An efficient design of embedded memories and their testability analysis using Markov chains

This article presents a design strategy for efficient and comprehensive random testing of embedded random-access memory (RAM) where neither are the address, read/write and data input lines directly controllable nor are the data output lines externally observable. Unlike the conventional approaches, which frequently employ on-chip circuits such as linear feedback shift register (LFSR), data registers and multibit comparator for verifying the response of the memory-under-test (MUT) with the reference signature of a fault-free gold unit , the proposed technique uses an efficient testable design, which helps accelerate test algorithms by a factor of 0.5√ n , if the RAM is organized into an n ×1 array and improve the test reliability by eliminating the LFSR that is known to have aliasing problems. Another serious problem in embedded memory testing by random test patterns is the problem of memory initialization, which has been tackled here by adding word-line flag registers. The paper has made indepth empirical studies of the functional faults such as stuck-at, coupling, and pattern-sensitive by suitably representing these faults by Markov chains and by simulating these chains to derive various test lengths required for detecting these faults. The simulation results conclusively show that, in order to test a IM-bit RAM for detecting the common functional faults, the proposed technique needs only one second as opposed to about an hour needed by the conventional random testing where memory cells are tested sequentially.Peer Reviewedhttp://deepblue.lib.umich.edu/bitstream/2027.42/43013/1/10836_2004_Article_BF00134733.pd

On Information-centric Resiliency and System-level Security in Constrained, Wireless Communication

The Internet of Things (IoT) interconnects many heterogeneous embedded devices either locally between each other, or globally with the Internet. These things are resource-constrained, e.g., powered by battery, and typically communicate via low-power and lossy wireless links. Communication needs to be secured and relies on crypto-operations that are often resource-intensive and in conflict with the device constraints. These challenging operational conditions on the cheapest hardware possible, the unreliable wireless transmission, and the need for protection against common threats of the inter-network, impose severe challenges to IoT networks. In this thesis, we advance the current state of the art in two dimensions. Part I assesses Information-centric networking (ICN) for the IoT, a network paradigm that promises enhanced reliability for data retrieval in constrained edge networks. ICN lacks a lower layer definition, which, however, is the key to enable device sleep cycles and exclusive wireless media access. This part of the thesis designs and evaluates an effective media access strategy for ICN to reduce the energy consumption and wireless interference on constrained IoT nodes. Part II examines the performance of hardware and software crypto-operations, executed on off-the-shelf IoT platforms. A novel system design enables the accessibility and auto-configuration of crypto-hardware through an operating system. One main focus is the generation of random numbers in the IoT. This part of the thesis further designs and evaluates Physical Unclonable Functions (PUFs) to provide novel randomness sources that generate highly unpredictable secrets, on low-cost devices that lack hardware-based security features. This thesis takes a practical view on the constrained IoT and is accompanied by real-world implementations and measurements. We contribute open source software, automation tools, a simulator, and reproducible measurement results from real IoT deployments using off-the-shelf hardware. The large-scale experiments in an open access testbed provide a direct starting point for future research

