Channel-Stacked NAND Flash Memory with High-κ Charge Trapping Layer for High Scalability

학위논문 (박사)-- 서울대학교 대학원 : 전기·컴퓨터공학부, 2016. 2. 박병국.Exploding demands for mobile devices induce the drastic expansion of the market of NAND flash memory as high density storage devices. Three-dimensional (3D) NAND flash memory paved a new way of increasing the memory capacity by stacking cells in three-dimension. For stacked NAND flash memory, the thickness of ONO (memory dielectric layers) is a roadblock in scaling-down of the minimum feature size, because channel diameter can be scaled down to < 20 nm. However, it is challenging to reduce the thickness of oxide-nitride-oxide (ONO) layer, since the charge trapping properties degrade when the Si3N4 is made thinner. .In this thesis, the channel stacked NAND flash memory array (CSTAR) with high-κ charge trapping layer for high scalability is proposed. To adopt high-κ layer into 3D NAND, its memory characteristics were evaluated with capacitors and gate-all-around flash memory devices. Finally, 4-layer channel stacked memory with high-κ layer was successfully fabricated and characterized. Recent trend of nonvolatile memories are introduced and the overview of 3D stacked NAND flash memory technology is presented in Chapter 1 and 2. In Chapter 3, the memory characteristics of high-κ layer were evaluated with fabricated capacitors and flash memory devices. In Chapter 4, fabrication process and electrical characteristics of CSTAR with high-κ are shown. With the comparison with previous works using ONO layer, CSTAR with high-κ is evaluated. In Chapter 5, the novel operation method of CSTAR is presented. Using TCAD and measurement, a newly designed operation method is verifiedChapter 1 Introduction 1 1.1 Flash Memory Technology 1 1.2 Flash Memory Unit Cell and Array Structure 6 1.3 NAND Cell Operation 13 1.4 Charge Trap Flash Memory 25 Chapter 2 3-D Stacked NAND Flash Memory 28 2.2 Examination of Previous 3-D Stacked NAND Flash 28 2.2.1 Gate Stack Type 3-D NAND Flash Memory 28 2.2.2 Channel Stack Type 3-D NAND Flash Memory 36 2.2.3 Comparison between the Gate Stack Type and the Channel Stack Type 45 Chapter 3 Channel Stacked NAND Flash Memory with high- Charge Trapping Layer 48 3.1 Introduction 48 3.2 Memory Characteristics of HfO2 52 3.3 Fabrication of Nanowire Memory Devices with high-κ Dielectric Layer 56 Chapter 4 Fabrication of Channel Stacked NAND Flash Memory with High-κ 66 4.1 Introduction 66 4.2 Fabrication Method 67 4.3 Key Process Steps of CSTAR with high-κ 72 4.3.1 Single Crystalline Silicon Channel 72 4.3.2 Fin Patterning 74 4.3.3 Stacked Nanowires 76 4.4 Measurement Results 81 4.5 Comparison with Previous Works 88 Chapter 5 Novel Program Operation in CSTAR 92 5.1 Introduction. 92 5.2 Simulation Results 93 5.3 Measurement Results 103 Chapter 6 Conclusions 106 Bibliography 108 Abstract in Korean 116 List of Publications 118Docto

Caractérisation, mécanismes et applications mémoire des transistors avancés sur SOI

