Scalable hardware memory disambiguation

This dissertation deals with one of the long-standing problems in Computer Architecture – the problem of memory disambiguation. Microprocessors typically reorder memory instructions during execution to improve concurrency. Such microprocessors use hardware memory structures for memory disambiguation, known as LoadStore Queues (LSQs), to ensure that memory instruction dependences are satisfied even when the memory instructions execute out-of-order. A typical LSQ implementation (circa 2006) holds all in-flight memory instructions in a physically centralized LSQ and performs a fully associative search on all buffered instructions to ensure that memory dependences are satisfied. These LSQ implementations do not scale because they use large, fully associative structures, which are known to be slow and power hungry. The increasing trend towards distributed microarchitectures further exacerbates these problems. As on-chip wire delays increase and high-performance processors become necessarily distributed, centralized structures such as the LSQ can limit scalability. This dissertation describes techniques to create scalable LSQs in both centralized and distributed microarchitectures. The problems and solutions described in this thesis are motivated and validated by real system designs. The dissertation starts with a description of the partitioned primary memory system of the TRIPS processor, of which the LSQ is an important component, and then through a series of optimizations describes how the power, area, and centralization problems of the LSQ can be solved with minor performance losses (if at all) even for large number of in flight memory instructions. The four solutions described in this dissertation — partitioning, filtering, late binding and efficient overflow management — enable power-, area-efficient, distributed and scalable LSQs, which in turn enable aggressive large-window processors capable of simultaneously executing thousands of instructions. To mitigate the power problem, we replaced the power-hungry, fully associative search with a power-efficient hash table lookup using a simple address-based Bloom filter. Bloom filters are probabilistic data structures used for testing set membership and can be used to quickly check if an instruction with the same data address is likely to be found in the LSQ without performing the associative search. Bloom filters typically eliminate more than 80% of the associative searches and they are highly effective because in most programs, it is uncommon for loads and stores to have the same data address and be in execution simultaneously. To rectify the area problem, we observe the fact that only a small fraction of all memory instructions are dependent, that only such dependent instructions need to be buffered in the LSQ, and that these instructions need to be in the LSQ only for certain parts of the pipelined execution. We propose two mechanisms to exploit these observations. The first mechanism, area filtering, is a hardware mechanism that couples Bloom filters and dependence predictors to dynamically identify and buffer only those instructions which are likely to be dependent. The second mechanism, late binding, reduces the occupancy and hence size of the LSQ. Both of these optimizations allows the number of LSQ slots to be reduced by up to one-half compared to a traditional organization without any performance degradation. Finally, we describe a new decentralized LSQ design for handling LSQ structural hazards in distributed microarchitectures. Decentralization of LSQs, and to a large extent distributed microarchitectures with memory speculation, has proved to be impractical because of the high performance penalties associated with the mechanisms for dealing with hazards. To solve this problem, we applied classic flow-control techniques from interconnection networks for handling resource con- flicts. The first method, memory-side buffering, buffers the overflowing instructions in a separate buffer near the LSQs. The second scheme, execution-side NACKing, sends the overflowing instruction back to the issue window from which it is later re-issued. The third scheme, network buffering, uses the buffers in the interconnection network between the execution units and memory to hold instructions when the LSQ is full, and uses virtual channel flow control to avoid deadlocks. The network buffering scheme is the most robust of all the overflow schemes and shows less than 1% performance degradation due to overflows for a subset of SPEC CPU 2000 and EEMBC benchmarks on a cycle-accurate simulator that closely models the TRIPS processor. The techniques proposed in this dissertation are independent, architectureneutral and their cumulative benefits result in LSQs that can be partitioned at a fine granularity and have low design complexity. Each of these partitions selectively buffers only memory instructions with true dependences and can be closely coupled with the execution units thus minimizing power, area, and latency. Such LSQ designs with near-ideal characteristics are well suited for microarchitectures with thousands of instructions in-flight and may enable even more aggressive microarchitectures in the future.Computer Science

