139 research outputs found
A 13-bit, 2.2-MS/s, 55-mW multibit cascade ΣΔ modulator in CMOS 0.7-μm single-poly technology
This paper presents a CMOS 0.7-μm ΣΔ modulator IC that achieves 13-bit dynamic range at 2.2 MS/s with an oversampling ratio of 16. It uses fully differential switched-capacitor circuits with a clock frequency of 35.2 MHz, and has a power consumption of 55 mW. Such a low oversampling ratio has been achieved through the combined usage of fourth-order filtering and multibit quantization. To guarantee stable operation for any input signal and/or initial condition, the fourth-order shaping function has been realized using a cascade architecture with three stages; the first stage is a second-order modulator, while the others are first-order modulators - referred to as a 2-1-1mb architecture. The quantizer of the last stage is 3 bits, while the other quantizers are single bit. The modulator architecture and coefficients have been optimized for reduced sensitivity to the errors in the 3-bit quantization process. Specifically, the 3-bit digital-to-analog converter tolerates 2.8% FS nonlinearity without significant degradation of the modulator performance. This makes the use of digital calibration unnecessary, which is a key point for reduced power consumption. We show that, for a given oversampling ratio and in the presence of 0.5% mismatch, the proposed modulator obtains a larger signal-to-noise-plus-distortion ratio than previous multibit cascade architectures. On the other hand, as compared to a 2-1-1single-bit modulator previously designed for a mixed-signal asymmetrical digital subscriber line modem in the same technology, the modulator in this paper obtains one more bit resolution, enhances the operating frequency by a factor of two, and reduces the power consumption by a factor of four.Comisión Interministerial de Ciencia y Tecnología TIC97-0580European Commission ESPRIT 879
Highly Linear 2,5-V CMOS ΣΔ Modulator for ADSL+
We present a 90-dB spurious-free dynamic range sigma–delta modulator (ΣΔM) for asymmetric digital subscriber line applications (both ADSL and ADSL+), with up to a 4.4-MS/s digital output rate. It uses a cascade (MASH) multibit architecture and has been implemented in a 2.5-V supply, 0.25μm CMOS process with metal–insulator–metal capacitors. The prototypes feature 78-dB dynamic range (DR) in the 30-kHz to 2.2-MHz band (ADSL+) and 85-dB DR in the 30-kHz to 1.1-MHz band (ADSL). Integral and differential nonlinearity are within +/-0.85 and +/-0.80 LSB, respectively. The ΣΔ modulator and its auxiliary blocks (clock phase and reference voltage generators, and I/O buffers) dissipate 65.8 mW. Only 55 mW are dissipated in the ΣΔ modulator.This work was supported by the European Union under IST Project 29261/MIXMODEST and IST Project 2001-34283/TAMES-2 and the Spanish MCyT and the ERDF under Project TIC2001-0929/ADAVERE.This work was supported by the European Union under IST Project 29261/MIXMODEST and IST Project 2001-34283/TAMES-2 and the Spanish MCyT and the ERDF under Project TIC2001-0929/ADAVERE.Peer reviewe
Recommended from our members
Enhanced-accuracy oversampled data converters
Digital-to-analog converters (DACs) suffer from static and dynamic nonlinearity problems, which degrade their accuracy and performance. Mismatch errors in the analog components restrict the maximum achievable linearity.
This thesis presents various techniques for correcting these errors. It describes a correction process for the nonlinear behavior of DACs, on three different levels: architectural design, circuit design, and layout design.
The main results achieved are listed below:
• Novel topologies using stochastic approaches to linearize multibit converters are presented.
• A new method is introduced for avoiding the use of multibit DACs in the main loop of multi-path DS analog-to-digital converters (ADCs), which, combined with a novel noise leakage compensation technique, allows the use of low quality inner DACs.
• A novel correction algorithm is proposed, which is based on the acquisition of the individual DAC errors by means of correlation procedures. The extracted values are used for correction purposes. The technique is capable of background operation.
