Four-Way Microstrip-Based Power Combining for Microwave Outphasing Power Amplifiers

A lossless multi-way outphasing and power combining system for microwave power amplification is presented. The architecture addresses one of the primary drawbacks of Chireix outphasing; namely, the sub-optimal loading conditions for the branch power amplifiers. In the proposed system, four saturated power amplifiers interact through a lossless power combining network to produce nearly resistive load modulation over a 10:1 range of output powers. This work focuses on two microstrip-based power combiner implementations: a hybrid microstrip/discrete implementation using a combination of microstrip transmission line sections with discrete shunt elements, and an all-microstrip implementation incorporating open-circuited radial stubs. We demonstrate and compare these techniques in a 2.14 GHz power amplifier system. With the all-microstrip implementation, the system demonstrates a peak CW drain efficiency of 70% and drain efficiency of over 60% over a 6.5-dB outphasing output power range with a peak power of over 100 W. We demonstrate W-CDMA modulation with 55.6% average modulated efficiency at 14.1 W average output power for a 9.15-dB peak to average power ratio (PAPR) signal. The performance of this all-microstrip system is compared to that of the proposed hybrid microstrip/discrete version and a previously reported implementation in discrete lumped-element form.Massachusetts Institute of Technology. Center for Integrated Circuits and SystemsMassachusetts Institute of Technology. Microsystems Technology Laboratories. GaN Energy Initiativ

Multi-Band Outphasing Power Amplifier Design for Mobile and Base Stations

New generations of wireless communication systems require linear efficient RF power amplifiers (PAs) for higher transmission data rates and longer battery life. On the contrary, conventional PAs are normally designed for peak efficiency under maximum output power (Pout). Thus, in power back-off, the overall efficiency degrades significantly and the average efficiency is much lower than the efficiency at maximum Pout. Chireix outphasing PA, also called LINC (Linear amplification using Non-linear Components), is one of the most promising techniques to improve the efficiency at power back-off. In this method, a variable envelope input signal is first decomposed into two constant-envelope phase-modulated signals and then amplified using two highly efficient non-linear PAs. The output signals are combined preferably in a loss-less power combiner to build the desired output signal. In this way, the PA exhibits high efficiency with good linearity. In this thesis, first we analyze a complex model of outphasing combiner considering its nonidealities such as reflection and loss in transmission lines (TL). Then we propose a compact model with analytical formula that is validated through several comparative tests using ADS and Spectre RF. Furthermore, we analyze the effect of reactive load in Chireix combiner with stubs (a parallel inductor and capacitor), while distinguishing between its capacitive and inductive parts. It is demonstrated that only the capacitive part of the reactive load degrades the performances. Based on this, a new architecture (Z LINC) is proposed where the power combiner is designed to provide a zero capacitive load to the PAs whatever the outphasing angle. The theory describing the operations of the system is developed and a 900 MHz classical LINC and Z-LINC PAs are designed and measured. In addition, a miniaturization technique is proposed which employs λ/8 or smaller TLs instead of conventional λ/4 TLs in outphasing power combiner. This technique is applied to implement a 900 MHz PA using LDMOS power transistors. Besides single-band PAs, dual-band PAs are more and more needed because of an increasing demand for wireless communication terminals to handle multi-band operation. In chapter 5, a new compact design approach for dual-band transmitters based on a reconfigurable outphasing combiner is proposed. The objective is to avoid the cumbersome implementations where several PAs and matching network are used in parallel. The technique is applied to design a dual band PA with a fully integrated power combiner in 90 nm CMOS technology. An inverter-based class D PA topology, particularly suitable for outphasing and multimode operations is presented. The TLs in the combiner, realized using a network of on-chip series inductors and parallel capacitors, are reconfigurable from λ/4 in 1800 MHz to λ/8 in 900 MHz. In order to maximize the efficiency, the on-chip inductors are implemented using high quality factor on chip slab inductors. The measured maximum Pout at 900/1800 MHz are 24.3 and 22.7 dBm with maximum efficiencies of 51% and 34% respectively

Evaluación de algunos amplificadores apropiados para implementar sistemas de amplificación lineal a partir de componentes no-lineales (linc) : amplificador de potencia clase-e

Ingeniero (a) ElectrónicoPregrad

Linearity of Outphasing Radio Transmitters

The outphasing transmitter is a promising technique, which can simultaneously achieve high linearity and power efficiency, thereby addressing the major design requirements of next generation transmitters. It employs highly non-linear power amplifier (PA) classes in a linear manner, in principle transmitting a distortion-free signal. Due to symmetric nature of the outphasing architecture, its linearity performance is constrained by any mismatches and non-linear effects encountered in the RF paths. This thesis analyzes the linearity performance of outphasing transmitters (in terms of ACLR specification) for LTE base station applications, under the non-linear effects and tolerances present in practical implementations. The system-level model, built in Matlab software, investigates the important non-linear effects present in outphasing transmitters, including gain and phase imbalance, IQ modulator mismatches, delay imbalance, and the non-linear effects of PAs and Chireix combiners. The path and delay mismatches result in only partial cancellation of the wideband quadrature signal, and thus create interference in both the in-band and out-of-band frequency regions. The misalignment in IQ modulators, such as gain/phase imbalance and carrier leakage, introduces amplitude and phase modulation in the outphased signals. The quadrature modulator mismatches, in conjunction with amplifier nonlinearity, result in spectral regrowth around the carrier frequency. The transmitter linearity performance is also affected by mismatches in the non-linear characteristics of the PAs. Realistic square-wave signals, exhibiting finite rise- and fall- time, also create spectral leakage for distinct rise/fall times in each outphasing branch. Furthermore, the Chireix combiner severely degrades the linearity of outphasing transmitters; it produces ACLR well below the specified limit for LTE base stations. This makes mandatory the compensation of Chireix combiner induced non-linearity in outphasing transmitters. The strict linearity requirements (for LTE downlink applications) present a small tolerance window for mismatches experienced in practical circuits. The relatively small tolerance margin indicates the need of linearization and compensation techniques in outphasing transmitters

