Low phase noise, high bandwidth frequency synthesis techniques

Thesis (Ph. D.)--Massachusetts Institute of Technology, Dept. of Electrical Engineering and Computer Science, 2005.Includes bibliographical references (p. 243-249).A quantization noise reduction technique is proposed that allows fractional-N frequency synthesizers to achieve high closed loop bandwidth and low output phase noise simultaneously. Quantization induced phase noise is the bottleneck in state-of-the-art synthesizer design, and results in a noise-bandwidth tradeoff that typically limits closed loop synthesizer bandwidths to be <100kHz for adequate phase noise performance to be achieved. Using the proposed technique, quantization noise is reduced to the point where intrinsic noise sources (VCO, charge-pump, reference and PFD noise) ultimately limit noise performance. An analytical model that draws an analogy between fractional-N frequency synthesizers and MASH A digital-to-analog converters is proposed. Calculated performance of a synthesizer implementing the proposed quantization noise reduction techniques shows excellent agreement with simulation results of a behavioral model. Behavioral modeling techniques that progressively incorporate non-ideal circuit behavior based on SPICE level simulations are proposed. The critical circuits used to build the proposed synthesizer are presented.(cont.) These include a divider retiming circuit that avoids meta-stability related to synchronizing an asynchronous signal, a timing mismatch compensation block used by a dual divider path PFD, and a unit element current source design for reduced output phase noise. Measurement results of a prototype 0.18/m CMOS synthesizer show that quantization noise is suppressed by 29dB when the proposed synthesizer architecture is compared to 2nd order EA frequency synthesizer. The 1MHz closed loop bandwidth allows the synthesizer to be modulated by up to 1Mb/s GMSK data for use as a transmitter with 1.8GHz and 900MHz outputs. The analytical model is used to back extract on-chip mismatch parameters that are not directly measurable. This represents a new analysis technique that is useful in the characterization of fractional-N frequency synthesizers.by Scott Edward Meninger.Ph.D

Integrated radio frequency synthetizers for wireless applications

This thesis consists of six publications and an overview of the research topic, which is also a summary of the work. The research described in this thesis concentrates on the design of phase-locked loop radio frequency synthesizers for wireless applications. In particular, the focus is on the implementation of the prescaler, the phase detector, and the chargepump. This work reviews the requirements set for the frequency synthesizer by the wireless standards, and how these requirements are derived from the system specifications. These requirements apply to both integer-N and fractional-N synthesizers. The work also introduces the special considerations related to the design of fractional-N phase-locked loops. Finally, implementation alternatives for the different building blocks of the synthesizer are reviewed. The presented work introduces new topologies for the phase detector and the chargepump, and improved topologies for high speed CMOS prescalers. The experimental results show that the presented topologies can be successfully used in both integer-N and fractional-N synthesizers with state-of-the-art performance. The last part of this work discusses the additional considerations that surface when the synthesizer is integrated into a larger system chip. It is shown experimentally that the synthesizer can be successfully integrated into a complex transceiver IC without sacrificing the performance of the synthesizer or the transceiver.reviewe

