5,435 research outputs found
Matrix Methods for the Dynamic Range Optimization of Continuous-TimeGm-CFilters
This paper presents a synthesis procedure for the optimization of the dynamic range of continuous-time fully differential G m - C filters. Such procedure builds up on a general extended state-space system representation which provides simple matrix algebra mechanisms to evaluate the noise and distortion performances of filters, as well as, the effect of amplitude and impedance scaling operations. Using these methods, an analytical technique for the dynamic range optimization of weakly nonlinear G m - C filters under power dissipation constraints is presented. The procedure is first explained for general filter structures and then illustrated with a simple biquadratic section
Stimulus-invariant processing and spectrotemporal reverse correlation in primary auditory cortex
The spectrotemporal receptive field (STRF) provides a versatile and
integrated, spectral and temporal, functional characterization of single cells
in primary auditory cortex (AI). In this paper, we explore the origin of, and
relationship between, different ways of measuring and analyzing an STRF. We
demonstrate that STRFs measured using a spectrotemporally diverse array of
broadband stimuli -- such as dynamic ripples, spectrotemporally white noise,
and temporally orthogonal ripple combinations (TORCs) -- are very similar,
confirming earlier findings that the STRF is a robust linear descriptor of the
cell. We also present a new deterministic analysis framework that employs the
Fourier series to describe the spectrotemporal modulations contained in the
stimuli and responses. Additional insights into the STRF measurements,
including the nature and interpretation of measurement errors, is presented
using the Fourier transform, coupled to singular-value decomposition (SVD), and
variability analyses including bootstrap. The results promote the utility of
the STRF as a core functional descriptor of neurons in AI.Comment: 42 pages, 8 Figures; to appear in Journal of Computational
Neuroscienc
Hardware for digitally controlled scanned probe microscopes
The design and implementation of a flexible and modular digital control and data acquisition system for scanned probe microscopes (SPMs) is presented. The measured performance of the system shows it to be capable of 14-bit data acquisition at a 100-kHz rate and a full 18-bit output resolution resulting in less than 0.02-Å rms position noise while maintaining a scan range in excess of 1 µm in both the X and Y dimensions. This level of performance achieves the goal of making the noise of the microscope control system an insignificant factor for most experiments. The adaptation of the system to various types of SPM experiments is discussed. Advances in audio electronics and digital signal processors have made the construction of such high performance systems possible at low cost
Efficient DSP and Circuit Architectures for Massive MIMO: State-of-the-Art and Future Directions
Massive MIMO is a compelling wireless access concept that relies on the use
of an excess number of base-station antennas, relative to the number of active
terminals. This technology is a main component of 5G New Radio (NR) and
addresses all important requirements of future wireless standards: a great
capacity increase, the support of many simultaneous users, and improvement in
energy efficiency. Massive MIMO requires the simultaneous processing of signals
from many antenna chains, and computational operations on large matrices. The
complexity of the digital processing has been viewed as a fundamental obstacle
to the feasibility of Massive MIMO in the past. Recent advances on
system-algorithm-hardware co-design have led to extremely energy-efficient
implementations. These exploit opportunities in deeply-scaled silicon
technologies and perform partly distributed processing to cope with the
bottlenecks encountered in the interconnection of many signals. For example,
prototype ASIC implementations have demonstrated zero-forcing precoding in real
time at a 55 mW power consumption (20 MHz bandwidth, 128 antennas, multiplexing
of 8 terminals). Coarse and even error-prone digital processing in the antenna
paths permits a reduction of consumption with a factor of 2 to 5. This article
summarizes the fundamental technical contributions to efficient digital signal
processing for Massive MIMO. The opportunities and constraints on operating on
low-complexity RF and analog hardware chains are clarified. It illustrates how
terminals can benefit from improved energy efficiency. The status of technology
and real-life prototypes discussed. Open challenges and directions for future
research are suggested.Comment: submitted to IEEE transactions on signal processin
Hardware Impairments Aware Transceiver Design for Full-Duplex Amplify-and-Forward MIMO Relaying
In this work we study the behavior of a full-duplex (FD) and
amplify-and-forward (AF) relay with multiple antennas, where hardware
impairments of the FD relay transceiver is taken into account. Due to the
inter-dependency of the transmit relay power on each antenna and the residual
self-interference in an FD-AF relay, we observe a distortion loop that degrades
the system performance when the relay dynamic range is not high. In this
regard, we analyze the relay function in presence of the hardware inaccuracies
and an optimization problem is formulated to maximize the signal to
distortion-plus-noise ratio (SDNR), under relay and source transmit power
constraints. Due to the problem complexity, we propose a
gradient-projection-based (GP) algorithm to obtain an optimal solution.
Moreover, a nonalternating sub-optimal solution is proposed by assuming a
rank-1 relay amplification matrix, and separating the design of the relay
process into multiple stages (MuStR1). The proposed MuStR1 method is then
enhanced by introducing an alternating update over the optimization variables,
denoted as AltMuStR1 algorithm. It is observed that compared to GP, (Alt)MuStR1
algorithms significantly reduce the required computational complexity at the
expense of a slight performance degradation. Finally, the proposed methods are
evaluated under various system conditions, and compared with the methods
available in the current literature. In particular, it is observed that as the
hardware impairments increase, or for a system with a high transmit power, the
impact of applying a distortion-aware design is significant.Comment: Submitted to IEEE Transactions on Wireless Communication
Wind tunnel evaluation of YF-12 inlet response to internal airflow disturbances with and without control
The response of terminal-shock position and static pressures in the subsonic duct of a YF-12 aircraft flight-hardware inlet to perturbations in simulated engine corrected airflow were obtained with and without inlet control. Frequency response data, obtained with inlet controls inactive, indicated the general nature of the inherent inlet dynamics, assisted in the design of controls, and provided a baseline reference for responses with active controls. All the control laws were implemented by means of a digital computer that could be programmed to behave like the flight inlet's existing analog control. The experimental controls were designed using an analytical optimization technique. The capabilities of the controls were limited primarily by the actuation hardware. The experimental controls provided somewhat better attenuation of terminal shock excursions than did the YF-13 inlet control. Controls using both the forward and aft bypass systems also provided somewhat better attenuation than those using just the forward bypass. The main advantage of using both bypasses is in the greater control flexibility that is achieved
- …