Ce travail présente les principaux résultats obtenus avec une large gamme de dispositifs SOI avancés, candidats très prometteurs pour les futurs générations de transistors MOSFETs. Leurs propriétés électriques ont été analysées par des mesures systématiques, agrémentées par des modèles analytiques et/ou des simulations numériques. Nous avons également proposé une utilisation originale de dispositifs FinFETs fabriqués sur ONO enterré en fonctionnalisant le ONO à des fins d'application mémoire non volatile, volatile et unifiées. Après une introduction sur l'état de l'art des dispositifs avancés en technologie SOI, le deuxième chapitre a été consacré à la caractérisation détaillée des propriétés de dispositifs SOI planaires ultra- mince (épaisseur en dessous de 7 nm) et multi-grille. Nous avons montré l excellent contrôle électrostatique par la grille dans les transistors très courts ainsi que des effets intéressants de transport et de couplage. Une approche similaire a été utilisée pour étudier et comparer des dispositifs FinFETs à double grille et triple grille. Nous avons démontré que la configuration FinFET double grille améliore le couplage avec la grille arrière, phénomène important pour des applications à tension de seuil multiple. Nous avons proposé des modèles originaux expliquant l'effet de couplage 3D et le comportement de la mobilité dans des TFTs nanocristallin ZnO. Nos résultats ont souligné les similitudes et les différences entre les transistors SOI et à base de ZnO. Des mesures à basse température et de nouvelles méthodes d'extraction ont permis d'établir que la mobilité dans le ZnO et la qualité de l'interface ZnO/SiO2 sont remarquables. Cet état de fait ouvre des perspectives intéressantes pour l'utilisation de ce type de matériaux aux applications innovantes de l'électronique flexible. Dans le troisième chapitre, nous nous sommes concentrés sur le comportement de la mobilité dans les dispositifs SOI planaires et FinFET en effectuant des mesures de magnétorésistance à basse température. Nous avons mis en évidence expérimentalement un comportement de mobilité inhabituel (multi-branche) obtenu lorsque deux ou plusieurs canaux coexistent et interagissent. Un autre résultat original concerne l existence et l interprétation de la magnétorésistance géométrique dans les FinFETs.L'utilisation de FinFETs fabriqués sur ONO enterré en tant que mémoire non volatile flash a été proposée dans le quatrième chapitre. Deux mécanismes d'injection de charge ont été étudiés systématiquement. En plus de la démonstration de la pertinence de ce type mémoire en termes de performances (rétention, marge de détection), nous avons mis en évidence un comportement inattendu : l amélioration de la marge de détection pour des dispositifs à canaux courts. Notre concept innovant de FinFlash sur ONO enterré présente plusieurs avantages: (i) opération double-bit et (ii) séparation de la grille de stockage et de l'interface de lecture augmentant la fiabilité et autorisant une miniaturisation plus poussée que des Finflash conventionnels avec grille ONO.Dans le dernier chapitre, nous avons exploré le concept de mémoire unifiée, en combinant les opérations non volatiles et 1T-DRAM par le biais des FinFETs sur ONO enterré. Comme escompté pour les mémoires dites unifiées, le courant transitoire en mode 1T-DRAM dépend des charges non volatiles stockées dans le ONO. D'autre part, nous avons montré que les charges piégées dans le nitrure ne sont pas perturbées par les opérations de programmation et lecture de la 1T-DRAM. Les performances de cette mémoire unifiée multi-bits sont prometteuses et pourront être considérablement améliorées par optimisation technologique de ce dispositif.The evolution of electronic systems and portable devices requires innovation in both circuit design and transistor architecture. During last fifty years, the main issue in MOS transistor has been the gate length scaling down. The reduction of power consumption together with the co-integration of different functions is a more recent avenue. In bulk-Si planar technology, device shrinking seems to arrive at the end due to the multiplication of parasitic effects. The relay has been taken by novel SOI-like device architectures. In this perspective, this manuscript presents the main achievements of our work obtained with a variety of advanced fully depleted SOI MOSFETs, which are very promising candidates for next generation MOSFETs. Their electrical properties have been analyzed by systematic measurements and clarified by analytical models and/or simulations. Ultimately, appropriate applications have been proposed based on their beneficial features.In the first chapter, we briefly addressed the short-channel effects and the diverse technologies to improve device performance. The second chapter was dedicated to the detailed characterization and interesting properties of SOI devices. We have demonstrated excellent gate control and high performance in ultra-thin FD SOI MOSFET. The SCEs are efficiently suppressed by decreasing the body thickness below 7 nm. We have investigated the transport and electrostatic properties as well as the coupling mechanisms. The strong impact of body thickness and temperature range has been outlined. A similar approach was used to investigate and compare vertical double-gate and triple-gate FinFETs. DG FinFETs show enhanced coupling to back-gate bias which is applicable and suitable for dynamic threshold voltage tuning. We have proposed original models explaining the 3D coupling effect in FinFETs and the mobility behavior in ZnO TFTs. Our results pointed on the similarities and differences in SOI and ZnO transistors. According to our low-temperature measurements and new promoted extraction methods, the mobility in ZnO and the quality of ZnO/SiO2 interface are respectable, enabling innovating applications in flexible, transparent and power electronics. In the third chapter, we focused on the mobility behavior in planar SOI and FinFET devices by performing low-temperature magnetoresistance measurements. Unusual mobility curve with multi-branch aspect were obtained when two or more channels coexist and interplay. Another original result in the existence of the geometrical magnetoresistance in triple-gate and even double-gate FinFETs.The operation of a flash memory in FinFETs with ONO buried layer was explored in the forth chapter. Two charge injection mechanisms were proposed and systematically investigated. We have discussed the role of device geometry and temperature. Our novel ONO FinFlash concept has several distinct advantages: double-bit operation, separation of storage medium and reading interface, reliability and scalability. In the final chapter, we explored the avenue of unified memory, by combining nonvolatile and 1T-DRAM operations in a single transistor. The key result is that the transient current, relevant for 1T-DRAM operation, depends on the nonvolatile charges stored in the nitride buried layer. On the other hand, the trapped charges are not disturbed by the 1T-DRAM operation. Our experimental data offers the proof-of-concept for such advanced memory. The performance of the unified/multi-bit memory is already decent but will greatly improve in the coming years by processing dedicated devices.SAVOIE-SCD - Bib.électronique (730659901) / SudocGRENOBLE1/INP-Bib.électronique (384210012) / SudocGRENOBLE2/3-Bib.électronique (384219901) / SudocSudocFranceF

