Emitter velocity estimation comparison for frequency difference of arrival measurement based single and multiple reference lateration algorithm

The accuracy at which the instantaneous velocity and position of a non-stationary emitting source estimated using a lateration algorithm depends on several factors such as the lateration algorithm approach, the number and choice of reference receiving station (RS) used in developing the lateration algorithm. In this paper, the use of multiple reference RSs was proposed to improve the velocity estimation accuracy of the frequency difference of arrival (FDOA) based lateration algorithm. The velocity estimation performance of the proposed multiple reference FDOA based lateration algorithm is compared with the conventional approach of using single reference RS at some selected emitter positions using Monte Carlo simulation. Simulation result based on an equilateral triangle RS configuration shows that the use of multiple reference RSs improved the velocity estimation accuracy of the lateration algorithm. Based on the selected emitter positions, a reduction in velocity estimation error of about 0.033m/s and 1.31 m/s for emitter positions at ranges 0.5 km and 5 km respectively was achieved using the multiple reference lateration algorithm

A Moving Source Localization Method for Distributed Passive Sensor Using TDOA and FDOA Measurements

The conventional moving source localization methods are based on centralized sensors. This paper presents a moving source localization method for distributed passive sensors using TDOA and FDOA measurements. The novel method firstly uses the steepest descent algorithm to obtain a proper initial value of source position and velocity. Then, the coarse location estimation is obtained by maximum likelihood estimation (MLE). Finally, more accurate location estimation is achieved by subtracting theoretical bias, which is approximated by the actual bias using the estimated source location and noisy data measurement. Both theoretical analysis and simulations show that the theoretical bias always meets the actual bias when the noise level is small, and the proposed method can reduce the bias effectively while keeping the same root mean square error (RMSE) with the original MLE and Taylor-series method. Meanwhile, it is less sensitive to the initial guess and attains the CRLB under Gaussian TDOA and FDOA noise at a moderate noise level before the thresholding effect occurs

Locating sensors with fuzzy logic algorithms

In a system formed by hundreds of sensors deployed in a huge area it is important to know the position where every sensor is. This information can be obtained using several methods. However, if the number of sensors is high and the deployment is based on ad-hoc manner, some auto-locating techniques must be implemented. In this paper we describe a novel algorithm based on fuzzy logic with the objective of estimating the location of sensors according to the knowledge of the position of some reference nodes. This algorithm, called LIS (Localization based on Intelligent Sensors) is executed distributively along a wireless sensor network formed by hundreds of nodes, covering a huge area. The evaluation of LIS is led by simulation tests. The result obtained shows that LIS is a promising method that can easily solve the problem of knowing where the sensors are located.Junta de Andalucía P07-TIC-0247

Error Minimization in Indoor Wireless Sensor Network Localization Using Genetic Technique

Using the genetic technique, error minimisation in indoor wireless sensor network localisation improves indoor wireless sensor network localisation during this field research. Sensor localisation-based techniques; several wireless device network applications require awareness of each node's physical location. The discovery of the position complete utilising range measurements also as sensor localisation received signal strength in time of arrival and sensor localisation received signal strength in a time difference of arrival and angle of arrival. WSN in positioning algorithms like the angle of arrival between two neighbour nodes. A wireless sensor network using positioning techniques in the area is assumed as localisation. WSNs always operate in an unattended manner, various situations like dynamic situations in the wireless network. It's impossible to exchange sensor manner after deployment. Therefore, a fundamental objective is to optimise the sensor manner lifetime. There has been much specialising in mobile sensor networks, and we have even seen the event of small-profile sensing devices that are ready to control their movement. Although it's been shown that mobility alleviates several issues regarding sensor network coverage and connectivity, many challenges remain node localisation in wireless device network is extremely important for several applications and received signal strength indicator has the capability of sensing, actuating the environmental data the actual-time and favourable information are often collected using the sensor in WSN systems. WSN is often combined with the internet of things to permit the association and extensive access to sensor data, and genetic techniques search the position of the nodes in WSN using all anchor nodes. A proposed algorithm as a genetic technique supported received signal strength, angle of arrival, receptive wireless device and also localisation wireless network. In the study, this paper problem that accuracy is low and error more, but the proposed algorithm overcomes this problem and minimises the error rate. Finally, the simplest possible location satisfies each factor with a minimal error rate and absolute best solution using GA

Wireless sensor network’s localization based on multiple signal classification algorithm

Wireless sensor networks (WSNs) are a number of sensitive nodes senses a physical phenomenon at the position of their deployment then sends information to the base station to take appropriate operation. (WSNs) are used in many applications such track military targets, discover fires, study natural phenomena such as earthquakes, humidity, heat, etc. The nodes are spread in large areas and it is difficult to locate them manually because they are published randomly by planes or any other method and since the information received from sensitive nodes is useless without knowing their location in this case a problem resulted in the positioning of the nodes. So it unacceptable to equip each sensor node with global position system (GPS) due to various problems such as raises cost and energy consumption. In this paper explained a non-GPS technique to self-positioning of nodes in (WSNs) by using the multiple signal classification (MUSIC) algorithm to determine the position of the active sensor through estimated the direction of arrival (DOA) of the node signal. Then modified MUSIC algorithm (M-MUSIC) to solve the problem of coherent signal. MATLAB program successfully used to simulate the proposed algorithm

