Modelling and simulation of paradigms for printed circuit board assembly to support the UK's competency in high reliability electronics

The fundamental requirement of the research reported within this thesis is the provision of physical models to enable model based simulation of mainstream printed circuit assembly (PCA) process discrete events for use within to-be-developed (or under development) software tools which codify cause & effects knowledge for use in product and process design optimisation. To support a national competitive advantage in high reliability electronics UK based producers of aircraft electronic subsystems require advanced simulation tools which offer model based guidance. In turn, maximization of manufacturability and minimization of uncontrolled rework must therefore enhance inservice sustainability for ‘power-by-the-hour’ commercial aircraft operation business models. [Continues.

Introduction to Surface-Mount Technology

In chapter 1, the surface-mount technology and reflow soldering technology are overviewed. A brief introduction is presented into the type of electronic components, including through-hole- and surface-mounted ones. Steps of reflow soldering technology are outlined, and details are given regarding the properties of solder material in this technology. The rheological behavior of solder pastes is detailed, and some recent advancements in addressing the thixotropic behavior of this material are summarized. The process of stencil printing is detailed next, which is the most crucial step in reflow soldering technology; since even 60–70% of the soldering failures can be traced back to this process. The topic includes the structures of stencils, discussion of the primary process parameters, and process optimization possibilities by numerical modeling. Process issues of component placement are presented. The critical parameter (process and machines capability), which is used extensively for characterizing the placement process is studied. In connection with the measurement of process capability, the method of Gage R&R (repeatability and reproducibility) is detailed, including the estimation of respective variances. Process of the reflow soldering itself is detailed, including the two main phenomena taking place when the solder is in the molten state, namely: wetting of the liquid solder due to surface tension, and intermetallic compound formation due to diffusion. Solder profile calculation and component movements during the soldering (e.g., self-alignment of passive components) are presented too. Lastly, the pin-in-paste technology (reflow solder of through-hole components) is detailed, including some recent advancements in the optimization of this technology by utilizing machine learning techniques

Numerical Simulation of Condensate Layer Formation During Vapour Phase Soldering

This paper presents a modeling approach of the condensate layer formation on the surface of printed circuit boards during Vapour Phase Soldering (VPS) process. The condensate layer formation model is an extension to a previously developed board level condensation model, which calculates the mass of the condensed material on the surface of the soldered printed circuit board. The condensate layer formation model applies combined transport mechanisms including convective mass transport due to the hydrostatic pressure difference in the layer and the gravity force; conductive and convective energy transport. The model can describe the dynamic formation and change of the condensate layer after the immersion of the soldered assembly into the saturated vapour space and can calculate the mass and energy transport in the formed condensate layer. This way the effect of the condensate layer changes on the heating of the soldered assembly can be investigated. It was shown that the numerical modeling of the VPS process becomes more accurate with application of dynamic condensate layer instead of a static description

Soldering Characteristics And Thermomechanical Properties Of Pb-Free Solder Paste For Reflow Soldering

A deep understanding in thermal characteristics of lead-free solder paste grades is one of the most crucial factors when dealing with reflow soldering process. These temperatures are critical parameters for proper settings of the real reflow process. This report is devoted to discussing the findings obtained during utilization of differential scanning calorimetry (DSC) and calculation using MATLAB to identify the latent heat, solidus and liquidus temperature, and surface tension applicable to numerically simulate the real process of reflow soldering. It can be stated that the equilibrium solidus and liquidus temperatures during solidification process are not a reversal of the melting process, with the solid phase equilibrium occurred at a lower temperature due to the difficulty of ß-Sn nucleation. Amount of heat energy released during solidification differs less than 10% for SAC405 and less than 1% for SAC105 with the latent heat of fusion during the melting process

Optoelectronic devices and packaging for information photonics

This thesis studies optoelectronic devices and the integration of these components onto optoelectronic multi chip modules (OE-MCMs) using a combination of packaging techniques. For this project, (1×12) array photodetectors were developed using PIN diodes with a GaAs/AlGaAs strained layer structure. The devices had a pitch of 250μm, operated at a wavelength of 850nm. Optical characterisation experiments of two types of detector arrays (shoe and ring) were successfully performed. Overall, the shoe devices achieved more consistent results in comparison with ring diodes, i.e. lower dark current and series resistance values. A decision was made to choose the shoe design for implementation into the high speed systems demonstrator. The (1x12) VCSEL array devices were the optical sources used in my research. This was an identical array at 250μm pitch configuration used in order to match the photodetector array. These devices had a wavelength of 850nm. Optoelectronic testing of the VCSEL was successfully conducted, which provided good beam profile analysis and I-V-P measurements of the VCSEL array. This was then implemented into a simple demonstrator system, where eye diagrams examined the systems performance and characteristics of the full system and showed positive results. An explanation was given of the following optoelectronic bonding techniques: Wire bonding and flip chip bonding with its associated technologies, i.e. Solder, gold stud bump and ACF. Also, technologies, such as ultrasonic flip chip bonding and gold micro-post technology were looked into and discussed. Experimental work implementing these methods on packaging the optoelectronic devices was successfully conducted and described in detail. Packaging of the optoelectronic devices onto the OEMCM was successfully performed. Electrical tests were successfully carried out on the flip chip bonded VCSEL and Photodetector arrays. These results verified that the devices attached on the MCM achieved good electrical performance and reliable bonding. Finally, preliminary testing was conducted on the fully assembled OE-MCMs. The aim was to initially power up the mixed signal chip (VCSEL driver), and then observe the VCSEL output

