-chip decompressor. The last architecture focuses primarily on the self-test of a device in a 3D stacked IC when an existing FPGA in the stack can be programmed as a tester. We show that the energy expended during test is significantly less than would be required using low power patterns fed by an on-chip decompressor for the same very short scan chains

A novel scan segmentation design method for avoiding shift timing failure in scan testing

ITC : 2011 IEEE International Test Conference , 20-22 Sep. 2011 , Anaheim, CA, USAHigh power consumption in scan testing can cause undue yield loss which has increasingly become a serious problem for deep-submicron VLSI circuits. Growing evidence attributes this problem to shift timing failures, which are primarily caused by excessive switching activity in the proximities of clock paths that tends to introduce severe clock skew due to IR-drop-induced delay increase. This paper is the first of its kind to address this critical issue with a novel layout-aware scheme based on scan segmentation design, called LCTI-SS (Low-Clock-Tree-Impact Scan Segmentation). An optimal combination of scan segments is identified for simultaneous clocking so that the switching activity in the proximities of clock trees is reduced while maintaining the average power reduction effect on conventional scan segmentation. Experimental results on benchmark and industrial circuits have demonstrated the advantage of the LCTI-SS scheme

A Pixel Vertex Tracker for the TESLA Detector

In order to fully exploit the physics potential of a e+e- linear collider, such as TESLA, a Vertex Tracker providing high resolution track reconstruction is required. Hybrid Silicon pixel sensors are an attractive sensor technology option due to their read-out speed and radiation hardness, favoured in the high rate TESLA environment, but have been so far limited by the achievable single point space resolution. A novel layout of pixel detectors with interleaved cells to improve their spatial resolution is introduced and the results of the characterisation of a first set of test structures are discussed. In this note, a conceptual design of the TESLA Vertex Tracker, based on hybrid pixel sensors is presentedComment: 20 pages, 11 figure

A survey of scan-capture power reduction techniques

With the advent of sub-nanometer geometries, integrated circuits (ICs) are required to be checked for newer defects. While scan-based architectures help detect these defects using newer fault models, test data inflation happens, increasing test time and test cost. An automatic test pattern generator (ATPG) exercise’s multiple fault sites simultaneously to reduce test data which causes elevated switching activity during the capture cycle. The switching activity results in an IR drop exceeding the devices under test (DUT) specification. An increase in IR-drop leads to failure of the patterns and may cause good DUTs to fail the test. The problem is severe during at-speed scan testing, which uses a functional rated clock with a high frequency for the capture operation. Researchers have proposed several techniques to reduce capture power. They used various methods, including the reduction of switching activity. This paper reviews the recently proposed techniques. The principle, algorithm, and architecture used in them are discussed, along with key advantages and limitations. In addition, it provides a classification of the techniques based on the method used and its application. The goal is to present a survey of the techniques and prepare a platform for future development in capture power reduction during scan testing

Test Slice Difference Technique for Low-Transition Test Data Compression

[[notice]]補正完畢[[incitationindex]]EI[[booktype]]電子

Algorithms for Power Aware Testing of Nanometer Digital ICs

At-speed testing of deep-submicron digital very large scale integrated (VLSI) circuits has become mandatory to catch small delay defects. Now, due to continuous shrinking of complementary metal oxide semiconductor (CMOS) transistor feature size, power density grows geometrically with technology scaling. Additionally, power dissipation inside a digital circuit during the testing phase (for test vectors under all fault models (Potluri, 2015)) is several times higher than its power dissipation during the normal functional phase of operation. Due to this, the currents that flow in the power grid during the testing phase, are much higher than what the power grid is designed for (the functional phase of operation). As a result, during at-speed testing, the supply grid experiences unacceptable supply IR-drop, ultimately leading to delay failures during at-speed testing. Since these failures are specific to testing and do not occur during functional phase of operation of the chip, these failures are usually referred to false failures, and they reduce the yield of the chip, which is undesirable. In nanometer regime, process parameter variations has become a major problem. Due to the variation in signalling delays caused by these variations, it is important to perform at-speed testing even for stuck faults, to reduce the test escapes (McCluskey and Tseng, 2000; Vorisek et al., 2004). In this context, the problem of excessive peak power dissipation causing false failures, that was addressed previously in the context of at-speed transition fault testing (Saxena et al., 2003; Devanathan et al., 2007a,b,c), also becomes prominent in the context of at-speed testing of stuck faults (Maxwell et al., 1996; McCluskey and Tseng, 2000; Vorisek et al., 2004; Prabhu and Abraham, 2012; Potluri, 2015; Potluri et al., 2015). It is well known that excessive supply IR-drop during at-speed testing can be kept under control by minimizing switching activity during testing (Saxena et al., 2003). There is a rich collection of techniques proposed in the past for reduction of peak switching activity during at-speed testing of transition/delay faults ii in both combinational and sequential circuits. As far as at-speed testing of stuck faults are concerned, while there were some techniques proposed in the past for combinational circuits (Girard et al., 1998; Dabholkar et al., 1998), there are no techniques concerning the same for sequential circuits. This thesis addresses this open problem. We propose algorithms for minimization of peak switching activity during at-speed testing of stuck faults in sequential digital circuits under the combinational state preservation scan (CSP-scan) architecture (Potluri, 2015; Potluri et al., 2015). First, we show that, under this CSP-scan architecture, when the test set is completely specified, the peak switching activity during testing can be minimized by solving the Bottleneck Traveling Salesman Problem (BTSP). This mapping of peak test switching activity minimization problem to BTSP is novel, and proposed for the first time in the literature. Usually, as circuit size increases, the percentage of don’t cares in the test set increases. As a result, test vector ordering for any arbitrary filling of don’t care bits is insufficient for producing effective reduction in switching activity during testing of large circuits. Since don’t cares dominate the test sets for larger circuits, don’t care filling plays a crucial role in reducing switching activity during testing. Taking this into consideration, we propose an algorithm, XStat, which is capable of performing test vector ordering while preserving don’t care bits in the test vectors, following which, the don’t cares are filled in an intelligent fashion for minimizing input switching activity, which effectively minimizes switching activity inside the circuit (Girard et al., 1998). Through empirical validation on benchmark circuits, we show that XStat minimizes peak switching activity significantly, during testing. Although XStat is a very powerful heuristic for minimizing peak input-switchingactivity, it will not guarantee optimality. To address this issue, we propose an algorithm that uses Dynamic Programming to calculate the lower bound for a given sequence of test vectors, and subsequently uses a greedy strategy for filling don’t cares in this sequence to achieve this lower bound, thereby guaranteeing optimality. This algorithm, which we refer to as DP-fill in this thesis, provides the globally optimal solution for minimizing peak input-switching-activity and also is the best known in the literature for minimizing peak input-switching-activity during testing. The proof of optimality of DP-fill in minimizing peak input-switching-activity is also provided in this thesis