MxTasks: a novel processing model to support data processing on modern hardware

The hardware landscape has changed rapidly in recent years. Modern hardware in today's servers is characterized by many CPU cores, multiple sockets, and vast amounts of main memory structured in NUMA hierarchies. In order to benefit from these highly parallel systems, the software has to adapt and actively engage with newly available features. However, the processing models forming the foundation for many performance-oriented applications have remained essentially unchanged. Threads, which serve as the central processing abstractions, can be considered a "black box" that hardly allows any transparency between the application and the system underneath. On the one hand, applications are aware of the knowledge that could assist the system in optimizing the execution, such as accessed data objects and access patterns. On the other hand, the limited opportunities for information exchange cause operating systems to make assumptions about the applications' intentions to optimize their execution, e.g., for local data access. Applications, on the contrary, implement optimizations tailored to specific situations, such as sophisticated synchronization mechanisms and hardware-conscious data structures. This work presents MxTasking, a task-based runtime environment that assists the design of data structures and applications for contemporary hardware. MxTasking rethinks the interfaces between performance-oriented applications and the execution substrate, streamlining the information exchange between both layers. By breaking patterns of processing models designed with past generations of hardware in mind, MxTasking creates novel opportunities to manage resources in a hardware- and application-conscious way. Accordingly, we question the granularity of "conventional" threads and show that fine-granular MxTasks are a viable abstraction unit for characterizing and optimizing the execution in a general way. Using various demonstrators in the context of database management systems, we illustrate the practical benefits and explore how challenges like memory access latencies and error-prone synchronization of concurrency can be addressed straightforwardly and effectively

Clustered VLIW architecture based on queue register files

Institute for Computing Systems ArchitectureInstruction-level parallelism (ILP) is a set of hardware and software techniques that allow parallel execution of machine operations. Superscalar architectures rely most heavily upon hardware schemes to identify parallelism among operations. Although successful in terms of performance, the hardware complexity involved might limit the scalability of this model. VLIW architectures use a different approach to exploit ILP. In this case all data dependence analyses and scheduling of operations are performed at compile time, resulting in a simpler hardware organization. This allows the inclusion of a larger number of functional units (FUs) into a single chip. IN spite of this relative simplification, the scalability of VLIW architectures can be constrained by the size and number of ports of the register file. VLIW machines often use software pipelining techniques to improve the execution of loop structures, which can increase the register pressure. Furthermore, the access time of a register file can be compromised by the number of ports, causing a negative impact on the machine cycle time. For these reasons we understand that the benefits of having parallel FUs, which have motivated the investigation of alternative machine designs. This thesis presents a scalar VLIW architecture comprising clusters of FUs and private register files. Register files organised as queue structures are used as a mechanism for inter-cluster communication, allowing the enforcement of fixed latency in the process. This scheme presents better possibilities in terms of scalability as the size of the individual register files is not determined by the total number of FUs, suggesting that the silicon area may grow only linearly with respect to the total number of FUs. However, the effectiveness of such an organization depends on the efficiency of the code partitioning strategy. We have developed an algorithm for a clustered VLIW architecture integrating both software pipelining and code partitioning in a a single procedure. Experimental results show it may allow performance levels close to an unclustered machine without communication restraints. Finally, we have developed silicon area and cycle time models to quantify the scalability of performance and cost for this class of architecture

The Named-State Register File

This thesis introduces the Named-State Register File, a fine-grain, fully-associative register file. The NSF allows fast context switching between concurrent threads as well as efficient sequential program performance. The NSF holds more live data than conventional register files, and requires less spill and reload traffic to switch between contexts. This thesis demonstrates an implementation of the Named-State Register File and estimates the access time and chip area required for different organizations. Architectural simulations of large sequential and parallel applications show that the NSF can reduce execution time by 9% to 17% compared to alternative register files

Memory and compiler optimizations for low-power and -energy.

ICOOOLPS'2006 was co-located with the 20th European Conference on Object-Oriented Programming (ECOOP'2006).International audienceEmbedded systems become more and more widespread, especially autonomous ones, and clearly tend to be ubiquitous. In such systems, low-power and low-energy usage get ever more crucial. Furthermore, these issues also become paramount in (massively) multi-processors systems, either in one machine or more widely in a grid. The various problems faced pertain to autonomy, power supply possibilities, thermal dissipation, or even sheer energy cost. Although it has since long been studied in harware, energy optimization is more recent in software. In this paper, we thus aim at raising awareness to low-power and low-energy issues in the language and compilation community. We thus broadly but briefly survey techniques and solutions to this energy issue, focusing on a few specific aspects in the context of compiler optimizations and memory management