SOLDERING CHARACTERISTICS AND THERMO- MECHANICAL PROPERTIES OF Pb-FREE SOLDER PASTE FOR REFLOW SOLDERING

A deep understanding in thermal characteristics of lead-free solder paste grades is one of the most crucial factors when dealing with reflow soldering process. These temperatures are critical parameters for proper settings of the real reflow process. This report is devoted to discussing the findings obtained during utilization of differential scanning calorimetry (DSC) and calculation using MATLAB to identify the latent heat, solidus and liquidus temperature, and surface tension  applicable to numerically simulate the real process of reflow soldering. It can be stated that the equilibrium solidus and liquidus temperatures during solidification process are not a reversal of the melting process, with the solid phase equilibrium occurred at a lower temperature due to the difficulty of ß-Sn nucleation. Amount of heat energy released during solidification differs less than 10% for SAC405 and less than 1% for SAC105 with the latent heat of fusion during the melting process

A Digital Manufacturing Process For Three-Dimensional Electronics

Additive manufacturing (AM) offers the ability to produce devices with a degree of three-dimensional complexity and mass customisation previously unachievable with subtractive and formative approaches. These benefits have not transitioned into the production of commercial electronics that still rely on planar, template-driven manufacturing, which prevents them from being tailored to the end user or exploiting conformal circuitry for miniaturisation. Research into the AM fabrication of 3D electronics has been demonstrated; however, because of material restrictions, the durability and electrical conductivity of such devices was often limited. This thesis presents a novel manufacturing approach that hybridises the AM of polyetherimide (PEI) with chemical modification and selective light-based synthesis of silver nanoparticles to produce 3D electronic systems. The resulting nanoparticles act as a seed site for the electroless deposition of copper. The use of high-performance materials for both the conductive and dielectric elements created devices with the performance required for real-world applications. For printing PEI, a low-cost fused filament fabrication (FFF); also known as fused deposition modelling (FDM), printer with a unique inverted design was developed. The orientation of the printer traps hot air within a heated build environment that is open on its underside allowing the print head to deposit the polymer while keeping the sensitive components outside. The maximum achievable temperature was 120 °C and was found to reduce the degree of warping and the ultimate tensile strength of printed parts. The dimensional accuracy was, on average, within 0.05 mm of a benchmark printer and fine control over the layer thickness led to the discovery of flexible substrates that can be directly integrated into rigid parts. Chemical modification of the printed PEI was used to embed ionic silver into the polymer chain, sensitising it to patterning with a 405 nm laser. The rig used for patterning was a re-purposed vat-photopolymerisation printer that uses a galvanometer to guide the beam that is focused to a spot size of 155 µm at the focal plane. The positioning of the laser spot was controlled with an open-sourced version of the printers slicing software. The optimal laser patterning parameters were experimentally validated and a link between area-related energy density and the quality of the copper deposition was found. In tests where samples were exposed to more than 2.55 J/cm^2, degradation of the polymer was experienced which produced blistering and delamination of the copper. Less than 2.34 J/cm^2 also had negative effect and resulted in incomplete coverage of the patterned area. The minimum feature resolution produced by the patterning setup was 301 µm; however, tests with a photomask demonstrated features an order of magnitude smaller. The non-contact approach was also used to produce conformal patterns over sloped and curved surfaces. Characterisation of the copper deposits found an average thickness of 559 nm and a conductivity of 3.81 × 107 S/m. Tape peel and bend fatigue testing showed that the copper was ductile and adhered well to the PEI, with flexible electronic samples demonstrating over 50,000 cycles at a minimum bend radius of 6.59 mm without failure. Additionally, the PEI and copper combination was shown to survive a solder reflow with peak temperatures of 249°C. Using a robotic pick and place system a test board was automatically populated with surface mount components as small as 0201 resistors which were affixed using high-temperature, Type-V Tin-Silver-Copper solder paste. Finally, to prove the process a range of functional demonstrators were built and evaluated. These included a functional timer circuit, inductive wireless power coils compatible with two existing standards, a cylindrical RF antenna capable of operating at several frequencies below 10 GHz, flexible positional sensors, and multi-mode shape memory alloy actuators