Analysis of two level and three level inverters

The power electronics device which converts DC power to AC power at required output voltage and frequency level is known as inverter. Inverters can be broadly classified into single level inverter and multilevel inverter. Multilevel inverter as compared to single level inverters have advantages like minimum harmonic distortion, reduced MI/RFI generation and can operate on several voltage levels. A multi-stage inverter is being utilized for multipurpose applications, such as active power filters, static var compensators and machine drives for sinusoidal and trapezoidal current applications. The drawbacks are the isolated power supplies required for each one of the stages of the multiconverter and it’s also lot harder to build, more expensive, harder to control in software. This project aims at the simulation study of three phase single level and multilevel inverters. The role of inverters in active power filter for harmonic filtering is studied and simulated in MATLAB/SIMULINK. Firstly, the three phase system with non-linear loads are modeled and their characteristics is observed . Secondly, the active power filters are modeled with the inverters and suitable switching control strategies ( PWM technique) to carry out harmonic elimination

Networking Aspects based on the Talkative Power Concept for DC Microgrid Systems

The talkative power concept is a simultaneous power-line communication and energy transfer technique which integrates data modulation into a power converter. The information sequence is deterministically represented by the ripple, which superimposes the output voltage. With a few exceptions, so far emphasis has been on scenarios where only a single node is actively transmitting data in a certain time slot in simplex mode. In microgrid applications, however, multiple active power sources are of interest as well. Examples include battery management systems, smart metering, electricity trading systems, and smart grids with several power sources, energy storage devices, loads, and data receivers. In this contribution, bus networking aspects based on the talkative power concept are presented for scenarios with several active nodes and for full-duplex communication. The paper addresses potential multiple access techniques as well as duplexing schemes for connected power converters supporting bidirectional power and information flow. In numerical results, a spread spectrum scheme based on orthogonal variable spreading factor codes in conjunction with frequency shift keying (FSK) is presented for four simultaneously active buck converters with a sum data rate of 500 kbps at a switching frequency of 1 MHz. In general, with 2-ary FSK, the maximum achievable sum data rate is half of the switching frequency in a synchronous setup

Study of switching transients in high frequency converters

As the semiconductor technologies progress rapidly, the power densities and switching frequencies of many power devices are improved. With the existing technology, high frequency power systems become possible. Use of such a system is advantageous in many aspects. A high frequency ac source is used as the direct input to an ac/ac pulse-density-modulation (PDM) converter. This converter is a new concept which employs zero voltage switching techniques. However, the development of this converter is still in its infancy stage. There are problems associated with this converter such as a high on-voltage drop, switching transients, and zero-crossing detecting. Considering these problems, the switching speed and power handling capabilities of the MOS-Controlled Thyristor (MCT) makes the device the most promising candidate for this application. A complete insight of component considerations for building an ac/ac PDM converter for a high frequency power system is addressed. A power device review is first presented. The ac/ac PDM converter requires switches that can conduct bi-directional current and block bi-directional voltage. These bi-directional switches can be constructed using existing power devices. Different bi-directional switches for the converter are investigated. Detailed experimental studies of the characteristics of the MCT under hard switching and zero-voltage switching are also presented. One disadvantage of an ac/ac converter is that turn-on and turn-off of the switches has to be completed instantaneously when the ac source is at zero voltage. Otherwise shoot-through current or voltage spikes can occur which can be hazardous to the devices. In order for the devices to switch softly in the safe operating area even under non-ideal cases, a unique snubber circuit is used in each bi-directional switch. Detailed theory and experimental results for circuits using these snubbers are presented. A current regulated ac/ac PDM converter built using MCT's and IGBT's is evaluated

Z-domain modeling of peak current mode control for full-bridge DC-DC buck converters

Traditional local-averaged state-space modeling for peak current mode (PCM) controls fails to explain the subharmonic oscillation phenomenon when the spectrum is higher than half of the switching frequency. To address this problem, this paper presents a small-signal modeling method in the z-domain, and builds a discrete linear model for the current loop of a full-bridge DC-DC converter. This discrete model is converted into a second-order continuous model that is able to represent the system performance with a wider frequency range. A frequency-domain analysis shows that this model can be used to explain the subharmonic oscillations and unstable characteristics. This provides an engineering guideline for the practical design of slope compensation. The effectiveness of the proposed modeling method has been verified by simulation and experimental results with a prototype working in the Buck mode

Universal fractional-order design of linear phase lead compensation multirate repetitive control for PWM inverters

Repetitive control (RC) with linear phase lead compensation provides a simple but very effective control solution for any periodic signal with a known period. Multirate repetitive control (MRC) with a downsampling rate can reduce the need of memory size and computational cost, and then leads to a more feasible design of the plug-in repetitive control systems in practical applications. However, with fixed sampling rate, both MRC and its linear phase lead compensator are sensitive to the ratio of the sampling frequency to the frequency of interested periodic signals: (1) MRC might fails to exactly compensate the periodic signal in the case of a fractional ratio; (2) linear phase lead compensation might fail to enable MRC to achieve satisfactory performance in the case of a low ratio. In this paper, a universal fractional-order design of linear phase lead compensation MRC is proposed to tackle periodic signals with high accuracy, fast dynamic response, good robustness, and cost-effective implementation regardless of the frequency ratio, which offers a unified framework for housing various RC schemes in extensive engineering application. An application example of programmable AC power supply is explored to comprehensively testify the effectiveness of the proposed control scheme

DC power line communication based on power/signal dual modulation in phase shift full bridge converters

For intelligent DC distributed power systems, data communication plays a vital role in system control and device monitoring. To achieve communication in a cost effective way, power/signal dual modulation (PSDM), a method that integrates data transmission with power conversion, can be utilized. In this paper, an improved PSDM method using phase shift full bridge (PSFB) converter is proposed. This method introduces a phase control based freedom in the conventional PSFB control loop to realize communication using the same power conversion circuit. In this way, decoupled data modulation and power conversion are realized without extra wiring and coupling units, and thus the system structure is simplified. More importantly, the signal intensity can be regulated by the proposed perturbation depth, and so this method can adapt to different operating conditions. Application of the proposed method to a DC distributed power system composed of several PSFB converters is discussed. A 2kW prototype system with an embedded 5kbps communication link has been implemented, and the effectiveness of the method is verified by experimental results

A 6.0-mW 10.0-Gb/s Receiver With Switched-Capacitor Summation DFE

A low-power receiver with a one-tap decision feedback equalization (DFE) was fabricated in 90-nm CMOS technology. The speculative equalization is performed using switched-capacitor-based addition at the front-end sample-hold circuit. In order to further reduce the power consumption, an analog multiplexer is used in the speculation technique implementation. A quarter-rate-clocking scheme facilitates the use of low-power front-end circuitry and CMOS clock buffers. The receiver was tested over channels with different levels of ISI. The signaling rate with BER<10^-12 was significantly increased with the use of DFE for short- to medium-distance PCB traces. At 10-Gb/s data rate, the receiver consumes less than 6.0 mW from a 1.0-V supply. This includes the power consumed in all quarter-rate clock buffers, but not the power of a clock recovery loop. The input clock phase and the DFE taps are adjusted externally