Dynamic Binary Translation for Embedded Systems with Scratchpad Memory

Embedded software development has recently changed with advances in computing. Rather than fully co-designing software and hardware to perform a relatively simple task, nowadays embedded and mobile devices are designed as a platform where multiple applications can be run, new applications can be added, and existing applications can be updated. In this scenario, traditional constraints in embedded systems design (i.e., performance, memory and energy consumption and real-time guarantees) are more difficult to address. New concerns (e.g., security) have become important and increase software complexity as well. In general-purpose systems, Dynamic Binary Translation (DBT) has been used to address these issues with services such as Just-In-Time (JIT) compilation, dynamic optimization, virtualization, power management and code security. In embedded systems, however, DBT is not usually employed due to performance, memory and power overhead. This dissertation presents StrataX, a low-overhead DBT framework for embedded systems. StrataX addresses the challenges faced by DBT in embedded systems using novel techniques. To reduce DBT overhead, StrataX loads code from NAND-Flash storage and translates it into a Scratchpad Memory (SPM), a software-managed on-chip SRAM with limited capacity. SPM has similar access latency as a hardware cache, but consumes less power and chip area. StrataX manages SPM as a software instruction cache, and employs victim compression and pinning to reduce retranslation cost and capture frequently executed code in the SPM. To prevent performance loss due to excessive code expansion, StrataX minimizes the amount of code inserted by DBT to maintain control of program execution. When a hardware instruction cache is available, StrataX dynamically partitions translated code among the SPM and main memory. With these techniques, StrataX has low performance overhead relative to native execution for MiBench programs. Further, it simplifies embedded software and hardware design by operating transparently to applications without any special hardware support. StrataX achieves sufficiently low overhead to make it feasible to use DBT in embedded systems to address important design goals and requirements

Hardware-software codesign in a high-level synthesis environment

Interfacing hardware-oriented high-level synthesis to software development is a computationally hard problem for which no general solution exists. Under special conditions, the hardware-software codesign (system-level synthesis) problem may be analyzed with traditional tools and efficient heuristics. This dissertation introduces a new alternative to the currently used heuristic methods. The new approach combines the results of top-down hardware development with existing basic hardware units (bottom-up libraries) and compiler generation tools. The optimization goal is to maximize operating frequency or minimize cost with reasonable tradeoffs in other properties. The dissertation research provides a unified approach to hardware-software codesign. The improvements over previously existing design methodologies are presented in the frame-work of an academic CAD environment (PIPE). This CAD environment implements a sufficient subset of functions of commercial microelectronics CAD packages. The results may be generalized for other general-purpose algorithms or environments. Reference benchmarks are used to validate the new approach. Most of the well-known benchmarks are based on discrete-time numerical simulations, digital filtering applications, and cryptography (an emerging field in benchmarking). As there is a need for high-performance applications, an additional requirement for this dissertation is to investigate pipelined hardware-software systems\u27 performance and design methods. The results demonstrate that the quality of existing heuristics does not change in the enhanced, hardware-software environment

An automated OpenCL FPGA compilation framework targeting a configurable, VLIW chip multiprocessor

Modern system-on-chips augment their baseline CPU with coprocessors and accelerators to increase overall computational capacity and power efficiency, and thus have evolved into heterogeneous systems. Several languages have been developed to enable this paradigm shift, including CUDA and OpenCL. This thesis discusses a unified compilation environment to enable heterogeneous system design through the use of OpenCL and a customised VLIW chip multiprocessor (CMP) architecture, known as the LE1. An LLVM compilation framework was researched and a prototype developed to enable the execution of OpenCL applications on the LE1 CPU. The framework fully automates the compilation flow and supports work-item coalescing to better utilise the CPU cores and alleviate the effects of thread divergence. This thesis discusses in detail both the software stack and target hardware architecture and evaluates the scalability of the proposed framework on a highly precise cycle-accurate simulator. This is achieved through the execution of 12 benchmarks across 240 different machine configurations, as well as further results utilising an incomplete development branch of the compiler. It is shown that the problems generally scale well with the LE1 architecture, up to eight cores, when the memory system becomes a serious bottleneck. Results demonstrate superlinear performance on certain benchmarks (x9 for the bitonic sort benchmark with 8 dual-issue cores) with further improvements from compiler optimisations (x14 for bitonic with the same configuration