Multi-Cycle Test with Partial Observation on Scan-Based BIST Structure

Field test for reliability is usually performed with small amount of memory resource, and it requires a new technique which might be somewhat different from the conventional manufacturing tests. This paper proposes a novel technique that improves fault coverage or reduces the number of test vectors that is needed for achieving the given fault coverage on scan-based BIST structure. We evaluate a multi-cycle test method that observes the values of partial flip-flops on a chip during capture-mode. The experimental result shows that the partial observation achieves fault coverage improvement with small hardware overhead than the full observation.2011 Asian Test Symposium (ATS), 20-23 Nov. 2011, New Delhi, Indi

On Flip-Flop Selection for Multi-cycle Scan Test with Partial Observation in Logic BIST

Multi-cycle test with partial observation for scan-based logic BIST is known as one of effective methods to improve fault coverage without increase of test time. In the method, the selection of flip-flops for partial observation is critical to achieve high fault coverage with small area overhead. This paper proposes a selection method under the limitation to a number of flip-flops. The method consists of structural analysis of CUT and logic simulation of test vectors, therefore, it provides an easy implementation and a good scalability. Experimental results on benchmark circuits show that the method obtains higher fault coverage with less area overhead than the original method. Also the relation between the number of selected flip-flops and fault coverage is investigated.27th IEEE ASIAN TEST SYMPOSIUM (ATS\u2718), 15-18 October 2018, Hefei, Chin

A Scan-Out Power Reduction Method for Multi-Cycle BIST

High test power in logic BIST is a serious problem not only for production test, but also for board test, system debug or field test. Many low power BIST approaches that focus on scan-shift power or capture power have been proposed. However, it is known that a half of scan-shift power is compensated by test responses, which is difficult to control in those approaches. This paper proposes a novel approach that directly reduces scan-out power by modifying some flip-flops\u27 values in scan chains at the last capture. Experimental results show that the proposed method reduces scan-out power up to 30% with little loss of test coverage.2012 IEEE 21st Asian Test Symposium, 19-22 Nov. 2012, Niigata, Japa

DFT and BIST of a multichip module for high-energy physics experiments

Engineers at Politecnico di Torino designed a multichip module for high-energy physics experiments conducted on the Large Hadron Collider. An array of these MCMs handles multichannel data acquisition and signal processing. Testing the MCM from board to die level required a combination of DFT strategie

Design for testability of a latch-based design

Abstract. The purpose of this thesis was to decrease the area of digital logic in a power management integrated circuit (PMIC), by replacing selected flip-flops with latches. The thesis consists of a theory part, that provides background theory for the thesis, and a practical part, that presents a latch register design and design for testability (DFT) method for achieving an acceptable level of manufacturing fault coverage for it. The total area was decreased by replacing flip-flops of read-write and one-time programmable registers with latches. One set of negative level active primary latches were shared with all the positive level active latch registers in the same register bank. Clock gating was used to select which latch register the write data was loaded to from the primary latches. The latches were made transparent during the shift operation of partial scan testing. The observability of the latch register clock gating logic was improved by leaving the first bit of each latch register as a flip-flop. The controllability was improved by inserting control points. The latch register design, developed in this thesis, resulted in a total area decrease of 5% and a register bank area decrease of 15% compared to a flip-flop-based reference design. The latch register design manages to maintain the same stuck-at fault coverage as the reference design.Salpaperäisen piirin testattavuuden suunnittelu. Tiivistelmä. Tämän opinnäytetyön tarkoituksena oli pienentää digitaalisen logiikan pinta-alaa integroidussa tehonhallintapiirissä, korvaamalla valitut kiikut salpapiireillä. Opinnäytetyö koostuu teoriaosasta, joka antaa taustatietoa opinnäytetyölle, ja käytännön osuudesta, jossa esitellään salparekisteripiiri ja testattavuussuunnittelun menetelmä, jolla saavutettiin riittävän hyvä virhekattavuus salparekisteripiirille. Kokonaispinta-alaa pienennettiin korvaamalla luku-kirjoitusrekistereiden ja kerran ohjelmoitavien rekistereiden kiikut salpapiireillä. Yhdet negatiivisella tasolla aktiiviset isäntä-salpapiirit jaettiin kaikkien samassa rekisteripankissa olevien positiivisella tasolla aktiivisten salparekistereiden kanssa. Kellon portittamisella valittiin mihin salparekisteriin kirjoitusdata ladattiin yhteisistä isäntä-salpapireistä. Osittaisessa testipolkuihin perustuvassa testauksessa salpapiirit tehtiin läpinäkyviksi siirtooperaation aikana. Salparekisterin kellon portituslogiikan havaittavuutta parannettiin jättämällä jokaisen salparekisterin ensimmäinen bitti kiikuksi. Ohjattavuutta parannettiin lisäämällä ohjauspisteitä. Salparekisteripiiri, joka suunniteltiin tässä diplomityössä, pienensi kokonaispinta-alaa 5 % ja rekisteripankin pinta-alaa 15 % verrattuna kiikkuperäiseen vertailupiiriin. Salparekisteripiiri onnistuu pitämään saman juuttumisvikamallin virhekattavuuden kuin vertailupiiri