New strategies for low noise, agile PLL frequency synthesis

Phase-Locked Loop based frequency synthesis is an essential technique employed in wireless communication systems for local oscillator generation. The ultimate goal in any design of frequency synthesisers is to generate precise and stable output frequencies with fast switching and minimal spurious and phase noise. The conflict between high resolution and fast switching leads to two separate integer synthesisers to satisfy critical system requirements. This thesis concerns a new sigma-delta fractional-N synthesiser design which is able to be directly modulated at high data rates while simultaneously achieving good noise performance. Measured results from a prototype indicate that fast switching, low noise and spurious free spectra are achieved for most covered frequencies. The phase noise of the unmodulated synthesiser was measured −113 dBc/Hz at 100 kHz offset from the carrier. The intermodulation effect in synthesisers is capable of producing a family of spurious components of identical form to fractional spurs caused in quantisation process. This effect directly introduces high spurs on some channels of the synthesiser output. Numerical and analytic results describing this effect are presented and amplitude and distribution of the resulting fractional spurs are predicted and validated against simulated and measured results. Finally an experimental arrangement, based on a phase compensation technique, is presented demonstrating significant suppression of intermodulation-borne spurs. A new technique, pre-distortion noise shaping, is proposed to dramatically reduce the impact of fractional spurs in fractional-N synthesisers. The key innovation is the introduction in the bitstream generation process of carefully-chosen set of components at identical offset frequencies and amplitudes and in anti-phase with the principal fractional spurs. These signals are used to modify the Σ-Δ noise shaping, so that fractional spurs are effectively cancelled. This approach can be highly effective in improving spectral purity and reduction of spurious components caused by the Σ-Δ modulator, quantisation noise, intermodulation effects and any other circuit factors. The spur cancellation is achieved in the digital part of the synthesiser without introducing additional circuitry. This technique has been convincingly demonstrated by simulated and experimental results

A Low Voltage Delta-Sigma Fractional Frequency Divider for Multi-band WSN Frequency Synthesizers

A 1 V low voltage delta-sigma fractional-N frequency divider for multi-band (780/868/915 MHz and 2.4 GHz) WSN frequency synthesizers is presented. The frequency divider consists of a dual-modulus prescaler, a pulse-swallow counter and a delta-sigma modulator. The high-speed and low-voltage phase-switching dual-modulus prescaler is used in the frequency divider. Low threshold voltage transistors are applied to overcome low voltage supply and forward phase-switching technique is adopted to prevent glitches. The modified delta-sigma modulator with long output sequence length and less spurs is adopted to minimize the fractional spurs. The frequency divider is designed in 0.18 mm TSMC RF CMOS technology under 1 V supply instead of the standard 1.8 V supply. The total chip area is 1190 mm 485 mm including I/O pads. The post simulation results show the frequency divider operates normally over a wide range of 1.3-5.0 GHz and the core circuit (without test buffers) consumes 2.3 mW

Time-Offset Fractional-N PLLs for Heterodyne FMCW SAR

This text contains an investigation into the use of time-offset fractional-N phase locked loops (PLLs) for heterodyne frequency-modulated continuous-wave (FMCW) synthetic aperture radar (SAR) and the impact of spurii on such a system. Heterodyne receiver architectures avoid phenomena which limit the sensitivity of their homodyne counterparts, and enable certain inter-antenna feed-through suppression techniques. Despite these advantages, homodyne receivers are more prevalent owing to advantages in size, weight and cost. Designed to address this dilemma, the miloSAR is believed to be the only heterodyne FMCW SAR to employ a pair of time-offset fractional-N PLLs for waveform synthesis to enable low-cost heterodyning and simplify filter-based feed-through suppression. This system architecture is revealed to be susceptible to swept-offset spurii termed spur chirps which hinder the sensor's performance. While integer boundary spurs and phase detector harmonics infamously plague fractional-N PLLs, their resultant spur-chirps have not seen analysis in the context of FMCW SAR. Simulations and measurements reveal that these spurii significantly degrade SAR image quality in terms of peak sidelobe ratio, structural similarity index measure and root mean square error. To combat this, several suppression techniques were assessed, namely: time domain zeroing, PLL loop bandwidth reduction, and a novel method termed range-Doppler spur masking. A subset of these suppression techniques were applied to measured SAR data sets, including car-borne data measured in Iowa, USA and airborne data captured in Oudtshoorn, South Africa. These results show that the impact of spur chirps can be effectively quelled, meaning that time-offset fractional-N PLLs offer an attractive, low-cost approach to the implementation of heterodyne FMCW SAR

