Iterative amplitude/phase multiple-symbol differential sphere detection for DAPSK modulated transmissions

Differentially encoded and non-coherently detected transceivers exhibit a low complexity, since they dispense with complex channel estimation. Albeit this is achieved at the cost of requiring an increased transmit power, they are particularly beneficial, for example in cooperative communication scenarios, where the employment of channel estimation for all the mobile-to-mobile links may become unrealistic. In pursuit of high bandwidth efficiency, differential amplitude and phase shift keying (DAPSK) was devised using constellations of multiple concentric rings. In order to increase resilience against the typical high-Doppler-induced performance degradation of DAPSK and/or enhance the maximum achievable error-free transmission rate for DAPSK modulated systems, multiple-symbol differential detection (MSDD) may be invoked. However, the complexity of the maximum-a-posteriori (MAP) MSDD increases exponentially with the detection window size and hence may become excessive upon increasing the window size, especially in the context of iterative detection aided channel coded system. In order to circumvent this excessive complexity, we conceive a decomposed two-stage iterative amplitude and phase (A/P) detection framework, where the challenge of having a non-constant-modulus constellation is tackled with the aid of a specifically designed information exchange between the independent A/P detection stages, thus allowing the incorporation of reduced-complexity sphere detection (SD). Consequently, a near-MAP-MSDD performance can be achieved at a significantly reduced complexity, which may be five orders of magnitude lower than that imposed by the traditional MAP-MSDD in the 16-DAPSK scenario considered

DESIGN OF EMBEDDED FILTERS FOR INNER-LOOP POWER CONTROL IN WIRELESS CDMA COMMUNICATION SYSTEMS

ABSTRACT We study inner-loop power control for mobile wireless communication systems using code division multiple access transmission. We focus on the uplink, i.e., on communication from the mobile-to the base-station, and show how to minimise the variance of the signal-to-interference ratio (SIR) tracking error through incorporation of recursive filters. These filters complement existing power controllers and are designed by using a linear model which takes into account quantisation of the power control signal, dynamics of channel gains, interference from other users, target SIR, and SIR estimation errors. Simulation results indicate that significant performance gains can be obtained, even in situations where the models used for design are only an approximation

OFDM Waveform Optimisation for Joint Communications and Sensing

Radar systems are radios to sense objects in their surrounding environment. These operate at a defined set of frequency ranges. Communication systems are used to transfer information between two points. In the present day, proliferation of mobile devices and the advancement of technology have led to communication systems being ubiquitous. This has made these systems to operate at the frequency bands already used by the radar systems. Thus, the communication signal interferes a radar receiver and vice versa, degrading performance of both systems. Different methods have been proposed to combat this phenomenon. One of the novel topics in this is the RF convergence, where a given bandwidth is used jointly by both systems. A differentiation criterion must be adopted between the two systems so that a receiver is able to separately extract radar and communication signals. The hardware convergence due to the emergence of software-defined radios also motivated a single system be used for both radar and communication. A joint waveform is adopted for both radar and communication systems, as the transmit signal. As orthogonal frequency-division multiplexing (OFDM) waveform is the most prominent in mobile communications, it is selected as the joint waveform. Considering practical cellular communication systems adopting OFDM, there often exist unused subcarriers within OFDM symbols. These can be filled up with arbitrary data to improve the performance of the radar system. This is the approach used, where the filling up is performed through an optimisation algorithm. The filled subcarriers are termed as radar subcarriers while the rest as communication subcarriers, throughout the thesis. The optimisation problem minimises the Cramer--Rao lower bounds of the delay and Doppler estimates made by the radar system subject to a set of constraints. It also outputs the indices of the radar and communication subcarriers within an OFDM symbol, which minimise the lower bounds. The first constraint allocates power between radar and communication subcarriers depending on their subcarrier ratio in an OFDM symbol. The second constraint ensures the peak-to-average power ratio (PAPR) of the joint waveform has an acceptable level of PAPR. The results show that the optimised waveform provides significant improvement in the Cramer--Rao lower bounds compared with the unoptimised waveform. In compensation for this, the power allocated to the communication subcarriers needs to be reduced. Thus, improving the performances of the radar and communication systems are a trade-off. It is also observed that for the minimum lower bounds, radar subcarriers need to be placed at the two edges of an OFDM symbol. Optimisation is also seen to improve the estimation performance of a maximum likelihood estimator, concluding that optimising the subcarriers to minimise a theoretical bound enables to achieve improvement for practical systems