A Flexible Power Control Method for Right Power Testing of Scan-Based Logic BIST

High power dissipation during scan-based logic BIST is a crucial problem that leads to over-testing. Although controlling test power of a circuit under test (CUT) to an appropriate level is strongly required, it is not easy to control test power in BIST. This paper proposes a novel power controlling method to control the toggle rate of the patterns to an arbitrary level by modifying pseudo random patterns generated by a TPG (Test Pattern Generator) of logic BIST. While many approaches have been proposed to control the toggle rate of the patterns, the proposed approach can provide higher fault coverage. Experimental results show that the proposed approach can control toggle rates to a predetermined target level and modified patterns can achieve high fault coverage without increasing test time.2016 IEEE 25th Asian Test Symposium (ATS), 21-24 Nov. 2016, Hiroshima, Japa

Design-for-delay-testability techniques for high-speed digital circuits

The importance of delay faults is enhanced by the ever increasing clock rates and decreasing geometry sizes of nowadays' circuits. This thesis focuses on the development of Design-for-Delay-Testability (DfDT) techniques for high-speed circuits and embedded cores. The rising costs of IC testing and in particular the costs of Automatic Test Equipment are major concerns for the semiconductor industry. To reverse the trend of rising testing costs, DfDT is\ud getting more and more important

