Cramer-Rao bounds in the estimation of time of arrival in fading channels

This paper computes the Cramer-Rao bounds for the time of arrival estimation in a multipath Rice and Rayleigh fading scenario, conditioned to the previous estimation of a set of propagation channels, since these channel estimates (correlation between received signal and the pilot sequence) are sufficient statistics in the estimation of delays. Furthermore, channel estimation is a constitutive block in receivers, so we can take advantage of this information to improve timing estimation by using time and space diversity. The received signal is modeled as coming from a scattering environment that disperses the signal both in space and time. Spatial scattering is modeled with a Gaussian distribution and temporal dispersion as an exponential random variable. The impact of the sampling rate, the roll-off factor, the spatial and temporal correlation among channel estimates, the number of channel estimates, and the use of multiple sensors in the antenna at the receiver is studied and related to the mobile subscriber positioning issue. To our knowledge, this model is the only one of its kind as a result of the relationship between the space-time diversity and the accuracy of the timing estimation.Peer ReviewedPostprint (published version

Investigations of 5G localization with positioning reference signals

TDOA is an user-assisted or network-assisted technique, in which the user equipment calculates the time of arrival of precise positioning reference signals conveyed by mobile base stations and provides information about the measured time of arrival estimates in the direction of the position server. Using multilateration grounded on the TDOA measurements of the PRS received from at least three base stations and known location of these base stations, the location server determines the position of the user equipment. Different types of factors are responsible for the positioning accuracy in TDOA method, such as the sample rate, the bandwidth, network deployment, the properties of PRS, signal propagation condition, etc. About 50 meters positioning is good for the 4G/LTE users, whereas 5G requires an accuracy less than a meter for outdoor and indoor users. Noteworthy improvements in positioning accuracy can be achievable with the help of redesigning the PRS in 5G technology. The accuracy for the localization has been studied for different sampling rates along with different algorithms. High accuracy TDOA with 5G positioning reference signal (PRS) for sample rate and bandwidth hasn’t been taken into consideration yet. The key goal of the thesis is to compare and assess the impact of different sampling rates and different bandwidths of PRS on the 5G positioning accuracy. By performing analysis with variable bandwidths of PRS in resource blocks and comparing all the analyses with different bandwidths of PRS in resource blocks, it is undeniable that there is a meaningful decrease in the RMSE and significant growth in the SNR. The higher bandwidth of PRS in resource blocks brings higher SNR while the RMSE of positioning errors also decreases with higher bandwidth. Also, the number of PRS in resource blocks provides lower SNR with higher RMSE values. The analysis with different bandwidths of PRS in resource blocks reveals keeping the RMSE value lower than a meter each time with different statistics is a positivity of the research. The positioning accuracy also analyzed with different sample sizes. With an increased sample size, a decrease in the root mean square error and a crucial increase in the SNR was observed. From this thesis investigation, it is inevitable to accomplish that two different analyses (sample size and bandwidth) done in a different way with the targeted output. A bandwidth of 38.4 MHz and sample size N = 700 required to achieve below 1m accuracy with SNR of 47.04 dB

Positioning of High-speed Trains using 5G New Radio Synchronization Signals

We study positioning of high-speed trains in 5G new radio (NR) networks by utilizing specific NR synchronization signals. The studies are based on simulations with 3GPP-specified radio channel models including path loss, shadowing and fast fading effects. The considered positioning approach exploits measurement of Time-Of-Arrival (TOA) and Angle-Of-Departure (AOD), which are estimated from beamformed NR synchronization signals. Based on the given measurements and the assumed train movement model, the train position is tracked by using an Extended Kalman Filter (EKF), which is able to handle the non-linear relationship between the TOA and AOD measurements, and the estimated train position parameters. It is shown that in the considered scenario the TOA measurements are able to achieve better accuracy compared to the AOD measurements. However, as shown by the results, the best tracking performance is achieved, when both of the measurements are considered. In this case, a very high, sub-meter, tracking accuracy can be achieved for most (>75%) of the tracking time, thus achieving the positioning accuracy requirements envisioned for the 5G NR. The pursued high-accuracy and high-availability positioning technology is considered to be in a key role in several envisioned HST use cases, such as mission-critical autonomous train systems.Comment: 6 pages, 5 figures, IEEE WCNC 2018 (Wireless Communications and Networking Conference