Techniques for high-performance digital frequency synthesis and phase control

Thesis (Ph. D.)--Massachusetts Institute of Technology, Dept. of Electrical Engineering and Computer Science, 2008.Includes bibliographical references (p. 183-190).This thesis presents a 3.6-GHz, 500-kHz bandwidth digital [delta][sigma] frequency synthesizer architecture that leverages a recently invented noise-shaping time-to-digital converter (TDC) and an all-digital quantization noise cancellation technique to achieve excellent in-band and out-of-band phase noise, respectively. In addition, a passive digital-to-analog converter (DAC) structure is proposed as an efficient interface between the digital loop filter and a conventional hybrid voltage-controlled oscillator (VCO) to create a digitally-controlled oscillator (DCO). An asynchronous divider structure is presented which lowers the required TDC range and avoids the divide-value-dependent delay variation. The prototype is implemented in a 0.13-am CMOS process and its active area occupies 0.95 mm². Operating under 1.5 V, the core parts, excluding the VCO output buffer, dissipate 26 mA. Measured phase noise at 3.67 GHz achieves -108 dBc/Hz and -150 dBc/Hz at 400 kHz and 20 MHz, respectively. Integrated phase noise at this carrier frequency yields 204 fs of jitter (measured from 1 kHz to 40 MHz). In addition, a 3.2-Gb/s delay-locked loop (DLL) in a 0.18-[mu]m CMOS for chip-tochip communications is presented. By leveraging the fractional-N synthesizer technique, this architecture provides a digitally-controlled delay adjustment with a fine resolution and infinite range. The provided delay resolution is less sensitive to the process, voltage, and temperature variations than conventional techniques. A new [delta][sigma] modulator enables a compact and low-power implementation of this architecture. A simple bang-bang detector is used for phase detection. The prototype operates at a 1.8-V supply voltage with a current consumption of 55 mA. The phase resolution and differential rms clock jitter are 1.4 degrees and 3.6 ps, respectively.by Chun-Ming Hsu.Ph.D