フィールドにおけるテスト印加と低電力論理BISTに関する研究

Advances in semiconductor process technology have resulted in various aging issues in field operation of Very Large Scale Integration (VLSI) circuits. For example, HCI (Hot carrier injection), BTI (Bias Temperature Instability), TDDB (Time Dependent Dielectric Breakdown) are well-known aging phenomena, and they can increase the circuit delay resulting in serious reliability problems. In order to avoid system failures caused by aging, recent design usually sets a certain timing margin in operational frequency of the circuit. However, it is difficult to determine the size of the proper timing margin because of the difficulty of prediction of its aging speed in actual use that is related to operational environment. Pessimistic prediction may result in performance sacrificing although it will improve the reliability of the system. BIST-based field test is a promising way to guarantee the reliability of the circuit through detecting the aging-induced faults during the circuit operation. However, the field test has a limitation on test application time, which makes it difficult to achieve high test quality. Therefore an effective test application method at field is required. In addition to the requirement of short test application time, the BIST-based field test requires performing at-speed testing in order to detect timing-related defects. However, it is well known that power dissipation during testing is much higher than that in normal circuit operation. Because excessive power dissipation causes higher IR-drop and higher temperature, it results in delay increase during testing, and in turn, causing false at-speed testing and yield loss. While many low power test methods have been proposed to tackle the test power issue, inadequate test power reduction and lower fault coverage still remain as important issues. Moreover, low power testing that just focuses on power reduction is insufficient. When the test power is reduced to a very low level, a timing-related defect may be missed by the test, and a defective circuit will appear to be a good part passing the test. Therefore, appropriate test power control is necessary though it was out of considering in the existing methods. In this dissertation, we first proposed a new test application to satisfy the limitation of short test application time for BIST-based field test, and then we proposed a new low power BIST scheme that focuses on controlling the test power to a specified value for improving the field test quality. In chapter 3, a new field test application method named “rotating test” is presented in which a set of generated test patterns to detect aging-induced faults is partitioned into several subsets, and apply each subset in one test session at field. In order to maximize the test quality for rotating test, we proposed test partitioning methods that refer to two items: First one aims at maximizing fault coverage of each subset obtained by partitioning. Second one aims at minimizing the detection time interval of all faults in rotating test to avoid system failures. Experimental results demonstrated the effectiveness of the proposed partitioning methods. In chapter 4, we proposed a new low power BIST scheme which can control the scan-in power, scan-out power and capture power while keeping test coverage at high level. In this scheme, a new circuit called pseudo low-pass filter (PLPF) is developed for scan-in power control, and a multi-cycle capture test technique is employed to reduce the capture power. In order to control scan-out power dissipated by test responses, we proposed a novel method that selects some flip-flops in scan chains at logic design phase, and fills the selected flip-flops with proper values before starting scan-shift operation so as to reduce the switching activity associated with scan-out. The experimental results for ISCAS-89 and ITC-99 benchmark circuits show that significant scan-in power reduction rate (the original rate of 50% is reduced to 7~8%) and capture power reduction rate (the original rate of 20% is reduced to 6~7%) were derived. With the scan-out controlling method, the scan-out power can be reduced from 17.2% to 8.4%, which could not be achieved by the conventional methods. Moreover, in order to control the test power to the specified rate to accommodate the various test power requirements. A scan-shift power controlling scheme was also discussed. It showed the capability of controlling any scan-shift toggle rate between 6.7% and 50%.九州工業大学博士学位論文 学位記番号:情工博甲第289号　学位授与年月日:平成26年3月25日1. INTRODUCTION|2. PRELIMINARY|3. BIST-BASED FIELD ROTATING TEST FOR AGING-INDUCED FAULT DETECTION|4. TEST POWER REDUCTION FOR LOGIC-BIST|5. SUMMARY九州工業大学平成25年

Delay Measurements and Self Characterisation on FPGAs

This thesis examines new timing measurement methods for self delay characterisation of Field-Programmable Gate Arrays (FPGAs) components and delay measurement of complex circuits on FPGAs. Two novel measurement techniques based on analysis of a circuit's output failure rate and transition probability is proposed for accurate, precise and efficient measurement of propagation delays. The transition probability based method is especially attractive, since it requires no modifications in the circuit-under-test and requires little hardware resources, making it an ideal method for physical delay analysis of FPGA circuits. The relentless advancements in process technology has led to smaller and denser transistors in integrated circuits. While FPGA users benefit from this in terms of increased hardware resources for more complex designs, the actual productivity with FPGA in terms of timing performance (operating frequency, latency and throughput) has lagged behind the potential improvements from the improved technology due to delay variability in FPGA components and the inaccuracy of timing models used in FPGA timing analysis. The ability to measure delay of any arbitrary circuit on FPGA offers many opportunities for on-chip characterisation and physical timing analysis, allowing delay variability to be accurately tracked and variation-aware optimisations to be developed, reducing the productivity gap observed in today's FPGA designs. The measurement techniques are developed into complete self measurement and characterisation platforms in this thesis, demonstrating their practical uses in actual FPGA hardware for cross-chip delay characterisation and accurate delay measurement of both complex combinatorial and sequential circuits, further reinforcing their positions in solving the delay variability problem in FPGAs

Low Power BIST for Scan-Shift and Capture Power

Low-power test technology has been investigated deeply to achieve an accurate and efficient testing. Although many sophisticated methods are proposed for scan-test, there are not so many for logic BIST because of its uncontrollable randomness. However, logic BIST currently becomes vital for system debug or field test. This paper proposes a novel low power BIST technology that reduces shift-power by eliminating the specified high-frequency parts of vectors and also reduces capture power. The authors show that the proposed technology not only reduces test power but also keeps test coverage with little loss.2012 IEEE 21st Asian Test Symposium, 19-22 Nov. 2012, Niigata, Japa