• Different circuits are proposed to improve the performance of current-steering DACs. Also, novel layout techniques are shown for reducing the spatial variations of the unit sources. Some of the presented techniques were combined in a prototype chip, designed and fabricated in a 0.35μm CMOS process. Simulation and preliminary measurement results show that they are effective.Keywords: data converters, digital-to-analog, integrated circuits, analog-to-digital, CMO
Multibit delta sigma modulator with noise shaping dynamic element matching
Ph.DDOCTOR OF PHILOSOPH
Feasibility of a 16bit, 3MSPS multibit per stage pipeline ADC using digital calibration
Thesis (M. Eng.)--Massachusetts Institute of Technology, Dept. of Electrical Engineering and Computer Science; and, Thesis (B.S.)--Massachusetts Institute of Technology, Dept. of Electrical Engineering and Computer Science, 1988.Includes bibliographical references (p. 115-116).by Matthew Louis Courcy.B.S.M.Eng
Recommended from our members
High-performance delta-sigma analog-to-digital converters
Multi-stage delta-sigma (ΔΣ) architectures, commonly known as MASH, are the preferred choice for analog-to-digital converters (ADCs) used in broadband communication applications, where high-resolution (above 14 bits) and high-bandwidth (several MHz) performances are required. Current state-of-the-art designs are capable of as much as 5-MS/s output data rates with 90-dB SNR. However, inherent limitations in this type of converters have been addressed by the use of high-quality analog circuit components, making designs more complex, less robust, and higher performances difficult to achieve. This thesis describes the problems of extending bandwidth without losing accuracy in ΔΣ A/D converters, and presents three techniques which can overcome these problems: a low-distortion analog signal processing technique, the digital adaptive correction of analog circuit imperfections, and the fully digital estimation and correction of DAC errors. Combined, these techniques have the potential to achieve high-speed, high-resolution wideband ΔΣ conversion, even with low-performance analog components. The presented techniques were combined in a prototype chip, designed and fabricated in a 0.18 μm CMOS process. Simulation and preliminary measurement results show that they are highly effective
Correction of errors and harmonic distortion in pulse-width modulation of digital signals
Article number 153991Pulse-Width (PW) modulation is widely used in those applications where an analog or digital signal has to be encoded in the time domain as a binary stream, such as switched-mode power amplifiers in transmitters of modern telecommunication standards, high-resolution digital signal conversion using single-bit digital-to-analog converters, and many others. Due to the fact that digital signals are sampled in the time domain, the quality of the resulting PW modulated waveforms is worsened by harmonic distortion. Multilevel PW modulation has been proposed to reduce these adverse effects, but the modulated waveform is no longer binary. In this paper, the mechanisms by which harmonic distortion is produced are analyzed. As a result, the distortion terms are mathematically quantified and used to correct the errors. Note that a correction network based on a simple subtraction of the distortion terms from the PW modulated signal would produce a waveform that would no longer be binary. The proposed correction network is implemented in the digital domain and, by means of a sigma-delta modulator, preserves the binary feature of the PW modulated output.Ministerio de Ciencia, Innovación y Universidades (España) RTI201- 099189-B-C2
Oversampled analog-to-digital converter architectures based on pulse frequency modulation
Mención Internacional en el título de doctorThe purpose of this research work is providing new insights in the development
of voltage-controlled oscillator based analog-to-digital converters (VCO-based
ADCs). Time-encoding based ADCs have become of great interest to the designer
community due to the possibility of implementing mostly digital circuits,
which are well suited for current deep-submicron CMOS processes. Within this
topic, VCO-based ADCs are one of the most promising candidates.
VCO-based ADCs have typically been analyzed considering the output phase
of the oscillator as a state variable, similar to the state variables considered in __
modulation loops. Although this assumption might take us to functional designs
(as verified by literature), it does not take into account neither the oscillation
parameters of the VCO nor the deterministic nature of quantization noise. To
overcome this issue, we propose an interpretation of these type of systems based
on the pulse frequency modulation (PFM) theory. This permits us to analytically
calculate the quantization noise, in terms of the working parameters of the system.