Infrastructures and Algorithms for Testable and Dependable Systems-on-a-Chip

Every new node of semiconductor technologies provides further miniaturization and higher performances, increasing the number of advanced functions that electronic products can offer. Silicon area is now so cheap that industries can integrate in a single chip usually referred to as System-on-Chip (SoC), all the components and functions that historically were placed on a hardware board. Although adding such advanced functionality can benefit users, the manufacturing process is becoming finer and denser, making chips more susceptible to defects. Today’s very deep-submicron semiconductor technologies (0.13 micron and below) have reached susceptibility levels that put conventional semiconductor manufacturing at an impasse. Being able to rapidly develop, manufacture, test, diagnose and verify such complex new chips and products is crucial for the continued success of our economy at-large. This trend is expected to continue at least for the next ten years making possible the design and production of 100 million transistor chips. To speed up the research, the National Technology Roadmap for Semiconductors identified in 1997 a number of major hurdles to be overcome. Some of these hurdles are related to test and dependability. Test is one of the most critical tasks in the semiconductor production process where Integrated Circuits (ICs) are tested several times starting from the wafer probing to the end of production test. Test is not only necessary to assure fault free devices but it also plays a key role in analyzing defects in the manufacturing process. This last point has high relevance since increasing time-to-market pressure on semiconductor fabrication often forces foundries to start volume production on a given semiconductor technology node before reaching the defect densities, and hence yield levels, traditionally obtained at that stage. The feedback derived from test is the only way to analyze and isolate many of the defects in today’s processes and to increase process’s yield. With the increasing need of high quality electronic products, at each new physical assembly level, such as board and system assembly, test is used for debugging, diagnosing and repairing the sub-assemblies in their new environment. Similarly, the increasing reliability, availability and serviceability requirements, lead the users of high-end products performing periodic tests in the field throughout the full life cycle. To allow advancements in each one of the above scaling trends, fundamental changes are expected to emerge in different Integrated Circuits (ICs) realization disciplines such as IC design, packaging and silicon process. These changes have a direct impact on test methods, tools and equipment. Conventional test equipment and methodologies will be inadequate to assure high quality levels. On chip specialized block dedicated to test, usually referred to as Infrastructure IP (Intellectual Property), need to be developed and included in the new complex designs to assure that new chips will be adequately tested, diagnosed, measured, debugged and even sometimes repaired. In this thesis, some of the scaling trends in designing new complex SoCs will be analyzed one at a time, observing their implications on test and identifying the key hurdles/challenges to be addressed. The goal of the remaining of the thesis is the presentation of possible solutions. It is not sufficient to address just one of the challenges; all must be met at the same time to fulfill the market requirements

Investigation into the wafer-scale integration of fine-grain parallel processing computer systems

This thesis was submitted for the degree of Doctor of Philosophy and awarded by Brunel University.This thesis investigates the potential of wafer-scale integration (WSI) for the implementation of low-cost fine-grain parallel processing computer systems. As WSI is a relatively new subject, there was little work on which to base investigations. Indeed, most WSI architectures existed only as untried and sometimes vague proposals. Accordingly, the research strategy approached this problem by identifying a representative WSI structure and architecture on which to base investigations. An analysis of architectural proposals identified associative memory to be general purpose parallel processing component used in a wide range of WSI architectures. Furthermore, this analysis provided a set of WSI-level design requirements to evaluate the sustainability of different architectures as research vehicles. The WSI-ASP (WASP) device, which has a large associative memory as its main component is shown to meet these requirements and hence was chosen as the research vehicle. Consequently, this thesis addresses WSI potential through an in-depth investigation into the feasibility of implementing a large associative memory for the WASP device that meets the demanding technological constraints of WSI. Overall, the thesis concludes that WSI offers significant potential for the implementation of low-cost fine-grain parallel processing computer systems. However, due to the dual constraints of thermal management and the area required for the power distribution network, power density is a major design constraint in WSI. Indeed, it is shown that WSI power densities need to be an order of magnitude lower than VLSI power densities. The thesis demonstrates that for associative memories at least, VLSI designs are unsuited to implementation in WSI. Rather, it is shown that WSI circuits must be closely matched to the operational environment to assure suitable power densities. These circuits are significantly larger than their VLSI equivalents. Nonetheless, the thesis demonstrates that by concentrating on the most power intensive circuits, it is possible to achieve acceptable power densities with only a modest increase in area overheads.SER

D2.1 - Report on Selected TRNG and PUF Principles

This report represents the final version of Deliverable 2.1 of the HECTOR work package WP2. It is a result of discussions and work on Task 2.1 of all HECTOR partners involved in WP2. The aim of the Deliverable 2.1 is to select principles of random number generators (RNGs) and physical unclonable functions (PUFs) that fulfill strict technology, design and security criteria. For example, the selected RNGs must be suitable for implementation in logic devices according to the German AIS20/31 standard. Correspondingly, the selected PUFs must be suitable for applying similar security approach. A standard PUF evaluation approach does not exist, yet, but it should be proposed in the framework of the project. Selected RNGs and PUFs should be then thoroughly evaluated from the point of view of security and the most suitable principles should be implemented in logic devices, such as Field Programmable Logic Arrays (FPGAs) and Application Specific Integrated Circuits (ASICs) during the next phases of the project

