Parameter and Payload Identification of a 2-DOF Robotic Manipulator: An Algebraic Identification Approach

Este artículo aborda el problema de identificar los parámetros y las cargas útiles de un manipulador robótico 2-DOF. La metodología propuesta para nuestra investigación fue el método de identificación algebraica realizada en dos etapas: primero, identificando los parámetros del manipulador, y segundo, identificando la carga útil de la punta. Se utilizaron dos casos de simulación numérica diferentes para validar la metodología de identificación propuesta. En ambos casos se logró una rápida convergencia con un bajo porcentaje de error.This paper addresses the problem of identifying the parameters and the payloads of a 2-DOF robotic manipulator. The methodology proposed for our research was the algebraic identification method conducted in two stages: First, identifying the parameters of the manipulator and second, identifying the tip payload. Two different numerical simulation cases were used to validate the proposed identification methodology. In both cases, fast convergence was achieved with a low error percentage

Dynamic modeling, property investigation, and adaptive controller design of serial robotic manipulators modeled with structural compliance

Research results on general serial robotic manipulators modeled with structural compliances are presented. Two compliant manipulator modeling approaches, distributed and lumped parameter models, are used in this study. System dynamic equations for both compliant models are derived by using the first and second order influence coefficients. Also, the properties of compliant manipulator system dynamics are investigated. One of the properties, which is defined as inaccessibility of vibratory modes, is shown to display a distinct character associated with compliant manipulators. This property indicates the impact of robot geometry on the control of structural oscillations. Example studies are provided to illustrate the physical interpretation of inaccessibility of vibratory modes. Two types of controllers are designed for compliant manipulators modeled by either lumped or distributed parameter techniques. In order to maintain the generality of the results, neither linearization is introduced. Example simulations are given to demonstrate the controller performance. The second type controller is also built for general serial robot arms and is adaptive in nature which can estimate uncertain payload parameters on-line and simultaneously maintain trajectory tracking properties. The relation between manipulator motion tracking capability and convergence of parameter estimation properties is discussed through example case studies. The effect of control input update delays on adaptive controller performance is also studied

Human-Multirobot Collaborative Mobile Manipulation: the Omnid Mocobots

The Omnid human-collaborative mobile manipulators are an experimental platform for testing control architectures for autonomous and human-collaborative multirobot mobile manipulation. An Omnid consists of a mecanum-wheel omnidirectional mobile base and a series-elastic Delta-type parallel manipulator, and it is a specific implementation of a broader class of mobile collaborative robots ("mocobots") suitable for safe human co-manipulation of delicate, flexible, and articulated payloads. Key features of mocobots include passive compliance, for the safety of the human and the payload, and high-fidelity end-effector force control independent of the potentially imprecise motions of the mobile base. We describe general considerations for the design of teams of mocobots; the design of the Omnids in light of these considerations; manipulator and mobile base controllers to achieve useful multirobot collaborative behaviors; and initial experiments in human-multirobot collaborative mobile manipulation of large, unwieldy payloads. For these experiments, the only communication among the humans and Omnids is mechanical, through the payload.Comment: 8 pages, 10 figures. Videos available at https://www.youtube.com/watch?v=SEuFfONryL0. Submitted to IEEE Robotics and Automation Letters (RA-L

A review of aerial manipulation of small-scale rotorcraft unmanned robotic systems

Small-scale rotorcraft unmanned robotic systems (SRURSs) are a kind of unmanned rotorcraft with manipulating devices. This review aims to provide an overview on aerial manipulation of SRURSs nowadays and promote relative research in the future. In the past decade, aerial manipulation of SRURSs has attracted the interest of researchers globally. This paper provides a literature review of the last 10 years (2008–2017) on SRURSs, and details achievements and challenges. Firstly, the definition, current state, development, classification, and challenges of SRURSs are introduced. Then, related papers are organized into two topical categories: mechanical structure design, and modeling and control. Following this, research groups involved in SRURS research and their major achievements are summarized and classified in the form of tables. The research groups are introduced in detail from seven parts. Finally, trends and challenges are compiled and presented to serve as a resource for researchers interested in aerial manipulation of SRURSs. The problem, trends, and challenges are described from three aspects. Conclusions of the paper are presented, and the future of SRURSs is discussed to enable further research interests

