2,063 research outputs found
Nonlinear control for Two-Link flexible manipulator
Recently the use of robot manipulators has been increasing in many applications such as medical applications, automobile, construction, manufacturing, military, space, etc. However, current rigid manipulators have high inertia and use actuators with large energy consumption. Moreover, rigid manipulators are slow and have low payload-to arm-mass ratios because link deformation is not allowed. The main advantages of flexible manipulators over rigid manipulators are light in weight, higher speed of operation, larger workspace, smaller actuator, lower energy consumption and lower cost. However, there is no adequate closed-form solutions exist for flexible manipulators. This is mainly because flexible dynamics are modeled with partial differential equations, which give rise to infinite dimensional dynamical systems that are, in general, not possible to represent exactly or efficiently on a computer which makes modeling a challenging task. In addition, if flexibility nature wasn\u27t considered, there will be calculation errors in the calculated torque requirement for the motors and in the calculated position of the end-effecter. As for the control task, it is considered as a complex task since flexible manipulators are non-minimum phase system, under-actuated system and Multi-Input/Multi-Output (MIMO) nonlinear system. This thesis focuses on the development of dynamic formulation model and three control techniques aiming to achieve accurate position control and improving dynamic stability for Two-Link Flexible Manipulators (TLFMs). LQR controller is designed based on the linearized model of the TLFM; however, it is applied on both linearized and nonlinear models. In addition to LQR, Backstepping and Sliding mode controllers are designed as nonlinear control approaches and applied on both the nonlinear model of the TLFM and the physical system. The three developed control techniques are tested through simulation based on the developed dynamic formulation model using MATLAB/SIMULINK. Stability and performance analysis were conducted and tuned to obtain the best results. Then, the performance and stability results obtained through simulation are compared. Finally, the developed control techniques were implemented and analyzed on the 2-DOF Serial Flexible Link Robot experimental system from Quanser and the results are illustrated and compared with that obtained through simulation
A Certified-Complete Bimanual Manipulation Planner
Planning motions for two robot arms to move an object collaboratively is a
difficult problem, mainly because of the closed-chain constraint, which arises
whenever two robot hands simultaneously grasp a single rigid object. In this
paper, we propose a manipulation planning algorithm to bring an object from an
initial stable placement (position and orientation of the object on the support
surface) towards a goal stable placement. The key specificity of our algorithm
is that it is certified-complete: for a given object and a given environment,
we provide a certificate that the algorithm will find a solution to any
bimanual manipulation query in that environment whenever one exists. Moreover,
the certificate is constructive: at run-time, it can be used to quickly find a
solution to a given query. The algorithm is tested in software and hardware on
a number of large pieces of furniture.Comment: 12 pages, 7 figures, 1 tabl
Recommended from our members
An efficient finite element formulation of dynamics for a flexible robot with different type of joints
If two adjacent links of a flexible robot are connected via a revolute joint or a fixed prismatic joint, the relative motion of the next link will depend on both the joint motion and the elastic displacement of the distal end of the previous link. However, if the two adjacent links are connected via a sliding prismatic joint, the relative motion of the next link will depend additionally on the elastic deformation distributed along the previous link. Therefore, formulation of the motion equations for a multi-link flexible robot consisting of the revolute joints, the fixed prismatic joints and the sliding prismatic joints is challenging. In this study, the finite element kinematic and dynamic formulation was successfully developed and validated for the flexible robot, in which a transformation matrix is proposed to describe the kinematics of both the joint motion and the link deformation. Additionally, a new recursive formulation of the dynamic equations is introduced. As compared with the previous methods, the time complexity of the formulation is reduced by O(2η), where η is the number of finite elements on all links. The numerical examples and experiments were implemented to validate the proposed kinematic and dynamic modelling method
Advanced Strategies for Robot Manipulators
Amongst the robotic systems, robot manipulators have proven themselves to be of increasing importance and are widely adopted to substitute for human in repetitive and/or hazardous tasks. Modern manipulators are designed complicatedly and need to do more precise, crucial and critical tasks. So, the simple traditional control methods cannot be efficient, and advanced control strategies with considering special constraints are needed to establish. In spite of the fact that groundbreaking researches have been carried out in this realm until now, there are still many novel aspects which have to be explored