Design and Validation of Network-on-Chip Architectures for the Next Generation of Multi-synchronous, Reliable, and Reconfigurable Embedded Systems

NETWORK-ON-CHIP (NoC) design is today at a crossroad. On one hand, the design principles to efficiently implement interconnection networks in the resource-constrained on-chip setting have stabilized. On the other hand, the requirements on embedded system design are far from stabilizing. Embedded systems are composed by assembling together heterogeneous components featuring differentiated operating speeds and ad-hoc counter measures must be adopted to bridge frequency domains. Moreover, an unmistakable trend toward enhanced reconfigurability is clearly underway due to the increasing complexity of applications. At the same time, the technology effect is manyfold since it provides unprecedented levels of system integration but it also brings new severe constraints to the forefront: power budget restrictions, overheating concerns, circuit delay and power variability, permanent fault, increased probability of transient faults. Supporting different degrees of reconfigurability and flexibility in the parallel hardware platform cannot be however achieved with the incremental evolution of current design techniques, but requires a disruptive approach and a major increase in complexity. In addition, new reliability challenges cannot be solved by using traditional fault tolerance techniques alone but the reliability approach must be also part of the overall reconfiguration methodology. In this thesis we take on the challenge of engineering a NoC architectures for the next generation systems and we provide design methods able to overcome the conventional way of implementing multi-synchronous, reliable and reconfigurable NoC. Our analysis is not only limited to research novel approaches to the specific challenges of the NoC architecture but we also co-design the solutions in a single integrated framework. Interdependencies between different NoC features are detected ahead of time and we finally avoid the engineering of highly optimized solutions to specific problems that however coexist inefficiently together in the final NoC architecture. To conclude, a silicon implementation by means of a testchip tape-out and a prototype on a FPGA board validate the feasibility and effectivenes

From Pre-Quantum to Post-Quantum IoT Security: A Survey on Quantum-Resistant Cryptosystems for the Internet of Things

© 2020 IEEE. This version of the article has been accepted for publication, after peer review. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes, creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works.[Absctract]: Although quantum computing is still in its nascent age, its evolution threatens the most popular public-key encryption systems. Such systems are essential for today's Internet security due to their ability for solving the key distribution problem and for providing high security in insecure communications channels that allow for accessing websites or for exchanging e-mails, financial transactions, digitally signed documents, military communications or medical data. Cryptosystems like Rivest-Shamir-Adleman (RSA), elliptic curve cryptography (ECC) or Diffie-Hellman have spread worldwide and are part of diverse key Internet standards like Transport Layer Security (TLS), which are used both by traditional computers and Internet of Things (IoT) devices. It is especially difficult to provide high security to IoT devices, mainly because many of them rely on batteries and are resource constrained in terms of computational power and memory, which implies that specific energy-efficient and lightweight algorithms need to be designed and implemented for them. These restrictions become relevant challenges when implementing cryptosystems that involve intensive mathematical operations and demand substantial computational resources, which are often required in applications where data privacy has to be preserved for the long term, like IoT applications for defense, mission-critical scenarios or smart healthcare. Quantum computing threatens such a long-term IoT device security and researchers are currently developing solutions to mitigate such a threat. This article provides a survey on what can be called post-quantum IoT systems (IoT systems protected from the currently known quantum computing attacks): the main post-quantum cryptosystems and initiatives are reviewed, the most relevant IoT architectures and challenges are analyzed, and the expected future trends are indicated. Thus, this article is aimed at providing a wide view of post-quantum IoT security and give useful guidelines...This work was supported in part by the Xunta de Galicia under Grant ED431G2019/01, in part by the Agencia Estatal de Investigación of Spain under Grant TEC2016-75067-C4- 1-R and Grant RED2018-102668-T, and in part by ERDF funds of the EU (AEI/FEDER, UE).Xunta de Galicia; ED431G2019/0