Multi-robot cooperation

Abstract. This bachelor’s thesis familiarizes with multi-robot cooperation. The main interest is in two robot manipulators. This thesis is a literature review. The operation of the robot and the phenomena that act on them while in operation are investigated from kinematics and command architecture point of view. This thesis is based on manuals from two KUKA robots from University of Oulu, so in the future the use and understanding of their cooperation would be easier. The results gave good understanding of robot software calculations for trajectories and geometrics and what other has to consider when controlling a multi-robot system. This is a good base for deeper theoretical research for robot system software and practical testing.Usean robotin yhteiskäyttö. Tiivistelmä. Tässä opinnäytetyössä perehdytään usean robotin yhteiskäyttöön, jossa mielenkiinnon kohteena on kahden robottikäden yhteistoiminta. Työ on kirjallisuuskatsaus. Robottien toimintaa ja niihin vaikuttavia asioita tarkastellaan niin kinematiikan, kuin ohjelmisto- ja käskyarkkitehtuurin kautta. Työn pohjana käytettiin yliopistolla olevien KUKA robottikäsien oppaita, jotta jatkossa niiden yhteiskäyttö olisi helpommin ymmärrettävissä. Työn tulokset avasivat sitä, miten robottien ohjelmisto ohjaa ja laskee tarvittavat liikeradat ja geometriat ja mitä kaikkea usean robotin ohjauksessa pitää ottaa huomioon. Tämä on hyvä pohja syvemmälle teoreettiselle robottiohjelmistolle tai käytännön testaamiselle

Payload analysis and control of manipulators for human interactive environments

Esta tesis doctoral presenta los resultados de simulaciones numéricas y algunos análisis experimentales de tres aspectos principales: el modelamiento dinámico de manipuladores de múltiples grados de libertad (GdL) (n 2 GdL), el cálculo de la capacidad dinámica de carga asociada al manejo de dicha carga, y el análisis y diseño de controladores no lineales incluyendo el Control Adaptativo por Desfalsificación (CAD). Se desarrollaron análisis de dos (2) casos de estudio: el SCORBOT ER V PLUS fabricado por Intelitech Corp. de 5 grados de libertad y el manipulador redundante de 7 grados de libertad conocido como el Whole Arm Manipulator (WAM) fabricado por Barrett Technology Inc. y que cuenta con características de seguridad intrínseca, manipulación inversa y docilidad, y es aplicable en la interacción humano-robot (IHR). Inicialmente, se calculó y validó el modelado dinámico de los casos de estudio. Los modelos dinámicos inverso y directo del SCORBOT ER V PLUS fueron validados numéricamente. Luego, una validación experimental para el WAM presenta una comparación entre los datos numéricos y experimentales, identificando la necesidad de un mejor modelo de la fricción seca. Después, se propuso y evaluó una metodología para el cálculo de la capacidad dinámica de carga en el espacio de trabajo completo de manipuladores para diferentes tipos de controladores. Luego, para el análisis del Control Adaptativo por Desfalsificación con factor de olvido para manipuladores de múltiples grados de libertad, se realizó una comparación con un controlador adaptativo tradicional basado en el modelo y se aplicó al modelo del manipulador SCORBOR ER V PLUS. Finalmente, la técnica de Control por Desfalsificación fue exitosamente aplicada al modelo del WAM. En conclusión, este trabajo puede contribuir al uso de técnicas de control no lineal avanzado y manejo de carga para manipuladores redundantes con manipulación inversa, aplicables en ambientes de interacción con humanosAbstract : This doctoral thesis presents the results of numerical simulations and some experimental analysis of three main topics: the dynamical modeling of multiple degree of freedom (MDoF) manipulators (n 2 DoF), dynamic load carrying capacity computation (DLCC) for the payload handling issue and nonlinear control analysis and design including Unfalsified Adaptive Control (UAC). We performed analysis of two (2) cases of study: the 5 DoF SCORBOT ER V PLUS manufactured by Intelitech Corp. and the 7 DoF redundant Whole Arm Manipulator (WAM) manufactured by Barrett Technology Inc. with intrinsic safety, backdrivable and compliant characteristics and suitable for human-robot interaction (HRI). Initially, we computed and validated the dynamical model of the cases of study. The inverse and direct dynamical models of the SCORBOT ER V PLUS were numerically validated. Then, an experimental validation of inverse dynamical model of the WAM presents a comparison between numerical and experimental data, identifying the need for better friction models. After that, we proposed and evaluated a methodology for DLCC computation in the entire workspace of manipulators for different types of controllers. Then, for the analysis of the data-driven UAC with fading memory for multiple DoF manipulators, we performed a comparison with a traditional modelbased Adaptive Controller and applied to the SCORBOT ER V PLUS manipulator. Finally, the Unfalsified Control technique was successfully applied to the WAM model for a similar simulation setup. In conclusion, this work may contribute to the use of advanced nonlinear control and payload handling techniques for redundant backdrivable multiple DoF manipulators, suitable for human interactive environmentsDoctorad