We also propose a linear model that applies to VCO-based systems. Thanks to
it, we can determine the different error processes involved in the digitization of
the input data, and the performance limitations which these processes direct to.
A generic model for any order open-loop VCO-based ADCs is made based on the
PFM theory. However, we will see that only the first-order case and a second order
approximation can be implemented in practice. The PFM theory also
allows us to propose novel approaches to both single-stage and multistage VCObased
architectures. We describe open-loop architectures such as VCO-based
architectures with digital precoding, PFM-based architectures that can be used
as efficient ADCs or MASH architectures with optimal noise-transfer-function
(NTF) zeros. We also make a first approach to the proposal and analysis of closed loop
architectures. At the same time, we deal with one of the main limitations of
VCOs (especially those built with ring oscillators), which is the non-linear voltage to-
frequency relation. In this document, we describe two techniques mitigate this
phenomenon.
Firstly, we propose to use a pulse width modulator in front of the VCO. This
way, there are only two possible oscillation states. Consequently, the oscillator
works linearly. To validate the proposed technique, an experimental prototype
was implemented in a 40-nm CMOS process. The chip showed noise problems
that degraded the expected resolution, but allowed us to verify that the potential
performance was close to the expected one. A potential signal-to-noise-distortion
ratio (SNDR) equal to 56 dB was achieved in 20 MHz bandwidth, consuming
2.15 mW with an occupied area equal to 0.03 mm2. In comparison to other equivalent systems, the proposed architecture is simpler, while keeping similar
power consumption and linearity properties.
Secondly, we used a pulse frequency modulator to implement a second ADC.
The proposed architecture is intrinsically linear and uses a digital delay line to
increase the resolution of the converter. One experimental prototype was implemented
in a 40-nm CMOS process using one of these architectures. Proper results
were measured from this prototype. These results allowed us to verify that the
PFM-based architecture could be used as an efficient ADC. The measured peak
SNDR was equal to 53 dB in 20 MHz bandwidth, consuming 3.5 mW with an
occupied area equal to 0.08 mm2. The architecture shows a great linearity, and
in comparison to related work, it consumes less power and occupies similar area.
In general, the theoretical analyses and the architectures proposed in the
document are not restricted to any application. Nevertheless, in the case of the
experimental chips, the specifications required for these converters were linked to
communication applications (e.g. VDSL, VDSL2, or even G.fast), which means
medium resolution (9-10 bits), high bandwidth (20 MHz), low power and low
area.El propósito del trabajo presentado en este documento es aportar una nueva perspectiva
para el diseño de convertidores analógico-digitales basados en osciladores
controlados por tensión. Los convertidores analógico-digitales con codificación
temporal han llamado la atención durante los últimos años de la comunidad de
diseñadores debido a la posibilidad de implementarlos en su gran mayoría con
circuitos digitales, los cuales son muy apropiados para los procesos de diseño
manométricos. En este ámbito, los convertidores analógico-digitales basados en
osciladores controlados por tensión son uno de los candidatos más prometedores.
Los convertidores analógico-digitales basados en osciladores controlados por
tensión han sido típicamente analizados considerando que la fase del oscilador
es una variable de estado similar a las que se observan en los moduladores __.
Aunque esta consideración puede llevarnos a diseños funcionales (como se puede
apreciar en muchos artículos de la literatura), en ella no se tiene en cuenta ni
los parámetros de oscilación ni la naturaleza determinística del ruido de cuantificación. Para solventar esta cuestión, en este documento se propone una interpretación alternativa de este tipo de sistemas haciendo uso de la teoría de
la modulación por frecuencia de pulsos. Esto nos permite calcular de forma
analítica las ecuaciones que modelan el ruido de cuantificación en función de los
parámetros de oscilación. Se propone también un modelo lineal para el análisis de
convertidores analógico-digitales basados en osciladores controlados por tensión.
