Immediate Analysis of Periodic Steady States in Switched DC-DC Converters via SPICE

The method of immediate analysis of periodic steady states in switched DC-DC converters operating in the continuous current mode is described. The initial conditions, which correspond to the periodic steady state, are found in the first step. They are used consequently for the conventional transient analysis. A special SPICE model of the converter finds automatically these initial conditions, which are then available within the transient analysis. The method works both for the well-known behavioral models of switched converters and also for models which employ complex nonlinear SPICE models of semiconductor switches

Passivity-based harmonic control through series/parallel damping of an H-bridge rectifier

Nowadays the H-bridge is one of the preferred solutions to connect DC loads or distributed sources to the single-phase grid. The control aims are: sinusoidal grid current with unity power factor and optimal DC voltage regulation capability. These objectives should be satisfied, regardless the conditions of the grid, the DC load/source and the converter nonlinearities. In this paper a passivity-based approach is thoroughly investigated proposing a damping-based solution for the error dynamics. Practical experiments with a real converter validate the analysis.

Switched Capacitor Voltage Converter

This project supports IoT development by reducing the power con- sumption and physical footprint of voltage converters. Our switched- capacitor IC design steps down an input of 1:0 - 1:4 V to 0:6 V for a decade of load current from 5 - 50A

Polynomial Curve Slope Compensation for Peak-Current-Mode-Controlled Power Converters

Linear ramp slope compensation (LRC) and quadratic slope compensation (QSC) are commonly implemented in peak-current-mode-controlled dc-dc converters in order to minimize subharmonic and chaotic oscillations. Both compensating schemes rely on the linearized state-space averaged model (LSSA) of the converter. The LSSA ignores the impact that switching actions have on the stability of converters. In order to include switching events, the nonlinear analysis method based on the Monodromy matrix was introduced to describe a complete-cycle stability. Analyses on analog-controlled dc-dc converters applying this method show that system stability is strongly dependent on the change of the derivative of the slope at the time of switching instant. However, in a mixed-signal-controlled system, the digitalization effect contributes differently to system stability. This paper shows a full complete-cycle stability analysis using this nonlinear analysis method, which is applied to a mixed-signal-controlled converter. Through this analysis, a generalized equation is derived that reveals for the first time the real boundary stability limits for LRC and QSC. Furthermore, this generalized equation allows the design of a new compensating scheme, which is able to increase system stability. The proposed scheme is called polynomial curve slope compensation (PCSC) and it is demonstrated that PCSC increases the stable margin by 30% compared to LRC and 20% to QSC. This outcome is proved experimentally by using an interleaved dc-dc converter that is built for this work

A short predictive Model Predictive Control (MPC) approach for hybrid characteristics analysis in DC-DC converter

Historically, the MPC has been successfully applied in drives system for over a decade. Furthermore, the DC-DC converter naturally deals with high switching phenomenon that contributes to the challenging in control approach. Its operation conventionally associated with PI/PID controller in order to meet the desired output. However, the PI/PID controller lacking in getting a good transient response since this controller highly depends on the controller gains. Recently, an advanced controller has been proposed in the literature for the purpose to enhance the DC-DC converter performance. Hence, in this thesis, the short prediction horizon of MPC using search tree optimization that generates low switching states phenomenon is proposed. The MPC algorithm is developed based on the hybrid characteristic signals from the DC-DC converter. The load changes due to the increasing or decreasing the loads (could be happened of heating effect) will affect the tracking of the output voltage. The Kalman Filter (KF) is used for load estimation for smoothing and tracking the output voltage. The performance of short prediction horizons is being compared to PI controller in terms of transient response during the start-up scenario. The results show that the proposed controller has a better response than PI controller, which is the overshoot has been reduced to more than 50% and the settling time more faster about 25% than PI controller during start-up scenario. Therefore, this control approach for DC-DC buck converter has produced the promising output transient performance when compared with the conventional PI controller while also minimizing the switching sequence phenomenon

Analog/RF Circuit Design Techniques for Nanometerscale IC Technologies

CMOS evolution introduces several problems in analog design. Gate-leakage mismatch exceeds conventional matching tolerances requiring active cancellation techniques or alternative architectures. One strategy to deal with the use of lower supply voltages is to operate critical parts at higher supply voltages, by exploiting combinations of thin- and thick-oxide transistors. Alternatively, low voltage circuit techniques are successfully developed. In order to benefit from nanometer scale CMOS technology, more functionality is shifted to the digital domain, including parts of the RF circuits. At the same time, analog control for digital and digital control for analog emerges to deal with current and upcoming imperfections

Emulator of a boost converter for educational purposes

Project-based learning (PBL) is proposed for the development of a Hardware-in-the-Loop (HIL) platform and the design of its digital controller for an undergraduate course on Digital Electronic Systems. The objective for students is the design of a digitally controlled HIL Boost converter, a digital pulse-width modulator (DPWM) and a current mode controller, implemented in field-programmable gate array (FPGA) devices. To this end, the di erent parts of the project are developed and evaluated, maximizing the use of FPGA resources in the design of the HIL and DPWM blocks, and applying design techniques that minimize the use of the digital resources used in the design of the controller. Students are equipped with a new individualized educational experience, allowing them to test their technical competence and knowledge in an environment close to the reality of the industry