185 research outputs found
Monitor-Based In-Field Wearout Mitigation for CMOS RF Integrated Circuits
abstract: Performance failure due to aging is an increasing concern for RF circuits. While most aging studies are focused on the concept of mean-time-to-failure, for analog circuits, aging results in continuous degradation in performance before it causes catastrophic failures. In this regard, the lifetime of RF/analog circuits, which is defined as the point where at least one specification fails, is not just determined by aging at the device level, but also by the slack in the specifications, process variations, and the stress conditions on the devices. In this dissertation, firstly, a methodology for analyzing the performance degradation of RF circuits caused by aging mechanisms in MOSFET devices at design-time (pre-silicon) is presented. An algorithm to determine reliability hotspots in the circuit is proposed and design-time optimization methods to enhance the lifetime by making the most likely to fail circuit components more reliable is performed. RF circuits are used as test cases to demonstrate that the lifetime can be enhanced using the proposed design-time technique with low area and no performance impact. Secondly, in-field monitoring and recovering technique for the performance of aged RF circuits is discussed. The proposed in-field technique is based on two phases: During the design time, degradation profiles of the aged circuit are obtained through simulations. From these profiles, hotspot identification of aged RF circuits are conducted and the circuit variable that is easy to measure but highly correlated to the performance of the primary circuit is determined for a monitoring purpose. After deployment, an on-chip DC monitor is periodically activated and its results are used to monitor, and if necessary, recover the circuit performances degraded by aging mechanisms. It is also necessary to co-design the monitoring and recovery mechanism along with the primary circuit for minimal performance impact. A low noise amplifier (LNA) and LC-tank oscillators are fabricated for case studies to demonstrate that the lifetime can be enhanced using the proposed monitoring and recovery techniques in the field. Experimental results with fabricated LNA/oscillator chips show the performance degradation from the accelerated stress conditions and this loss can be recovered by the proposed mitigation scheme.Dissertation/ThesisDoctoral Dissertation Electrical Engineering 201
NEGATIVE BIAS TEMPERATURE INSTABILITY STUDIES FOR ANALOG SOC CIRCUITS
Negative Bias Temperature Instability (NBTI) is one of the recent reliability issues in
sub threshold CMOS circuits. NBTI effect on analog circuits, which require matched
device pairs and mismatches, will cause circuit failure. This work is to assess the
NBTI effect considering the voltage and the temperature variations. It also provides a
working knowledge of NBTI awareness to the circuit design community for reliable
design of the SOC analog circuit. There have been numerous studies to date on the
NBTI effect to analog circuits. However, other researchers did not study the
implication of NBTI stress on analog circuits utilizing bandgap reference circuit. The
reliability performance of all matched pair circuits, particularly the bandgap reference,
is at the mercy of aging differential. Reliability simulation is mandatory to obtain
realistic risk evaluation for circuit design reliability qualification. It is applicable to all
circuit aging problems covering both analog and digital. Failure rate varies as a
function of voltage and temperature. It is shown that PMOS is the reliabilitysusceptible
device and NBTI is the most vital failure mechanism for analog circuit in
sub-micrometer CMOS technology. This study provides a complete reliability
simulation analysis of the on-die Thermal Sensor and the Digital Analog Converter
(DAC) circuits and analyzes the effect of NBTI using reliability simulation tool. In
order to check out the robustness of the NBTI-induced SOC circuit design, a bum-in
experiment was conducted on the DAC circuits. The NBTI degradation observed in
the reliability simulation analysis has given a clue that under a severe stress condition,
a massive voltage threshold mismatch of beyond the 2mV limit was recorded. Bum-in
experimental result on DAC proves the reliability sensitivity of NBTI to the DAC
circuitry
Degradation in FPGAs: Monitoring, Modeling and Mitigation
This dissertation targets the transistor aging degradation as well as the associated thermal challenges in FPGAs (since there is an exponential relation between aging and chip temperature). The main objectives are to perform experimentation, analysis and device-level model abstraction for modeling the degradation in FPGAs, then to monitor the FPGA to keep track of aging rates and ultimately to propose an aging-aware FPGA design flow to mitigate the aging
Cross-Layer Approaches for an Aging-Aware Design of Nanoscale Microprocessors
Thanks to aggressive scaling of transistor dimensions, computers have revolutionized our life. However, the increasing unreliability of devices fabricated in nanoscale technologies emerged as a major threat for the future success of computers. In particular, accelerated transistor aging is of great importance, as it reduces the lifetime of digital systems. This thesis addresses this challenge by proposing new methods to model, analyze and mitigate aging at microarchitecture-level and above
Recommended from our members
Physics-Based Electromigration Modeling and Analysis and Optimization