Exploiting Structural Signal Information in Passive Emitter Localization

The operational use of systems for passive geolocation of radio frequency emitters poses various challenges to single sensor systems or sensor networks depending on the measurement methods. Position estimation by means of direction finding systems often requires complex receiver and antenna technique. Time (Difference) of Arrival methods (TDOA, TOA) are based on measurements regarding the signal propagation duration and generally require broadband communication links to transmit raw signal data between spatially separated receivers of a sensor network. Such bandwidth requirements are particularly challenging for applications with moving sensor nodes. This issue is addressed in this thesis and techniques that use signal structure information of the considered signals are presented which allow a drastic reduction of the communication requirements. The advantages of using knowledge of the signal structure for TDOA based emitter localization are shown using two exemplary applications. The first case example deals with the passive surveillance of the civil airspace (Air Traffic Management, ATM) using a stationary sensor network. State of the art airspace surveillance is mainly based on active radar systems (Primary Surveillance Radar, PSR), cooperative secondary radar systems (Secondary Surveillance Radar, SSR) and automatic position reports from the aircraft itself (Automatic Dependent Surveillance-Broadcast, ADS-B). SSR as well as ADS-B relies on aircrafts sending transponder signals at a center frequency of 1090 MHz. The reliability and accuracy of the position reports sent by aircrafts using ADS-B are limited and not sufficient to ensure safe airspace separation for example of two aircrafts landing on parallel runways. In the worst case, the data may even be altered with malicious intent. Using passive emitter localization and tracking based on multilateration (TDOA/hyperbolic localization), a precise situational awareness can be given which is independent of the content of the emitted transponder signals. The high concentration of sending targets and the high number of signals require special signal processing and information fusion techniques to overcome the huge amount of data. It will be shown that a multilateration network that employs those techniques can be used to improve airspace security at reasonable costs. For the second case, a concept is introduced which allows TDOA based emitter localization with only one moving observer platform. Conventional TDOA measurements are obtained using spatially distributed sensor nodes which capture an emitted signal at the same time. From those signals, the time difference of arrival is estimated. Under certain conditions, the exploitation of signal structure information allows to transfer the otherwise only spatial into a spatial and temporal measurement problem. This way, it is possible to obtain TDOA estimates over multiple measurement time steps using a single moving observer and to thus localize the emitter of the signals. The concept of direct position determination is applied to the single sensor signal structure TDOA scheme and techniques for direct single sensor TDOA are introduced. The validity and performance of the presented methods is shown in theoretical analysis in terms of Cramér-Rao Lower Bounds, Monte-Carlo simulations and by evaluation of real data gained during field experiments

Interference Mitigation and Localization Based on Time-Frequency Analysis for Navigation Satellite Systems

Interference Mitigation and Localization Based on Time-Frequency Analysis for Navigation Satellite SystemsNowadays, the operation of global navigation satellite systems (GNSS) is imperative across a multitude of applications worldwide. The increasing reliance on accurate positioning and timing information has made more serious than ever the consequences of possible service outages in the satellite navigation systems. Among others, interference is regarded as the primary threat to their operation. Due the recent proliferation of portable interferers, notably jammers, it has now become common for GNSS receivers to endure simultaneous attacks from multiple sources of interference, which are likely spatially distributed and transmit different modulations. To the best knowledge of the author, the present dissertation is the first publication to investigate the use of the S-transform (ST) to devise countermeasures to interference. The original contributions in this context are mainly: • the formulation of a complexity-scalable ST implementable in real time as a bank of filters; • a method for characterizing and localizing multiple in-car jammers through interference snapshots that are collected by separate receivers and analysed with a clever use of the ST; • a preliminary assessment of novel methods for mitigating generic interference at the receiver end by means the ST and more computationally efficient variants of the transform. Besides GNSSs, the countermeasures to interference proposed are equivalently applicable to protect any direct-sequence spread spectrum (DS-SS) communication

Efficient closed-form estimators in multistatic target localization and motion analysis