Radio Frequency Emitter Geolocation Using Cubesats

The ability to locate an RF transmitter is a topic of growing interest for civilian and military users alike. Geolocation can provide critical information for the intelligence community, search and rescue operators, and the warfighter. The technology required for geolocation has steadily improved over the past several decades, allowing better performance at longer baseline distances between transmitter and receiver. The expansion of geolocation missions from aircraft to spacecraft has necessitated research into how emerging geolocation methods perform as baseline distances are increased beyond what was previously considered. The CubeSat architecture is a relatively new satellite form which could enable small-scale, low-cost solutions to USAF geolocation needs. This research proposes to use CubeSats as a vehicle to perform geolocation missions in the space domain. The CubeSat form factor considered is a 6-unit architecture that allows for 6000 cm3 of space for hardware. There are a number of methods which have been developed for geolocation applications. This research compares four methods with various sensor configurations and signal properties. The four methods\u27 performance are assessed by simulating and modeling the environment, signals, and geolocation algorithms using MATLAB. The simulations created and run in this research show that the angle of arrival method outperforms the instantaneous received frequency method, especially at higher SNR values. These two methods are possible for single and dual satellite architectures. When three or more satellites are available, the direct position determination method outperforms the three other considered methods

Towards joint communication and sensing (Chapter 4)

Localization of user equipment (UE) in mobile communication networks has been supported from the early stages of 3rd generation partnership project (3GPP). With 5th Generation (5G) and its target use cases, localization is increasingly gaining importance. Integrated sensing and localization in 6th Generation (6G) networks promise the introduction of more efficient networks and compelling applications to be developed

Time of Arrival and Angle of Arrival Estimation of LTE Signals for Positioning Applications

With the increase of services that need accurate location of the user, new techniques that cooperate with the Global Navigation Satellite System (GNSS) are necessary. Toward this objective, this thesis presents our research work about the estimation of the time of arrival (TOA) and of the angle of arrival (AOA) exploiting modern cellular signals. In particular, we focus on the Third Generation Partnership Project (3GPP) Long Term Evolution (LTE) standard, and in particular uplink and downlink reference signals are exploited to this purposes. The current release of the 3GPP LTE specification supports a UTDOA localization technique based on the Sounding Reference Signal (SRS). In real environments, however, user equipments (UE) are rarely set up to transmit this particular signal. The main original contribution of this thesis consists in a new TOA estimation method based on uplink transmission. In particular, we explore the possibility of performing radio localization exploiting the uplink Demodulation Reference Signal (DM-RS), which is always sent by UEs during data transmission. Real uplink transmissions are modeled in simulations and the performance of known algorithms like SAGE and IAA-APES are evaluated for TOA estimation. A new method to estimate the initial conditions of the SAGE algorithm is proposed and the estimation performance in uplink scenarios is evaluated. The analysis revealed that the proposed method outperforms the non-coherent initial conditions estimation proposed in the literature, when uplink transmission are used. Then, the benefits of our proposal are evaluated and the feasibility of TOA estimation exploiting the DM-RS is demonstrated by means of experiments using real DM-RS signals generated by an LTE module. A second original contribution is given by AOA estimation. In particular, the independence of AOA estimation with respect to uplink and downlink transmission is verified. According to this result, the performance of IAA-APES and SAGE in real-world AOA experiments is evaluated in the downlink scenarios. Based on the overall results, we conclude that the proposed radio localization method, exploiting the uplink Demodulation Reference Signal (DM-RS), can be extended also to joint TOA, AOA using SAGE, for hybrid localization techniques. We can also conclude that the proposed method can be easily extended to downlink transmission exploiting the cell specific reference signal (CRS)

A Review of Indoor Millimeter Wave Device-based Localization and Device-free Sensing Technologies and Applications

The commercial availability of low-cost millimeter wave (mmWave) communication and radar devices is starting to improve the penetration of such technologies in consumer markets, paving the way for large-scale and dense deployments in fifth-generation (5G)-and-beyond as well as 6G networks. At the same time, pervasive mmWave access will enable device localization and device-free sensing with unprecedented accuracy, especially with respect to sub-6 GHz commercial-grade devices. This paper surveys the state of the art in device-based localization and device-free sensing using mmWave communication and radar devices, with a focus on indoor deployments. We first overview key concepts about mmWave signal propagation and system design. Then, we provide a detailed account of approaches and algorithms for localization and sensing enabled by mmWaves. We consider several dimensions in our analysis, including the main objectives, techniques, and performance of each work, whether each research reached some degree of implementation, and which hardware platforms were used for this purpose. We conclude by discussing that better algorithms for consumer-grade devices, data fusion methods for dense deployments, as well as an educated application of machine learning methods are promising, relevant and timely research directions.Comment: 43 pages, 13 figures. Accepted in IEEE Communications Surveys & Tutorials (IEEE COMST