Este modelo permite determinar las diferentes fuentes de error que se producen
durante el proceso de digitalización de los datos de entrada y las limitaciones
que suponen. Un modelo genérico de convertidor de cualquier orden se propone
con la ayuda de este modelo. Sin embargo, solo los casos de primer orden y una
aproximación al caso de segundo orden se pueden implementar en la práctica.
La teoría de la modulación por frecuencia de pulsos también permite nuevas perspectivas
para la propuesta y el análisis tanto de arquitecturas de una sola etapa
como de arquitecturas de varias etapas construidas con osciladores controlados
por tensión. Se proponen y se describen arquitecturas en lazo abierto como son
las basadas en osciladores controlador por tensión con moduladores digitales en
la etapa de entrada, moduladores por frecuencia de pulsos que se utilizan como
convertidores analógico-digitales eficientes o arquitecturas en cascada en las que
se optimizan la distribución de los ceros en la función de transferencia del ruido.
También se realiza una aproximación a la propuesta y el análisis de arquitecturas
en lazo cerrado. Al mismo tiempo, se aborda una de las problemáticas más importantes
de los osciladores controlados por tensión (especialmente en aquellos
implementados mediante osciladores en anillo): la relación tensión-freculineal que presentan este tipo de circuitos. En el documento, se describen dos
técnicas cuyo objetivo es mitigar esta limitación.
La primera técnica de corrección se basa en el uso de un modulador por
ancho de pulsos antes del oscilador controlado por tensión. De esta forma, solo
existen dos estados de oscilación en el oscilador, se trabaja de forma lineal y
no se genera distorsión en los datos de salida. La técnica se propone de forma
teórica haciendo uso de la teoría desarrollada previamente. Para llevar a cabo
la validación de la propuesta teórica se fabricó un prototipo experimental en un
proceso CMOS de 40-nm. El chip mostró problemas de ruido que limitaban la
resolución, sin embargo, nos permitió velicar que la resolución ideal que se podrá
haber obtenido estaba muy cercana a la resolución esperada. Se obtuvo una
potencial relación señal-(ruido-distorsión) igual a 56 dB en 20 MHz de ancho de
banda, un consumo de 2.15 mW y un área igual a 0.03 mm2. En comparación con
sistemas equivalentes, la arquitectura propuesta es más simple al mismo tiempo
que se mantiene el consumo así como la linealidad.
A continuación, se propone la implementación de un convertidor analógico digital
mediante un modulador por frecuencia de pulsos. La arquitectura propuesta
es intrínsecamente lineal y hace uso de una línea de retraso digital con
el fin de mejorar la resolución del convertidor. Como parte del trabajo experimental,
se fabricó otro chip en tecnología CMOS de 40 nm con dicha arquitectura,
de la que se obtuvieron resultados notables. Estos resultados permitieron
verificar que la arquitectura propuesta, en efecto, podrá emplearse como convertidor
analógico-digital eficiente. La arquitectura consigue una relación real
señal-(ruido-distorsión) igual a 53 dB en 20 MHz de ancho de banda, un consumo
de 3.5 mW y un área igual a 0.08 mm2. Se obtiene una gran linealidad y, en
comparación con arquitecturas equivalentes, el consumo es menor mientras que
el área ocupada se mantiene similar.
En general, las aportaciones propuestas en este documento se pueden aplicar a
cualquier tipo de aplicación, independientemente de los requisitos de resolución,
ancho de banda, consumo u área. Sin embargo, en el caso de los prototipos
fabricados, las especificaciones se relacionan con el ámbito de las comunicaciones
(VDSL, VDSL2, o incluso G.fast), en donde se requiere una resolución media
(9-10 bits), alto ancho de banda (20 MHz), manteniendo bajo consumo y baja
área ocupada.Programa Oficial de Doctorado en Ingeniería Eléctrica, Electrónica y AutomáticaPresidente: Michael Peter Kennedy.- Secretario: Antonio Jesús López Martín.- Vocal: Jörg Hauptman
- …