Digital Design of New Chaotic Ciphers for Ethernet Traffic

Durante los últimos años, ha habido un gran desarrollo en el campo de la criptografía, y muchos algoritmos de encriptado así como otras funciones criptográficas han sido propuestos.Sin embargo, a pesar de este desarrollo, hoy en día todavía existe un gran interés en crear nuevas primitivas criptográficas o mejorar las ya existentes. Algunas de las razones son las siguientes:• Primero, debido el desarrollo de las tecnologías de la comunicación, la cantidad de información que se transmite está constantemente incrementándose. En este contexto, existen numerosas aplicaciones que requieren encriptar una gran cantidad de datos en tiempo real o en un intervalo de tiempo muy reducido. Un ejemplo de ello puede ser el encriptado de videos de alta resolución en tiempo real. Desafortunadamente, la mayoría de los algoritmos de encriptado usados hoy en día no son capaces de encriptar una gran cantidad de datos a alta velocidad mientras mantienen altos estándares de seguridad.• Debido al gran aumento de la potencia de cálculo de los ordenadores, muchos algoritmos que tradicionalmente se consideraban seguros, actualmente pueden ser atacados por métodos de “fuerza bruta” en una cantidad de tiempo razonable. Por ejemplo, cuando el algoritmo de encriptado DES (Data Encryption Standard) fue lanzado por primera vez, el tamaño de la clave era sólo de 56 bits mientras que, hoy en día, el NIST (National Institute of Standards and Technology) recomienda que los algoritmos de encriptado simétricos tengan una clave de, al menos, 112 bits. Por otro lado, actualmente se está investigando y logrando avances significativos en el campo de la computación cuántica y se espera que, en el futuro, se desarrollen ordenadores cuánticos a gran escala. De ser así, se ha demostrado que algunos algoritmos que se usan actualmente como el RSA (Rivest Shamir Adleman) podrían ser atacados con éxito.• Junto al desarrollo en el campo de la criptografía, también ha habido un gran desarrollo en el campo del criptoanálisis. Por tanto, se están encontrando nuevas vulnerabilidades y proponiendo nuevos ataques constantemente. Por consiguiente, es necesario buscar nuevos algoritmos que sean robustos frente a todos los ataques conocidos para sustituir a los algoritmos en los que se han encontrado vulnerabilidades. En este aspecto, cabe destacar que algunos algoritmos como el RSA y ElGamal están basados en la suposición de que algunos problemas como la factorización del producto de dos números primos o el cálculo de logaritmos discretos son difíciles de resolver. Sin embargo, no se ha descartado que, en el futuro, se puedan desarrollar algoritmos que resuelvan estos problemas de manera rápida (en tiempo polinomial).• Idealmente, las claves usadas para encriptar los datos deberían ser generadas de manera aleatoria para ser completamente impredecibles. Dado que las secuencias generadas por generadores pseudoaleatorios, PRNGs (Pseudo Random Number Generators) son predecibles, son potencialmente vulnerables al criptoanálisis. Por tanto, las claves suelen ser generadas usando generadores de números aleatorios verdaderos, TRNGs (True Random Number Generators). Desafortunadamente, los TRNGs normalmente generan los bits a menor velocidad que los PRNGs y, además, las secuencias generadas suelen tener peores propiedades estadísticas, lo que hace necesario que pasen por una etapa de post-procesado. El usar un TRNG de baja calidad para generar claves, puede comprometer la seguridad de todo el sistema de encriptado, como ya ha ocurrido en algunas ocasiones. Por tanto, el diseño de nuevos TRNGs con buenas propiedades estadísticas es un tema de gran interés.En resumen, es claro que existen numerosas líneas de investigación en el ámbito de la criptografía de gran importancia. Dado que el campo de la criptografía es muy amplio, esta