Improved timing recovery in wireless mobile receivers

The problem of timing recovery in wireless mobile receiver systems is critical. This is partly because timing recovery functions must follow rapid parameter changes inherent in mobile systems and partly because both bandwidth and power must be conserved in low signal to noise ratio communication channels. The ultimate goal is therefore to achieve a low bit error rate on the recovered information for improving QoS provisioning to terminal mobile users. Traditional timing recovery methods have over-relied on phase-locked loops for timing information adjustment. However, associated schemes do not exploit code properties. This leads to synchronization difficulties in digital receivers separated from transmitters by lossy channels. In this paper we present a soft timing phase estimation algorithm for wireless mobile receivers in low signal to noise ratios. In order to develop a bandwidth and power efficient timing recovery method for wireless mobile receivers, a raised cosine filter and a multilevel phase shift keying modulation scheme are implemented and no clock signals are transmitted to the receiver. In the proposed method, the receiver exploits the soft decisions computed at each turbo decoding iteration to provide reliable estimates of a soft timing signal, which in turn, improves the decoding time. The derived method, based on sequential minimization techniques, approaches the theoretical Cramer-Rao bound with unbiased estimates within a few iterations.Key Words: discrete polyphase matched filters, maximum likelihood estimators, iterative turbo receivers, log-MAP b

On the influence of the channel impulsional response estimation on the performance of a linear interference canceller for a DS/CDMA system

In a code division multiple access (CDMA) mobile radio communication system, interference from other users is one of the most critical drawbacks due to the lack of perfect orthogonality between user access codes. So far, practical systems have used power control to overcome fading and near/far effects. Another approach which also results in an important improvement of the capacity is the use of interference cancellers. A simple linear interference cancellation scheme for coherent BPSK modulation is proposed and analyzed under Rayleigh multipath fading, and in particular, the influence of the channel impulsive response estimation on the performance of the cancellation scheme has been assessed.Peer ReviewedPostprint (published version

Massive MIMO Multicasting in Noncooperative Cellular Networks

We study the massive multiple-input multiple-output (MIMO) multicast transmission in cellular networks where each base station (BS) is equipped with a large-scale antenna array and transmits a common message using a single beamformer to multiple mobile users. We first show that when each BS knows the perfect channel state information (CSI) of its own served users, the asymptotically optimal beamformer at each BS is a linear combination of the channel vectors of its multicast users. Moreover, the optimal combining coefficients are obtained in closed form. Then we consider the imperfect CSI scenario where the CSI is obtained through uplink channel estimation in timedivision duplex systems. We propose a new pilot scheme that estimates the composite channel which is a linear combination of the individual channels of multicast users in each cell. This scheme is able to completely eliminate pilot contamination. The pilot power control for optimizing the multicast beamformer at each BS is also derived. Numerical results show that the asymptotic performance of the proposed scheme is close to the ideal case with perfect CSI. Simulation also verifies the effectiveness of the proposed scheme with finite number of antennas at each BS.Comment: to appear in IEEE JSAC Special Issue on 5G Wireless Communication System

Stochastic Signal Processing and Power Control for Wireless Communication Systems

This dissertation is concerned with dynamical modeling, estimation and identification of wireless channels from received signal measurements. Optimal power control algorithms, mobile location and velocity estimation methods are developed based on the proposed models. The ultimate performance limits of any communication system are determined by the channel it operates in. In this dissertation, we propose new stochastic wireless channel models which capture both the space and time variations of wireless systems. The proposed channel models are based on stochastic differential equations (SDEs) driven by Brownian motions. These models are more realistic than the time invariant models encountered in the literature which do not capture and track the time varying characteristics of the propagation environment. The statistics of the proposed models are shown to be time varying, and converge in steady state to their static counterparts. Cellular and ad hoc wireless channel models are developed. In urban propagation environment, the parameters of the channel models can be determined from approximating the band-limited Doppler power spectral density (DPSD) by rational transfer functions. However, since the DPSD is not available on-line, a filterbased expectation maximization algorithm and Kalman filter to estimate the channel parameters and states, respectively, are proposed. The algorithm is recursive allowing the inphase and quadrature components and parameters to be estimated on-line from received signal measurements. The algorithms are tested using experimental data, and the results demonstrate the method’s viability for both cellular and ad hoc networks. Power control increases system capacity and quality of communications, and reduces battery power consumption. A stochastic power control algorithm is developed using the so-called predictable power control strategies. An iterative distributed algorithm is then deduced using stochastic approximations. The latter only requires each mobile to know its received signal to interference ratio at the receiver

Fast Power and Energy Efficiency Analysis of FPGA-based Wireless Base-band Processing

Nowadays, demands for high performance keep on increasing in the wireless communication domain. This leads to a consistent rise of the complexity and designing such systems has become a challenging task. In this context, energy efficiency is considered as a key topic, especially for embedded systems in which design space is often very constrained. In this paper, a fast and accurate power estimation approach for FPGA-based hardware systems is applied to a typical wireless communication system. It aims at providing power estimates of complete systems prior to their implementations. This is made possible by using a dedicated library of high-level models that are representative of hardware IPs. Based on high-level simulations, design space exploration is made a lot faster and easier. The definition of a scenario and the monitoring of IP's time-activities facilitate the comparison of several domain-specific systems. The proposed approach and its benefits are demonstrated through a typical use case in the wireless communication domain.Comment: Presented at HIP3ES, 201