Object localization is fast becoming an important research topic because of its wide applications. Often of the time, object localization is accomplished in two steps. The first step exploits the characteristics of the received signals and extracts certain localization information i.e. measurements. Some typical measurements include timeof-arrival (TOA), time-difference-of-arrival (TDOA), received signal strength (RSS) and angle-of-arrival (AOA). Together with the known receiver position information, the object location is then estimated in the second step from the obtained measurements. The localization of an object using a number of sensors is often challenged due to the highly nonlinear relationship between the measurements and the object location. This thesis focuses on the second step and considers designing novel and efficient localization algorithms to solve such a problem. This thesis first derives a new algebraic positioning solution using a minimum number of measurements, and from which to develop an object location estimator. Two measurements are sufficient in 2-D and three in 3-D to yield a solution if they are consistent. The derived minimum measurement solution is exact and reduces the computation to the roots of a quadratic equation. The solution derivation also leads to simple criteria to ascertain if the line of positions from two measurements intersects. By partitioning the overdetermined set of measurements first to obtain the individual minimum measurement solutions, we propose a best linear unbiased estimator to form the final location estimate. The analysis supports the proposed estimator in reaching the Cramer-Rao Lower Bound (CRLB) accuracy under Gaussian noise. A measurement partitioning scheme is developed to improve performance when the noise level becomes large. We mainly use elliptic time delay measurements for presentation, and the derived results apply to the hyperbolic time difference measurements as well. Both the 2-D and 3-D scenarios are considered. A multistatic system uses a transmitter to illuminate the object of interest and collects the reflected signal by several receivers to determine its location. In some scenarios such as passive coherent localization or for gaining flexibility, the position of the transmitter is not known. In this thesis, we investigate the use of the indirect path measurements reflected off the object alone, or together with the direct path measurements from the transmitter to receiver for locating the object in the absence of the transmitter position. We show that joint estimation of the object and transmitter positions from both the indirect and direct measurements can yield better object location estimate than using the indirect measurements only by eliminating the dependency of the transmitter position. An algebraic closed-form solution is developed for the nonlinear problem of joint estimation and is shown analytically to achieve the CRLB performance under Gaussian noise over the small error region. To complete the study and gain insight, the optimum receiver placement in the absence of transmitter position is derived, by minimizing the estimation confidence region or the estimation variance for the object location. The performance lost due to unknown transmitter position under the optimum geometries is quantified. Simulations confirm well with the theoretical developments. In practice, a more realistic localization scenario with the unknown transmitter is that the transmitter works non-cooperatively. In this situation, no timestamp is available in the transmitted signal so that the signal sent time is often not known. This thesis next considers the extension of the localization scenario to such a case. More generally, the motion potential of the unknown object and transmitter is considered in the analysis. When the transmitted signal has a well-defined pattern such as some standard synchronization or pilot sequence, it would still be able to estimate the indirect and direct time delays and Doppler frequency shifts but with unknown constant time delay and frequency offset added. In this thesis, we would like to estimate the object and transmitter positions and velocities, and the time and frequency offsets jointly. Both dynamic and partial dynamic localization scenarios based on the motion status of the object and the transmitter are considered in this thesis. By investigating the CRLB of the object location estimate, the improvement in position and velocity estimate accuracy through joint estimation comparing with the differencing approach using TDOA/FDOA measurements is evaluated. The degradation due to time and frequency offsets is also analyzed. Algebraic closed-form solutions to solve the highly nonlinear joint estimation problems are then proposed in this thesis, followed by the analysis showing that the CRLB performance can be achieved under Gaussian noise over the small error region. When the transmitted signal is not time-stamped and does not have a well-defined pattern such as some standard synchronization or pilot sequence, it is often impossible to obtain the indirect and direct measurements separately. Instead, a self-calculated TDOA between the indirect- and direct-path TOAs shall be considered which does not require any synchronization between the transmitter and a receiver, or among the receivers. A refinement method is developed to locate the object in the presence of the unknown transmitter position, where a hypothesized solution is needed for initialization. Analysis shows that the refinement method is able to achieve the CRLB performance under Gaussian noise. Three realizations of the hypothesized solution applying multistage processing to simplify the nonlinear estimation problem are derived. Simulations validate the effectiveness in initializing the refinement estimator

Cooperatively Extending the Range of Indoor Localisation

̶Whilst access to location based information has been mostly possible in the\ud outdoor arena through the use of GPS, the provision of accurate positioning estimations and\ud broad coverage in the indoor environment has proven somewhat problematic to deliver.\ud Considering more time is spent in the indoor environment, the requirement for a solution is\ud obvious. The topography of an indoor location with its many walls, doors, pillars, ceilings\ud and floors etc. muffling the signals to \from mobile devices and their tracking devices, is one\ud of the many barriers to implementation. Moreover the cha racteristically noisy behaviour of\ud wireless devices such as Bluetooth headsets, cordless phones and microwaves can cause\ud interference as they all operate in the same band as Wi -Fi devices. The limited range of\ud tracking devices such as Wireless Access Point s (AP), and the restrictions surrounding their\ud positioning within a buildings’ infrastructure further exacerbate this issue, these difficulties\ud provide a fertile research area at present.\ud The genesis for this research is the inability of an indoor location based system (LBS) to\ud locate devices beyond the range of the fixed tracking devices. The hypothesis advocates a\ud solution that extends the range of Indoor LBS using Mobile Devices at the extremities of\ud Cells that have a priori knowledge of their location, and utilizing these devices to ascertain\ud the location of devices beyond the range of the fixed tracking device. This results in a\ud cooperative localisation technique where participating devices come together to aid in the\ud determination of location of device s which otherwise would be out of scope