Miniaturized Transistors, Volume II

In this book, we aim to address the ever-advancing progress in microelectronic device scaling. Complementary Metal-Oxide-Semiconductor (CMOS) devices continue to endure miniaturization, irrespective of the seeming physical limitations, helped by advancing fabrication techniques. We observe that miniaturization does not always refer to the latest technology node for digital transistors. Rather, by applying novel materials and device geometries, a significant reduction in the size of microelectronic devices for a broad set of applications can be achieved. The achievements made in the scaling of devices for applications beyond digital logic (e.g., high power, optoelectronics, and sensors) are taking the forefront in microelectronic miniaturization. Furthermore, all these achievements are assisted by improvements in the simulation and modeling of the involved materials and device structures. In particular, process and device technology computer-aided design (TCAD) has become indispensable in the design cycle of novel devices and technologies. It is our sincere hope that the results provided in this Special Issue prove useful to scientists and engineers who find themselves at the forefront of this rapidly evolving and broadening field. Now, more than ever, it is essential to look for solutions to find the next disrupting technologies which will allow for transistor miniaturization well beyond silicon’s physical limits and the current state-of-the-art. This requires a broad attack, including studies of novel and innovative designs as well as emerging materials which are becoming more application-specific than ever before

Miniaturized Transistors

What is the future of CMOS? Sustaining increased transistor densities along the path of Moore's Law has become increasingly challenging with limited power budgets, interconnect bandwidths, and fabrication capabilities. In the last decade alone, transistors have undergone significant design makeovers; from planar transistors of ten years ago, technological advancements have accelerated to today's FinFETs, which hardly resemble their bulky ancestors. FinFETs could potentially take us to the 5-nm node, but what comes after it? From gate-all-around devices to single electron transistors and two-dimensional semiconductors, a torrent of research is being carried out in order to design the next transistor generation, engineer the optimal materials, improve the fabrication technology, and properly model future devices. We invite insight from investigators and scientists in the field to showcase their work in this Special Issue with research papers, short communications, and review articles that focus on trends in micro- and nanotechnology from fundamental research to applications

Caractérisation électrique de transistors à effet de champ avancés : transistors sans jonctions, sur réseaux de nanotubes de carbone ou sur nanofil en oxyde d'étain