Digital enhancement techniques for fractional-N frequency synthesizers

Meeting the demand for unprecedented connectivity in the era of internet-of-things (IoT) requires extremely energy efficient operation of IoT nodes to extend battery life. Managing the data traffic generated by trillions of such nodes also puts severe energy constraints on the data centers. Clock generators that are essential elements in these systems consume significant power and therefore must be optimized for low power and high performance. The focus of this thesis is on improving the energy efficiency of frequency synthesizers and clocking modules by exploring design techniques at both the architectural and circuit levels. In the first part of this work, a digital fractional-N phase locked loop (FNPLL) that employs a high resolution time-to-digital converter (TDC) and a truly ΔΣ fractional divider to achieve low in-band noise with a wide bandwidth is presented. The fractional divider employs a digital-to-time converter (DTC) to cancel out ΔΣ quantization noise in time domain, thus alleviating TDC dynamic range requirements. The proposed digital architecture adopts a narrow range low-power time-amplifier based TDC (TA-TDC) to achieve sub 1ps resolution. Fabricated in 65nm CMOS process, the prototype PLL achieves better than -106dBc/Hz in-band noise and 3MHz PLL bandwidth at 4.5GHz output frequency using 50MHz reference. The PLL achieves excellent jitter performance of 490fsrms, while consumes only 3.7mW. This translates to the best reported jitter-power figure-of-merit (FoM) of -240.5dB among previously reported FNPLLs. Phase noise performance of ring oscillator based digital FNPLLs is severely compromised by conflicting bandwidth requirements to simultaneously suppress oscillator phase and quantization noise introduced by the TDC, ΔΣ fractional divider, and digital-to-analog converter (DAC). As a consequence, their FoM that quantifies the power-jitter tradeoff is at least 25dB worse than their LC-oscillator based FNPLL counterparts. In the second part of this thesis, we seek to close this performance gap by extending PLL bandwidth using quantization noise cancellation techniques and by employing a dual-path digital loop filter to suppress the detrimental impact of DAC quantization noise. A prototype was implemented in a 65nm CMOS process operating over a wide frequency range of 2.0GHz-5.5GHz using a modified extended range multi-modulus divider with seamless switching. The proposed digital FNPLL achieves 1.9psrms integrated jitter while consuming only 4mW at 5GHz output. The measured in-band phase noise is better than -96 dBc/Hz at 1MHz offset. The proposed FNPLL achieves wide bandwidth up to 6MHz using a 50 MHz reference and its FoM is -228.5dB, which is at about 20dB better than previously reported ring-based digital FNPLLs. In the third part, we propose a new multi-output clock generator architecture using open loop fractional dividers for system-on-chip (SoC) platforms. Modern multi-core processors use per core clocking, where each core runs at its own speed. The core frequency can be changed dynamically to optimize for performance or power dissipation using a dynamic frequency scaling (DFS) technique. Fast frequency switching is highly desirable as long as it does not interrupt code execution; therefore it requires smooth frequency transitions with no undershoots. The second main requirement in processor clocking is the capability of spread spectrum frequency modulation. By spreading the clock energy across a wide bandwidth, the electromagnetic interference (EMI) is dramatically reduced. A conventional PLL clock generation approach suffers from a slow frequency settling and limited spread spectrum modulation capabilities. The proposed open loop fractional divider architecture overcomes the bandwidth limitation in fractional-N PLLs. The fractional divider switches the output frequency instantaneously and provides an excellent spread spectrum performance, where precise and programmable modulation depth and frequency can be applied to satisfy different EMI requirements. The fractional divider has unlimited modulation bandwidth resulting in spread spectrum modulation with no filtering, unlike fractional-N PLL; consequently it achieves higher EMI reduction. A prototype fractional divider was implemented in a 65nm CMOS process, where the measured peak-to-peak jitter is less than 27ps over a wide frequency range from 20MHz to 1GHz. The total power consumption is about 3.2mW for 1GHz output frequency. The all-digital implementation of the divider occupies the smallest area of 0.017mm2 compared to state-of-the-art designs. As the data rate of serial links goes higher, the jitter requirements of the clock generator become more stringent. Improving the jitter performance of conventional PLLs to less than (200fsrms) always comes with a large power penalty (tens of mWs). This is due to the PLL coupled noise bandwidth trade-off, which imposes stringent noise requirements on the oscillator and/or loop components. Alternatively, an injection-locked clock multiplier (ILCM) provides many advantages in terms of phase noise, power, and area compared to classical PLLs, but they suffer from a narrow lock-in range and a high sensitivity to PVT variations especially at a large multiplication factor (N). In the fourth part of this thesis, a low-jitter, low-power LC-based ILCM with a digital frequency-tracking loop (FTL) is presented. The proposed FTL relies on a new pulse gating technique to continuously tune the oscillator's free-running frequency. The FTL ensures robust operation across PVT variations and resolves the race condition existing in injection locked PLLs by decoupling frequency tuning from the injection path. As a result, the phase locking condition is only determined by the injection path. This work also introduces an accurate theoretical large-signal analysis for phase domain response (PDR) of injection locked oscillators (ILOs). The proposed PDR analysis captures the asymmetric nature of ILO's lock-in range, and the impact of frequency error on injection strength and phase noise performance. The proposed architecture and analysis are demonstrated by a prototype fabricated in 65 nm CMOS process with active area of 0.25mm2. The prototype ILCM multiplies the reference frequency by 64 to generate an output clock in the range of 6.75GHz-8.25GHz. A superior jitter performance of 190fsrms is achieved, while consuming only 2.25mW power. This translates to a best FoM of -251dB. Unlike conventional PLLs, ILCMs have been fundamentally limited to only integer-N operation and cannot synthesize fractional-N frequencies. In the last part of this thesis, we extend the merits of ILCMs to fractional-N and overcome this fundamental limitation. We employ DTC-based QNC techniques in order to align injected pulses to the oscillator's zero crossings, which enables it to pull the oscillator toward phase lock, thus realizing a fractional-N ILCM. Fabricated in 65nm CMOS process, a prototype 20-bit fractional-N ILCM with an output range of 6.75GHz-8.25GHz consumes only 3.25mW. It achieves excellent jitter performance of 110fsrms and 175fsrms in integer- and fractional-N modes respectively, which translates to the best-reported FoM in both integer- (-255dB) and fractional-N (-252dB) modes. The proposed fractional-N ILCM also features the first-reported rapid on/off capability, where the transient absolute jitter performance at wake-up is bounded below 4ps after less than 4ns. This demonstrates almost instantaneous phase settling. This unique capability enables tremendous energy saving by turning on the clock multiplier only when needed. This energy proportional operation leverages idle times to save power at the system-level of wireline and wireless transceivers