Long-term reliability is a major concern in modern VLSI design. Literature has shown that reliability gets worse as technology advances. It is expected that the future VLSI systems would have shorter reliability-induced lifetime comparing with previous generations. Being one of the most serious reliability effects, electromigration (EM) is a physical phenomenon of the migration of metal atoms due to the momentum exchange between atoms and the conducting electrons. It can cause wire resistance change or open circuit and result in functional failure of the circuit. Power-ground networks are the most vulnerable part to EM effect among all the interconnect wires since the current flow on this part is the largest on the chip. With new generation oftechnology node and aggressive design strategies, more accurate and efficient EM models are required. However, traditional EM approaches are very conservative and cannot meet current aggressive design strategies. Besides circuit level, EM also need to be thoroughly studied in system level due to limited power and temperature budgets among cores on chip. This research focuses on developing physical level EM model for VLSI circuits and system level EM optimization for multi-core systems in order to overcome the aforementioned problems. Specifically, for physical level, we develop two EM immortality check methods and a power grid EM check method. Firstly, a voltage based EM immortality analysis has been developed. Immortality condition in nucleation phase can be determined fast and accurately for multi-segment interconnect wires. Secondly, a saturation volume based incubation phase immortality check method has been proposed. This method can further reduce the redundancy in VLSI circuit design by immortality check in multiphase. Furthermore, both immortality check methods are integrated into a new power grid EM check methodology (EMspice) as filter for EM analysis. These filters can accelerate the simulation by filtering out immortal trees so that we only need to do simulation on fewer trees that are mortal. Coupled EM simulation considering both hydrostatic stress and electronic current/voltage in the power grid network will be applied to these mortal trees. This tool can work seamlessly with commercial synthesis flow. Besides physical level reliability models, system level reliability optimization is also discussed in this research. A deep reinforcement learning based EM optimization has been proposed for multi-core system. Both long term reliability effect (hard error) and transient soft error are considered. Energy can be optimized with all the reliability and other constraints fast and accurately compared to existing reliability management techniques. Last but not least, a scheduling based reliability optimization method for multi-core systems has been proposed. NBTI, HCI and EM are considered jointly. Lifetime of the system can be improved significantly compared to traditional methods which mainly focus on utilization
DEEP SUBMICRON CMOS VLSI CIRCUIT RELIABILITY MODELING, SIMULATION AND DESIGN
CMOS VLSI circuit reliability modeling and simulation have attracted intense research interest in the last two decades, and as a result almost all IC Design For Reliability (DFR) tools now try to incrementally simulate device wearout mechanisms in iterative ways. These DFR tools are capable of accurately characterizing the device wearout process and predicting its impact on circuit performance. Nevertheless, excessive simulation time and tedious parameter testing process often limit popularity of these tools in product design and fabrication.
This work develops a new SPICE reliability simulation method that shifts the focus of reliability analysis from device wearout to circuit functionality. A set of accelerated lifetime models and failure equivalent circuit models are proposed for the most common MOSFET intrinsic wearout mechanisms, including Hot Carrier Injection (HCI), Time Dependent Dielectric Breakdown (TDDB), and Negative Bias Temperature Instability (NBTI). The accelerated lifetime models help to identify the most degraded transistors in a circuit in terms of the device's terminal voltage and current waveforms. Then corresponding failure equivalent circuit models are incorporated into the circuit to substitute these identified transistors. Finally, SPICE simulation is performed again to check circuit functionality and analyze the impact of device wearout on circuit operation. Device wearout effects are lumped into a very limited number of failure equivalent circuit model parameters, and circuit performance degradation and functionality are determined by the magnitude of these parameters.
In this new method, it is unnecessary to perform a large number of small-step SPICE simulation iterations. Therefore, simulation time is obviously shortened in comparison to other tools. In addition, a reduced set of failure equivalent circuit model parameters, rather than a large number of device SPICE model parameters, need to be accurately characterized at each interim wearout process. Thus device testing and parameter extraction work are also significantly simplified. These advantages will allow circuit designers to perform quick and efficient circuit reliability analyses and to develop practical guidelines for reliable electronic designs
Identification and Rejuvenation of NBTI-Critical Logic Paths in Nanoscale Circuits
The Negative Bias Temperature Instability (NBTI) phenomenon is agreed to be one of the main reliability concerns in nanoscale circuits. It increases the threshold voltage of pMOS transistors, thus, slows down signal propagation along logic paths between flip-flops. NBTI may cause intermittent faults and, ultimately, the circuit’s permanent functional failures. In this paper, we propose an innovative NBTI mitigation approach by rejuvenating the nanoscale logic along NBTI-critical paths. The method is based on hierarchical identification of NBTI-critical paths and the generation of rejuvenation stimuli using an Evolutionary Algorithm. A new, fast, yet accurate model for computation of NBTI-induced delays at gate-level is developed. This model is based on intensive SPICE simulations of individual gates. The generated rejuvenation stimuli are used to drive those pMOS transistors to the recovery phase, which are the most critical for the NBTI-induced path delay. It is intended to apply the rejuvenation procedure to the circuit, as an execution overhead, periodically. Experimental results performed on a set of designs demonstrate reduction of NBTI-induced delays by up to two times with an execution overhead of 0.1 % or less. The proposed approach is aimed at extending the reliable lifetime of nanoelectronics
Thermal Management for Dependable On-Chip Systems
This thesis addresses the dependability issues in on-chip systems from a thermal perspective. This includes an explanation and analysis of models to show the relationship between dependability and tempature. Additionally, multiple novel methods for on-chip thermal management are introduced aiming to optimize thermal properties. Analysis of the methods is done through simulation and through infrared thermal camera measurements
- …