In this dissertation, the electrical characterization of heavily-doped junctionless transistors (JLTs) and individual tin-oxide (SnO2) nanowire field-effect transistors (FETs) and single-walled carbon nanotube (SWCNT) random network thin film transistors (RN-TFTs) are presented in terms of I-V, C-V, low frequency noise (LFN), and low temperature measurement including a numerical simulation, respectively. As a potential emerging candidate for more than Moore, recently developed heavily doped JLTs were studied in low-temperature (77K ~ 350K) with double gate mode to have physical insights of carrier scattering mechanism with account for both the position of flat-band voltage and doping concentration, respectively. Besides, as a nano-scaled bottom-up device, polymethyl methacrylate passivated individual SnO2 nanowire FET was discussed. A large contribution of channel access resistance to carrier mobility and LFN behavior was found as same as in nano-structure devices. Furthermore, various electrical characteristics of percolation dominant N-type SWCNT RN-TFTs were demonstrated by taking into account for I-V, C-V, LFN and a numerical percolation simulation.Les matériaux de faible dimensionnalité, tels que les nanotubes de carbone, le graphène, les nanofils de semi-conducteurs ou d'oxydes métalliques, présentent des propriétés intéressantes telles qu'un rapport surface/ volume important, des mobilités électroniques élevées, des propriétés thermiques et électriques particulières, avec la possibilité de constituer une alternatives à certaines fonctions CMOS ou d'intégrer de nouvelles fonctions comme la récupération d'énergie ou des capteurs. Pour la bio-détection, les nanofils permettent par exemple d'obtenir une grande sensibilité à la présence de biomolécules cibles grâce à la modification de charge qui accompagne leur hybridation sur des biomolécules sondes greffées à la surface du nanofil et au fort couplage électrostatique de cette charge de surface avec le cœur du nanofil. La fabrication de ce type de structure suit différentes voies: une voie dite "top-down" qui est utilisée par la production microélectronique de masse et qui permet un excellent contrôle technologique grâce à l'utilisation d'équipements, notamment de lithographie, extrêmement performants; une seconde voie moins coûteuse mais moins contrôlée dite "bottom-up" dont un exemple répandu est la réalisation de réseaux aléatoires, obtenus par dispersion de nanostructures réalisées directement sous forme 1D par croissance et en général relativement dopés de façon non nécessairement contrôlée. Dans les deux cas, le mécanisme de base est le contrôle électrostatique du canal par effet de champ d'un ensemble (organisé ou non) de nanostructures. Dans cette thèse, trois types de transistors différents sont explorées ; des transistors à nanofils SnO2, des réseaux aléatoires de nanotubes de carbone, des transistors à nanofil à canal uniformément dopé, dits "junctionless transistors" ou JLTs). Par rapport à la configuration classique d'un transistor MOS à inversion, le contrôle demande en général à être reconsidéré pour tenir compte des spécificités de ce type de structures: topologie du canal, isolants non standards (résines), effets de percolation dans les réseaux désordonné, contrôle électrostatique dans les nanofils fortement dopés, rôle crucial des états d'interface. Le travail s'appuie sur (i) une caractérisation approfondie de ces composants en statique (contrôle du courant), en petit signal (contrôle de la charge) et en bruit (pièges et états d'interfaces), (ii) une analyse critique des méthodologies d'extraction de paramètres et des modèles utilisés pour analyser ce fonctionnement avec dans certains cas l'appui de simulations et (iii) le développement, lorsque cela s'avère nécessaire, de nouvelles méthodologies d'extraction

A study of silicon and germanium junctionless transistors

Technology boosters, such as strain, HKMG and FinFET, have been introduced into semiconductor industry to extend Moore’s law beyond 130 nm technology nodes. New device structures and channel materials are highly demanded to keep performance enhancement when the device scales beyond 22 nm. In this work, the properties and feasibility of the proposed Junctionless transistor (JNT) have been evaluated for both Silicon and Germanium channels. The performance of Silicon JNTs with 22 nm gate length have been characterized at elevated temperature and stressed conditions. Furthermore, steep Subthreshold Slopes (SS) in JNT and IM devices are compared. It is observed that the floating body in JNT is relatively dynamic comparing with that in IM devices and proper design of the device structure may further reduce the VD for a sub- 60 mV/dec subthreshold slope. Diode configuration of the JNT has also been evaluated, which demonstrates the first diode without junctions. In order to extend JNT structure into the high mobility material Germanium (Ge), a full process has been develop for Ge JNT. Germanium-on-Insulator (GeOI) wafers were fabricated using Smart-Cut with low temperature direct wafer bonding method. Regarding the lithography and pattern transfer, a top-down process of sub-50-nm width Ge nanowires is developed in this chapter and Ge nanowires with 35 nm width and 50 nm depth are obtained. The oxidation behaviour of Ge by RTO has been investigated and high-k passivation scheme using thermally grown GeO2 has been developed. With all developed modules, JNT with Ge channels have been fabricated by the CMOScompatible top-down process. The transistors exhibit the lowest subthreshold slope to date for Ge JNT. The devices with a gate length of 3 μm exhibit a SS of 216 mV/dec with an ION/IOFF current ratio of 1.2×103 at VD = -1 V and DIBL of 87 mV/V

Tunnel Field Effect Transistors:from Steep-Slope Electronic Switches to Energy Efficient Logic Applications

The aim of this work has been the investigation of homo-junction Tunnel Field Effect Transistors starting from a compact modelling perspective to its possible applications. Firstly a TCAD based simulation study is done to explain the main device characteristics. The main differences of a Tunnel FET with respect to a conventional MOSFET is pointed out and the differences have been explained. A compact DC/AC model has been developed which is capable of describing the I-V characteristics in all regimes of operation. The model takes in to account ambi-polarity, drain side breakdown and all tunneling related physics. A temperature dependence is also added to the model to study the temperature independent behavior of tunneling. The model was further implemented in a Verilog-A based circuit simulator. Following calibration to experimental results of Silicon and strained-Silicon TFETs, the model has been also used to benchmark against a standard CMOS node for digital and analog applications. The circuits built with Tunnel FETs showed interesting temperature behavior which was superior to the compared CMOS node. In the same work, we also explore and propose solutions for using TFETs for low power memory applications. Both volatile and non-volatile memory concepts are investigated and explored. The application of a Tunnel FET as a capacitor-less memory has been experimentally demonstrated for the first time. New device concepts have been proposed and process flows for the same are developed to realize them in the clean room in EPFL

