Study of efficient transmission and reception of image-type data using millimeter waves

Evaluation of signal processing and modulation techniques for transmission and reception of image type data via millimeter wave relay satellite

Ultra Wideband

Ultra wideband (UWB) has advanced and merged as a technology, and many more people are aware of the potential for this exciting technology. The current UWB field is changing rapidly with new techniques and ideas where several issues are involved in developing the systems. Among UWB system design, the UWB RF transceiver and UWB antenna are the key components. Recently, a considerable amount of researches has been devoted to the development of the UWB RF transceiver and antenna for its enabling high data transmission rates and low power consumption. Our book attempts to present current and emerging trends in-research and development of UWB systems as well as future expectations

Integrated Distributed Amplifiers for Ultra-Wideband BiCMOS Receivers Operating at Millimeter-Wave Frequencies

Millimetre-wave technology is used for applications such as telecommunications and imaging. For both applications, the bandwidth of existing systems has to be increased to support higher data rates and finer imaging resolutions. Millimetrewave circuits with very large bandwidths are developed in this thesis. The focus is put on amplifiers and the on-chip integration of the amplifiers with antennas. Circuit prototypes, fabricated in a commercially available 130nm Silicon-Germanium (SiGe) Bipolar Complementary Metal-Oxide-Semiconductor (BiCMOS) process, validated the developed techniques. Cutting-edge performances have been achieved in the field of distributed and resonant-matched amplifiers, as well as in that of the antenna-amplifier co-integration. Examples are as follows: - A novel cascode gain-cell with three transistors was conceived. By means of transconductance peaking towards high frequencies, the losses of the synthetic line can be compensated up to higher frequencies. The properties were analytically derived and explained. Experimental demonstration validated the technique by a Traveling-Wave Amplifier (TWA) able to produce 10 dB of gain over a frequency band of 170GHz.# - Two Cascaded Single-Stage Distributed Amplifiers (CSSDAs) have been demonstrated. The first CSSDA, optimized for low power consumption, requires less than 20mW to provide 10 dB of gain over a frequency band of 130 GHz. The second amplifier was designed for high-frequency operation and works up to 250 GHz leading to a record bandwidth for distributed amplifiers in SiGe technology. - The first complete CSSDA circuit analysis as function of all key parameters was presented. The typical degradation of the CSSDA output matching towards high frequencies was analytically quantified. A balanced architecture was then introduced to retain the frequency-response advantages of CSSDAs and yet ensure matching over the frequency band of interested. A circuit prototype validated experimentally the technique. - The first traveling-wave power combiner and divider capable of operation from the MHz range up to 200 GHz were demonstrated. The circuits improved the state of the art of the maximum frequency of operation and the bandwidth by a factor of five. - A resonant-matched balanced amplifier was demonstrated with a centre frequency of 185 GHz, 10 dB of gain and a 55GHz wide –3 dB-bandwidth. The power consumption of the amplifier is 16.8mW, one of the lowest for this circuit class, while the bandwidth is the broadest reported in literature for resonant-matched amplifiers in SiGe technology

Wireless power and data transmission to high-performance implantable medical devices

Novel techniques for high-performance wireless power transmission and data interfacing with implantable medical devices (IMDs) were proposed. Several system- and circuit-level techniques were developed towards the design of a novel wireless data and power transmission link for a multi-channel inductively-powered wireless implantable neural-recording and stimulation system. Such wireless data and power transmission techniques have promising prospects for use in IMDs such as biosensors and neural recording/stimulation devices, neural interfacing experiments in enriched environments, radio-frequency identification (RFID), smartcards, near-field communication (NFC), wireless sensors, and charging mobile devices and electric vehicles. The contributions in wireless power transfer are the development of an RFID-based closed-loop power transmission system, a high-performance 3-coil link with optimal design procedure, circuit-based theoretical foundation for magnetic-resonance-based power transmission using multiple coils, a figure-of-merit for designing high-performance inductive links, a low-power and adaptive power management and data transceiver ASIC to be used as a general-purpose power module for wireless electrophysiology experiments, and a Q-modulated inductive link for automatic load matching. In wireless data transfer, the contributions are the development of a new modulation technique called pulse-delay modulation for low-power and wideband near-field data communication and a pulse-width-modulation impulse-radio ultra-wideband transceiver for low-power and wideband far-field data transmission.Ph.D