A supervisory sliding mode control approach for cooperative robotic system of systems
This paper deals with the formulation of a supervisory sliding mode (SM) control approach oriented to deal with the interesting class of system of systems of robotic nature. This class of systems is characterized by the fact of being inherently distributed, cooperative, and, possibly, heterogeneous. In this paper, we propose a modular and composable approach relying on basic modules featuring a multilevel functional architecture, including a supervisor and a couple of hybrid position/force control schemes associated with a couple of cooperative robotic manipulators. In principle, the overall robotic system we are referring to can be viewed as a collection of basic modules of that type. In this paper, we focus on the design of the basic module. The hybrid position/force control schemes therein included are based on position and force controllers. The proposed position and force controllers are of SM type, to assure suitable robustness to perform a satisfactory trajectory tracking even in presence of unavoidable modeling uncertainties and external disturbances. The verification and the validation of our proposal have been performed by simulating the supervisor and the hybrid control scheme applied to one of the two robotic manipulators while experimentally testing the position control on the other arm. The experimental part of the tests has been carried out on a COMAU SMART3-S2 anthropomorphic industrial robotic manipulator
Design of an Integral Suboptimal Second-Order Sliding Mode Controller for the Robust Motion Control of Robot Manipulators
The formulation of an integral suboptimal second-order sliding mode ((ISSOSM) control algorithm, oriented to solve motion control problems for robot manipulators, is presented in this paper. The proposed algorithm is designed so that the so-called reaching phase, normally present in the evolution of a system controlled via the sliding mode approach, is reduced to a minimum. This fact makes the algorithm more suitable to be applied to a real industrial robot, since it enhances its robustness, by extending it also to time intervals during which the classical sliding mode is not enforced. Moreover, since the algorithm generates second-order sliding modes, while the model of the controlled electromechanical system has a relative degree equal to one, the control action actually fed into the plant is continuous, which provides a positive chattering alleviation effect. The assessment of the proposal has been carried out by experimentally testing it on a COMAU SMART3-S2 anthropomorphic industrial robot manipulator. The satisfactory experimental results, also compared with those obtained with a standard proportional-derivative controller and with the original suboptimal algorithm, confirm that the new algorithm can actually be used in an industrial context
Modeling and Control of Flexible Link Manipulators
Autonomous maritime navigation and offshore operations have gained wide attention with the aim of reducing operational costs and increasing reliability and safety. Offshore operations, such as wind farm inspection, sea farm cleaning, and ship mooring, could be carried out autonomously or semi-autonomously by mounting one or more long-reach robots on the ship/vessel. In addition to offshore applications, long-reach manipulators can be used in many other engineering applications such as construction automation, aerospace industry, and space research. Some applications require the design of long and slender mechanical structures, which possess some degrees of flexibility and deflections because of the material used and the length of the links. The link elasticity causes deflection leading to problems in precise position control of the end-effector. So, it is necessary to compensate for the deflection of the long-reach arm to fully utilize the long-reach lightweight flexible manipulators.
This thesis aims at presenting a unified understanding of modeling, control, and application of long-reach flexible manipulators. State-of-the-art dynamic modeling techniques and control schemes of the flexible link manipulators (FLMs) are discussed along with their merits, limitations, and challenges. The kinematics and dynamics of a planar multi-link flexible manipulator are presented. The effects of robot configuration and payload on the mode shapes and eigenfrequencies of the flexible links are discussed. A method to estimate and compensate for the static deflection of the multi-link flexible manipulators under gravity is proposed and experimentally validated. The redundant degree of freedom of the planar multi-link flexible manipulator is exploited to minimize vibrations. The application of a long-reach arm in autonomous mooring operation based on sensor fusion using camera and light detection and ranging (LiDAR) data is proposed.publishedVersio
- …