Semiconductor Memory Devices for Hardware-Driven Neuromorphic Systems

This book aims to convey the most recent progress in hardware-driven neuromorphic systems based on semiconductor memory technologies. Machine learning systems and various types of artificial neural networks to realize the learning process have mainly focused on software technologies. Tremendous advances have been made, particularly in the area of data inference and recognition, in which humans have great superiority compared to conventional computers. In order to more effectively mimic our way of thinking in a further hardware sense, more synapse-like components in terms of integration density, completeness in realizing biological synaptic behaviors, and most importantly, energy-efficient operation capability, should be prepared. For higher resemblance with the biological nervous system, future developments ought to take power consumption into account and foster revolutions at the device level, which can be realized by memory technologies. This book consists of seven articles in which most recent research findings on neuromorphic systems are reported in the highlights of various memory devices and architectures. Synaptic devices and their behaviors, many-core neuromorphic platforms in close relation with memory, novel materials enabling the low-power synaptic operations based on memory devices are studied, along with evaluations and applications. Some of them can be practically realized due to high Si processing and structure compatibility with contemporary semiconductor memory technologies in production, which provides perspectives of neuromorphic chips for mass production

Modelling and simulation study of NMOS Si nanowire transistors

Nanowire transistors (NWTs) represent a potential alternative to Silicon FinFET technology in the 5nm CMOS technology generation and beyond. Their gate length can be scaled beyond the limitations of FinFET gate length scaling to maintain superior off-state leakage current and performance thanks to better electrostatic control through the semiconductor nanowire channels by gate-all-around (GAA) architecture. Furthermore, it is possible to stack nanowires to enhance the drive current per footprint. Based on these considerations, vertically-stacked lateral NWTs have been included in the latest edition of the International Technology Roadmap for Semiconductors (ITRS) to allow for further performance enhancement and gate pitch scaling, which are key criteria of merit for the new CMOS technology generation. However, electrostatic confinement and the transport behaviour in these devices are more complex, especially in or beyond the 5nm CMOS technology generation. At the heart of this thesis is the model-based research of aggressively-scaled NWTs suitable for implementation in or beyond the 5nm CMOS technology generation, including their physical and operational limitations and intrinsic parameter fluctuations. The Ensemble Monte Carlo approach with Poisson-Schrödinger (PS) quantum corrections was adopted for the purpose of predictive performance evaluation of NWTs. The ratio of the major to the minor ellipsoidal cross-section axis (cross-sectional aspect ratio - AR) has been identified as a significant contributing factor in device performance. Until now, semiconductor industry players have carried out experimental research on NWTs with two different cross-sections: circular cylinder (or elliptical) NWTs and nanosheet (or nanoslab) NWTs. Each version has its own benefits and drawbacks; however, the key difference between these two versions is the cross-sectional AR. Several critical design questions, including the optimal NWT cross-sectional aspect ratio, remain unanswered. To answer these questions, the AR of a GAA NWT has been investigated in detail in this research maintaining the cross-sectional area constant. Signatures of isotropic charge distributions within Si NWTs were observed, exhibiting the same attributes as the golden ratio (Phi), the significance of which is well-known in the fields of art and architecture. To address the gap in the existing literature, which largely explores NWT scaling using single-channel simulation, thorough simulations of multiple channels vertically-stacked NWTs have been carried out with different cross-sectional shapes and channel lengths. Contact resistance, non-equilibrium transport and quantum confinement effects have been taken into account during the simulations in order to realistically access performance and scalability. Finally, the individual and combined effects of key statistical variability (SV) sources on threshold voltage (VT), subthreshold slope (SS), ON-current (Ion) and drain-induced barrier lowering (DIBL) have been simulated and discussed. The results indicate that the variability of NWTs is impacted by device architecture and dimensions, with a significant reduction in SV found in NWTs with optimal aspect ratios. Furthermore, a reduction in the variability of the threshold voltage has been observed in vertically-stacked NWTs due to the cancelling-out of variability in double and triple lateral channel NWTs