Efficient, High power Precision RF and mmWave Digital Transmitter Architectures

Digital transmitters offer several advantages over conventional analog transmitters such as reconfigurability, elimination of scaling-unfriendly, power hungry and bulky analog blocks and portability across technology. The rapid advancement of technology in CMOS processes also enables integration of complex digital signal processing circuitry on the same die as the digital transmitter to compensate for their non-idealities. The use of this digital assistance can, for instance, enable the use of highly efficient but nonlinear switching-class power amplifiers by compensating for their severe nonlinearity through digital predistortion. While this shift to digitally intensive transmitter architectures is propelled by the benefits stated above, several pressing challenges arise that vary in their nature depending on the frequency of operation - from RF to mmWave. Millimeter wave CMOS power amplifiers have traditionally been limited in output power due to the low breakdown voltage of scaled CMOS technologies and poor quality of on-chip passives. Moreover, high data-rates and efficient spectrum utilization demand highly linear power amplifiers with high efficiency under back-off. However, linearity and high efficiency are traditionally at odds with each other in conventional power amplifier design. In this dissertation, digital assistance is used to relax this trade-off and enable the use of state-of-the-art switching class power amplifiers. A novel digital transmitter architecture which simultaneously employs aggressive device-stacking and large-scale power combining for watt-class output power, dynamic load modulation for linearization, and improved efficiency under back-off by supply-switching and load modulation is presented. At RF frequencies, while the problem of watt-class power amplification has been long solved, more pressing challenges arise from the crowded spectrum in this regime. A major drawback of digital transmitters is the absence of a reconstruction filter after digital-to-analog conversion which causes the baseband quantization noise to get upconverted to RF and amplified at the output of the transmitter. In high power transmitters, this upconverted noise can be so strong as to prevent their use in FDD systems due to receiver desensitization or impose stringent coexistence challenges. In this dissertation, new quantization noise suppression techniques are presented which, for the first time, contribute toward making watt-class fully-integrated digital RF transmitters a viable alternative for FDD and coexistence scenarios. Specifically, the techniques involve embedding a mixed-domain multi-tap FIR filter within highly-efficient watt-class switching power amplifiers to suppress quantization noise, enhancing the bandwidth of noise suppression, enabling tunable location of suppression and overcoming the limitations of purely digital-domain filtering techniques for quantization noise

Application of advanced on-board processing concepts to future satellite communications systems

An initial definition of on-board processing requirements for an advanced satellite communications system to service domestic markets in the 1990's is presented. An exemplar system architecture with both RF on-board switching and demodulation/remodulation baseband processing was used to identify important issues related to system implementation, cost, and technology development

High Dimensional Modulation and MIMO Techniques for Access Networks

Exploration of advanced modulation formats and multiplexing techniques for next generation optical access networks are of interest as promising solutions for delivering multiple services to end-users. This thesis addresses this from two different angles: high dimensionality carrierless amplitudephase (CAP) and multiple-input multiple-output (MIMO) radio-over-fiber (RoF) systems. High dimensionality CAP modulation has been investigated in optical fiber systems. In this project we conducted the first experimental demonstration of 3 and 4 dimensional CAP with bit rates up to 10 Gb/s. These results indicate the potentiality of supporting multiple users with converged services. At the same time, orthogonal division multiple access (ODMA) systems for multiple possible dimensions of CAP modulation has been demonstrated for user and service allocation in wavelength division multiplexing (WDM) optical access network. 2 x 2 MIMO RoF employing orthogonal frequency division multiplexing (OFDM) with 5.6 GHz RoF signaling over all-vertical cavity surface emitting lasers (VCSEL) WDM passive optical networks (PONs). We have employed polarization division multiplexing (PDM) to further increase the capacity per wavelength of the femto-cell network. Bit rate up to 1.59 Gbps with fiber-wireless transmission over 1 m air distance is demonstrated. The results presented in this thesis demonstrate the feasibility of high dimensionality CAP in increasing the number of dimensions and their potentially to be utilized for multiple service allocation to different users. MIMO multiplexing techniques with OFDM provides the scalability in increasing spectral effciency and bit rates for RoF systems. High dimensional CAP and MIMO multiplexing techniques are two promising solutions for supporting wired and hybrid wired-wireless access networks