Passive and active components development for broadband applications

Recently, GaN HEMTs have been proven to have numerous physical properties, resulting in transistors with greatly increased power densities when compared to the other well-established FET technologies. This advancement spurred research and product development towards power-band applications that require both high power and high efficiency over the wide band. Even though the use of multiple narrow band PAs covering the whole band has invariably led to better performance in terms of efficiency and noise, there is an associated increase in cost and in the insertion loss of the switches used to toggle between the different operating bands. The goal, now, of the new technology is to replace the multiple narrow band PAs with one broadband PA that has a comparable efficiency performance. In our study here, we have investigated a variety of wide band power amplifiers, including class AB PAs and their implementation in distributed and feedback PAs.Additionally, our investigation has included switching-mode PAs as they are well-known for achieving a relatively high efficiency. Besides having a higher efficiency, they are also less susceptible to parameter variations and could impose a lower thermal stress on the transistors than the conventional-mode PAs. With GaN HEMTs, we have demonstrated: a higher than 37 dBm output power and a more than 30% drain efficiency over 0.02 to 3 GHz for the distributed power amplifier; a higher than 30 dBm output power with more than a 22% drain efficiency over 0.1 to 5 GHz for the feedback amplifier; and at least a 43 dBm output power with a higher than 63% drain efficiency over 0.05 to 0.55 GHz for the class D PA. In many communication applications, however, achieving both high efficiency and linearity in the PA design is required. Therefore, in our research, we have evaluated several linearization and efficiency enhancement techniques.We selected the LInear amplification with Nonlinear Components (LINC) approach. Highly efficient combiner and novel efficiency enhancement techniques like the power recycling combiner and adaptive bias LINC schemes have been successfully developed and verified to achieve a combined high efficiency with a relatively high linearity

Techniques for high-efficiency outphasing power amplifiers

Thesis (Ph. D.)--Massachusetts Institute of Technology, Dept. of Electrical Engineering and Computer Science, 2011.Cataloged from PDF version of thesis.Includes bibliographical references (p. 171-177).A trade-off between linearity and efficiency exists in conventional power amplifiers (PAs). The outphase amplifying concept overcomes this trade-off by enabling the use of high efficiency, non-linear power amplifiers for linear amplification. However, the efficiency improvement is limited by the efficiency of the output power combiner. This thesis investigates techniques to overcome this efficiency limit while maintaining sufficient linearity. Two techniques are proposed. The first technique is called the outphasing energy recovery amplifier (OPERA), which recovers the normally wasted power back to the power supply and utilizes a resistance compression network for improved linearity. A 48-MHz, 20-W prototype OPERA system was built which demonstrates more than 2x higher efficiency than the standard outphasing system for a 16-QAM signal. The second technique to improve the efficiency of the outphasing system is asymmetric multilevel outphasing (AMO) modulation. In the AMO system, the amplitude for each of the two outphased PAs can switch independently among multiple discrete levels, significantly reducing the energy lost in the power combiner. Three different AMO prototypes were built, each of which demonstrate between 2x-3x efficiency improvement compared to the standard outphasing system. A 2.4-GHz, 500- mW prototype made in a 65-nm CMOS process achieves an average system efficiency of 28.7% for a 20-MHz 64-QAM signal. To the author's best knowledge, this is the highest reported efficiency for a CMOS PA in the 2-2.7 GHz range for signal bandwidths greater than 10 MHz.by Philip Andrew Godoy.Ph.D

Lossless multi-way power combining and outphasing for radio frequency power amplifiers

Thesis (S.M.)--Massachusetts Institute of Technology, Dept. of Electrical Engineering and Computer Science, 2013.Cataloged from PDF version of thesis.Includes bibliographical references (p. 102-106).For applications requiring the use of power amplifiers (PAs) operating at high frequencies and power levels, it is often preferable to construct multiple low power PAs and combine their output powers to form a high-power PA. Moreover, such PAs must often be able to provide dynamic control of their output power over a wide range, and maintain high efficiency across their operating range. This research work describes a new power combining and outphasing system that provides both high efficiency and dynamic output power control. The introduced system combines power from four or more PAs, and overcomes the loss and reactive loading problems of previous outphasing systems. It provides ideally lossless power combining, along with nearly-resistive loading of the individual power amplifiers over a very wide output power range. The theoretical fundamentals underlying the behavior and operation of this new combining system are thoroughly developed. Additionally, a straight-forward combiner design methodology is provided. The prototype design of a 27.12 MHz, four-way power combining and outphasing system is presented, implemented, and its performance is experimentally validated over a 1OW-1OOW (10:1) output power range.by Alexander S. Jurkov.S.M