Design of high performance frequency synthesizers in communication systems

Frequency synthesizer is a key building block of fully-integrated wireless communication systems. Design of a frequency synthesizer requires the understanding of not only the circuit-level but also of the transceiver system-level considerations. This dissertation presents a full cycle of the synthesizer design procedure starting from the interpretation of standards to the testing and measurement results. A new methodology of interpreting communication standards into low level circuit specifications is developed to clarify how the requirements are calculated. A detailed procedure to determine important design variables is presented incorporating the fundamental theory and non-ideal effects such as phase noise and reference spurs. The design procedure can be easily adopted for different applications. A BiCMOS frequency synthesizer compliant for both wireless local area network (WLAN) 802.11a and 802.11b standards is presented as a design example. The two standards are carefully studied according to the proposed standard interpretation method. In order to satisfy stringent requirements due to the multi-standard architecture, an improved adaptive dual-loop phase-locked loop (PLL) architecture is proposed. The proposed improvements include a new loop filter topology with an active capacitance multiplier and a tunable dead zone circuit. These improvements are crucial for monolithic integration of the synthesizer with no off-chip components. The proposed architecture extends the operation limit of conventional integerN type synthesizers by providing better reference spur rejection and settling time performance while making it more suitable for monolithic integration. It opens a new possibility of using an integer-N architecture for various other communication standards, while maintaining the benefit of the integer-N architecture; an optimal performance in area and power consumption

Time-Mode Analog Circuit Design for Nanometric Technologies

Rapid scaling in technology has introduced new challenges in the realm of traditional analog design. Scaling of supply voltage directly impacts the available voltage-dynamic-range. On the other hand, nanometric technologies with fT in the hundreds of GHz range open opportunities for time-resolution-based signal processing. With reduced available voltage-dynamic-range and improved timing resolution, it is more convenient to devise analog circuits whose performance depends on edge-timing precision rather than voltage levels. Thus, instead of representing the data/information in the voltage-mode, as a difference between two node voltages, it should be represented in time-mode as a time-difference between two rising and/or falling edges. This dissertation addresses the feasibility of employing time-mode analog circuit design in different applications. Specifically: 1) Time-mode-based quanitzer and feedback DAC of SigmaDelta ADC. 2) Time-mode-based low-THD 10MHz oscillator, 3) A Spur-Frequency Boosting PLL with -74dBc Reference-Spur Rejection in 90nm Digital CMOS. In the first project, a new architectural solution is proposed to replace the DAC and the quantizer by a Time-to-Digital converter. The architecture has been fabricated in 65nm and shows that this technology node is capable of achieving a time-matching of 800fs which has never been reported. In addition, a competitive figure-of-merit is achieved. In the low-THD oscillator, I proposed a new architectural solution for synthesizing a highly-linear sinusoidal signal using a novel harmonic rejection approach. The chip is fabricated in 130nm technology and shows an outstanding performance compared to the state of the art. The designed consumes 80% less power; consumes less area; provides much higher amplitude while being composed of purely digital circuits and passive elements. Last but not least, the spur-frequency boosting PLL employs a novel technique that eliminates the reference spurs. Instead of adding additional filtering at the reference frequency, the spur frequency is boosted to higher frequency which is, naturally, has higher filtering effects. The prototype is fabricated in 90nm digital CMOS and proved to provide the lowest normalized reference spurs ever reported