Customer premise service study for 30/20 GHz satellite system

Satellite systems in which the space segment operates in the 30/20 GHz frequency band are defined and compared as to their potential for providing various types of communications services to customer premises and the economic and technical feasibility of doing so. Technical tasks performed include: market postulation, definition of the ground segment, definition of the space segment, definition of the integrated satellite system, service costs for satellite systems, sensitivity analysis, and critical technology. Based on an analysis of market data, a sufficiently large market for services is projected so as to make the system economically viable. A large market, and hence a high capacity satellite system, is found to be necessary to minimize service costs, i.e., economy of scale is found to hold. The wide bandwidth expected to be available in the 30/20 GHz band, along with frequency reuse which further increases the effective system bandwidth, makes possible the high capacity system. Extensive ground networking is required in most systems to both connect users into the system and to interconnect Earth stations to provide spatial diversity. Earth station spatial diversity is found to be a cost effective means of compensating the large fading encountered in the 30/20 GHz operating band

60 GHz transceiver circuits in SiGe-HBT and CMOS technologies

Die Erhöhung der Übertragungsrate von Kommunikationssystemen ist von hohem wissenschaftlichem und wirtschaftlichem Interesse. Die stetige Fortentwicklung dieser Systeme, sowohl unter Aspekten der Hard- als auch der Software, hat ein neues Technologiezeitalter eingeläutet. Verschiedene Szenarien, auf optischen, drahtgebundenen und drahtlosen Technologien basierend, wurden für diese Anwendungen entwickelt. Im 60 GHz ISM-Band (57 GHz bis 65 GHz) ist wegen der hohen Absorptionsverluste bei dieser Frequenz eine Kurzstrecken-Kommunikation mit hoher Datenrate von besonders hohem Interesse. Die Realisierung solcher Systeme erfolgt aufgrund von Kosten- und Massenproduktionsaspekten auf Basis von SiGe-HBT und CMOS Technologien. Schlüsselparameter eines 60 GHz-Transceivers sind eine hohe Ausgangsleistung, niedrige Rauschzahl, geringer Stromverbrauch und niedrige Herstellungskosten. Um den gesamten Frequenzbereich des 60 GHz ISM-Bandes abdecken zu können, wurden zahlreiche Transceivertopologien weltweit diskutiert. Die verfügbare Technologie mit ihren Schlüsselparametern ft, fmax stellt hierbei eine wichtige Randbedingung dar. In dieser Arbeit werden Aspekte des 60 GHz-Transceiver-Designs unter Verwendung einer 0,25 μm SiGe-HBT- und einer 90 nm CMOS-Technologie untersucht. Zunächst wird die Modellierung von passiven und aktiven Komponenten diskutiert. Verschiedene Techniken zur Modellextraktion basierend auf Messungen und elektromagnetischen Simulationen werden gezeigt. Für die wichtigsten passiven Bauelemente werden skalierbare Modelle entwickelt, um das Entwurfsverfahren zu präzisieren. Im nächsten Schritt werden 60 GHz CMOS- und SiGe-HBT- Leistungsverstärker untersucht. Basierend auf diesen Studien wurden zwei HBT und zwei CMOS-Endstufen konzipiert, realisiert und gemessen. Infolge der Verfügbarkeit einer hochgenauen Bauelemente-Bibliothek, ausgereifter Entwurfstechniken und der Verifikation auf Basis von EM-Simulationen konnte an den gemessenen Leistungsverstärkern eine hohe Ausgangsleistung mit guter Effizienz nachgewiesen werden. Die Ergebnisse zeigen weiterhin eine gute Übereinstimmung von Simulationen mit Messungen. Weiterhin wurden auf Basis einer 90 nm CMOS Technologie ein Heterodyne und ein OOK Transceiver entwickelt. Der Heterodyne-Transceiver mit einer Zwischenfrequenz von 20 GHz