tesis se ha centra en tres líneas de investigación: el diseño de nuevos TRNGs, el diseño de nuevos cifradores de flujo caóticos rápidos y seguros y, finalmente, la implementación de nuevos criptosistemas para comunicaciones ópticas Gigabit Ethernet a velocidades de 1 Gbps y 10 Gbps. Dichos criptosistemas han estado basados en los algoritmos caóticos propuestos, pero se han adaptado para poder realizar el encriptado en la capa física, manteniendo el formato de la codificación. De esta forma, se ha logrado que estos sistemas sean capaces no sólo de encriptar los datos sino que, además, un atacante no pueda saber si se está produciendo una comunicación o no. Los principales aspectos cubiertos en esta tesis son los siguientes:• Estudio del estado del arte, incluyendo los algoritmos de encriptado que se usan actualmente. En esta parte se analizan los principales problemas que presentan los algoritmos de encriptado standard actuales y qué soluciones han sido propuestas. Este estudio es necesario para poder diseñar nuevos algoritmos que resuelvan estos problemas.• Propuesta de nuevos TRNGs adecuados para la generación de claves. Se exploran dos diferentes posibilidades: el uso del ruido generado por un acelerómetro MEMS (Microelectromechanical Systems) y el ruido generado por DNOs (Digital Nonlinear Oscillators). Ambos casos se analizan en detalle realizando varios análisis estadísticos a secuencias obtenidas a distintas frecuencias de muestreo. También se propone y se implementa un algoritmo de post-procesado simple para mejorar la aleatoriedad de las secuencias generadas. Finalmente, se discute la posibilidad de usar estos TRNGs como generadores de claves. • Se proponen nuevos algoritmos de encriptado que son rápidos, seguros y que pueden implementarse usando una cantidad reducida de recursos. De entre todas las posibilidades, esta tesis se centra en los sistemas caóticos ya que, gracias a sus propiedades intrínsecas como la ergodicidad o su comportamiento similar al comportamiento aleatorio, pueden ser una buena alternativa a los sistemas de encriptado clásicos. Para superar los problemas que surgen cuando estos sistemas son digitalizados, se proponen y estudian diversas estrategias: usar un sistema de multi-encriptado, cambiar los parámetros de control de los sistemas caóticos y perturbar las órbitas caóticas.• Se implementan los algoritmos propuestos. Para ello, se usa una FPGA Virtex 7. Las distintas implementaciones son analizadas y comparadas, teniendo en cuenta diversos aspectos tales como el consumo de potencia, uso de área, velocidad de encriptado y nivel de seguridad obtenido. Uno de estos diseños, se elige para ser implementado en un ASIC (Application Specific Integrate Circuit) usando una tecnología de 0,18 um. En cualquier caso, las soluciones propuestas pueden ser también implementadas en otras plataformas y otras tecnologías.• Finalmente, los algoritmos propuestos se adaptan y aplican a comunicaciones ópticas Gigabit Ethernet. En particular, se implementan criptosistemas que realizan el encriptado al nivel de la capa física para velocidades de 1 Gbps y 10 Gbps. Para realizar el encriptado en la capa física, los algoritmos propuestos en las secciones anteriores se adaptan para que preserven el formato de la codificación, 8b/10b en el caso de 1 Gb Ethernet y 64b/10b en el caso de 10 Gb Ethernet. En ambos casos, los criptosistemas se implementan en una FPGA Virtex 7 y se diseña un set experimental, que incluye dos módulos SFP (Small Form-factor Pluggable) capaces de transmitir a una velocidad de hasta 10.3125 Gbps sobre una fibra multimodo de 850 nm. Con este set experimental, se comprueba que los sistemas de encriptado funcionan correctamente y de manera síncrona. Además, se comprueba que el encriptado es bueno (pasa todos los test de seguridad) y que el patrón del tráfico de datos está oculto.<br /