genügt dabei dem IEEE 802.15.3c Standard und erreicht eine Performance auf Höhe des internationalen Standes von Wissenschaft und Technik. Für den OOK Sender wurde eine neue Topologie entwickelt. Bei diesem Konzept bilden Modulator und Leistungsverstärker eine Einheit, woraus Vorteile hinsichtlich Ausgangsleistung, Effizienz und Chipgröße resultieren. Mit dieser Schaltung wurde in einem Systemtest eine Übertragungsrate von 6 Gbps über eine Entfernung von 4 m erfolgreich nachgewiesen.The rise of high-data-rate hungry applications has brought a new dawn to telecommunication technologies in both hardware and software development aspects. Different scenarios, mainly based on optical, coaxial and wireless systems, have been developed for these multi-gigabit communication systems. In these scenarios, the wireless system is utilized for indoor and short-range communication, which can ease the requirements on RF power and noise figure of the transceivers. However, the demand for multi-gigabit communication imposes a broadband performance requirement upon these wireless transceivers. This broadband performance requirement can be within the range of 2 GHz to 10 GHz. In order to cover such a broad frequency range, different transceiver circuit topologies have been suggested by many circuit designers. Due to the high oxygen loss in the 60 GHz range this 57 GHz to 65 GHz ISM band has attracted attention for high speed short-range communication. Moreover, the newly emerged low cost technologies (like, CMOS and SiGe HBT) have further attracted the industry to explore this communication band. The main requirements for a 60 GHz transceiver are high output power, low noise figure, low power consumption and broadband performance. To cover the whole 57 GHz to 65 GHz frequency band, numerous transceiver topologies are under discussion. The key parameter ft, fmax of the available technology define the achievable system performance. In this thesis, multiple aspects of the 60 GHz transceiver design based on the 90 nm CMOS and 0.25 μm SiGe HBT designs have been investigated. First, the modeling of passive and active components is presented. These components include capacitors, inductors, transformers, transmission lines, transistors, matching networks and RF pads. Different techniques for model extraction based on measurements and electromagnetic simulations have been examined. For inductors, transformers and capacitors scalable models have been developed. Further, the design techniques of 60 GHz CMOS and SiGe HBT power amplifiers have been studied. Based on these studies, two HBT and two CMOS power amplifiers have been designed, realized and measured. Due to accurate modeling and design techniques, high performance and good agreement with simulation has been achieved. Finally, two different types of transmitters (Heterodyne and OOK) based on the CMOS technology have been developed. The heterodyne transceiver, with an IF frequency of around 20 GHz, has been designed based on the IEEE 802.15.3c standard. This transmitter has achieved state of the art results with respect to output power, conversion gain and efficiency with a small chip size and low power consumption. For the OOK transmitter, a novel topology has been developed. In this topology, the modulator and the power amplifier have been integrated into one circuit. Due to many advantages of this new topology, this transmitter achieves higher output power and efficiency compared with state-of-the-art results. Furthermore, the realized circuit has been utilized within a wireless system where more than 6 Gbps has been successfully transmitted over a 4 m distance

Substrate Integrated Waveguide Devices and Receiver Systems for Millimeter-Wave Applications

RÉSUMÉ La très forte congestion du spectre radiofréquence alloué aux fréquences RF et micro-ondes pour les communications sans fil d’aujourd’hui motive ce travail de recherche qui se consacre aux bandes millimétriques pour lesquelles d’avantages d’allocations spectrales sont disponibles, et qui est particulièrement intéressante pour le transfert à très haut débit. Comparé aux autres technologies de ligne de transmission, le Guide Intégré au Substrat (GIS) montre des avantages très attractifs comme un faible profil, un faible coût, un haut facteur de qualité (facteur Q), de faibles pertes d’insertion... Ce dernier a gagné beaucoup d’attention récemment grâce à ces caractéristiques favorables pour la conception de circuits et systèmes millimétriques. Le sujet de ce doctorat concerne deux tâches de recherche distinctes : la première est dédiée à l’investigation et à la conception de composants et d’antennes GIS innovants pour une possible application en ondes millimétriques; la seconde se consacre à la mise au point et à la démonstration de systèmes de réceptions millimétriques de tailles compactes, faibles pertes, à haut niveau d’intégration et hautes performances. Les chapitres 1 à 4 se concentrent sur l’exploitation et l’investigation, un à un, de composants GIS pour lesquels un nombre de concepts originaux et innovants de structures est proposé et démontré. Dans le chapitre 5, les architectures classiques et les paramètres des systèmes de réception sont introduits, puis utilisés pour la conception de systèmes de réceptions millimétriques dans les chapitres suivants. Du chapitre 6 au chapitre 8, des systèmes submillimétriques et millimétriques basés sur le GIS sont démontrés. Les contributions majeures de cette thèse sont les suivantes : Une structure balancée large bande inhérente peut être obtenue en imprimant un circuit sur deux faces d’un substrat GIS. Ainsi, un balun planaire large bande GIS implémenté sur un circuit imprimé (ou PCB, pour Printed Circuit Board) simple couche est proposé et présenté, suite auquel une nouvelle transition large bande de ligne microruban à ligne parallèle est démontrée. Avec cette transition proposée comme réseau d’alimentation, une nouvelle antenne large bande quasi-Yagi planaire est développée.----------ABSTRACT The heavily congested condition at the existing radio frequency (RF)/microwave spectra allocated for the today’s wireless communications motivates and expedites the research work at millimeter-wave bands where more spectrum space is available for massive data rate delivery. Compared with other transmission line techniques, the substrate integrated waveguide (SIW) platform shows attractive advantages of low profile, low-cost, high Q-factor, and low insertion loss, etc. It has gained a lot of attention recently due to its favorable features in millimeter-wave circuit/system design. The topic of this doctoral dissertation are concerned with two distinct research tasks: (1) investigating and designing innovative SIW components and antennas for possible millimeter-wave applications; (2) developing and demonstrating geometry-compact, low cost, high level of integration and high performance millimeter-wave receiver systems. Chapters 1 to 4 focus on the exploitation and investigation of individual SIW devices, in which a number of original concepts and innovative structures are proposed and demonstrated. In Chapter 5, generic architectures and parameters of receiver systems are discussed and used as a guideline for the millimeter-wave system design in the next chapters. From Chapter 6 to Chapter 8, sub-millimeter/millimeter wave systems based on SIW technique are demonstrated. The major contributions of this thesis work can be highlighted as follows:An inherent broadband balanced structure can be achieved by printing circuits on two opposite sides of an SIW substrate. According to this feature, a broadband SIW planar balun implemented on a single layer printed circuit board (PCB) is proposed and presented, following which another newly proposed broadband microstrip-to-broadside parallel stripline transition is demonstrated. With the proposed transition as the feeding network, a novel broadband printed quasi-Yagi antenna is developed. Half-mode substrate integrated waveguide (HMSIW) and quarter-mode substrate integrated waveguide (QMSIW) techniques are introduced for the purpose of miniaturizing SIW circuits and enhancing the bandwidth