Vibration analysis of cable-driven parallel robots based on the dynamic stiffness matrix method

This paper focuses on the vibration analysis of Cable-Driven Parallel Robots (CDPRs). An oscillating model of CDPRs able to capture the dynamic behavior of the cables is derived using Lagrangian approach in conjunction with the Dynamic Stiffness Matrix method. Then, an original approach to analyze the modal interaction between the local cable modes and the global CDPR modes is presented. To illustrate this approach, numerical investigations and experimental analyses are carried out on a large-dimension 6-DOF suspended CDPR driven by 8 cables

Dynamic Control of a Novel Planar Cable-Driven Parallel Robot with a Large Wrench Feasible Workspace

Cable-Driven Parallel Robots (CDPRs) are special manipulators where rigid links are replaced with cables. The use of cables offers several advantages over the conventional rigid manipulators, one of the most interesting being their ability to cover large workspaces since cables are easily winded. However, this workspace coverage has its limitations due to the maximum permissible cable tensions, i.e., tension limitations cause a decrease in the Wrench Feasible Workspace (WFW) of these robots. To solve this issue, a novel design based in the addition of passive carriages to the robot frame of three degrees-of-freedom (3DOF) fully-constrained CDPRs is used. The novelty of the design allows reducing the variation in the cable directions and forces increasing the robot WFW; nevertheless, it presents a low stiffness along the x direction. This paper presents the dynamic model of the novel proposal together with a new dynamic control technique, which rejects the vibrations caused by the stiffness loss while ensuring an accurate trajectory tracking. The simulation results show that the controlled system presents a larger WFW than the conventional scheme of the CDPR, maintaining a good performance in the trajectory tracking of the end-effector. The novel proposal presented here can be applied in multiple planar applications

Modeling and Direct Adaptive Robust Control of Flexible Cable-Actuated Systems

Cable-actuated systems provide an effective method for precise motion transmission over various distances in many robotic systems. In general, the use of cables has many potential advantages such as high-speed manipulation, larger payloads, larger range of motion, access to remote locations and applications in hazardous environments. However, cable flexibility inevitably causes vibrations and poses a concern in high-bandwidth, high-precision applications

CABLE-SUSPENDED CPR-D TYPE PARALLEL ROBOT

This paper deals with the analysis and synthesis of a newly selected Cable-suspended Parallel Robot configuration, named CPR-D system. The camera carrier workspace has the shape of a parallelepiped. The CPR-D system has a unique Jacobian matrix that maps the relationship between internal and external coordinates. This geometric relationship is a key solution for the definition of the system kinematic and dynamic models. Because of the CPR-D system complexity, the Lagrange principle of virtual work has been adapted. Two significant Examples have been used for the CPR-D system analysis and validation

DESDEMONA Achievements

DESDEMONA achievements constitute a series of steps beyond the status of knowledge at the EU funded project starting on 1st June 2018, in the development of novel design methods, systems, procedure and technical solution, to integrate sensing and automation technologies for the purpose of self-inspection and self-monitoring of steel structures. The obtained results will lead to an increment of the service life of existing and new steel civil and industrial infrastructure and to a decrease in the cost associated to inspections, improving human activities performed in difficult conditions, safety and workers’ potential by the use of advanced tools. The research succeeded to expand new high-quality standard and practices for steel structure inspection and maintenance through the interrelated development of the following actions: i) steel structure geometry and condition virtualization through data fusion of image processing, thermography and vibration measurements; ii) developing of procedure for steel defect detection by robotic and automatic systems such as Cable-Driven Parallel Manipulators (CDPM), Unmanned Aerial Vehicles (UAV), Wall Climbing Drone (WCD), Cable Climbing Robot (CCR) and Wheeled Robot (WR) iii) embedding sensor systems to revalorize and transform steel elements and structures into self-diagnostic (smart) elements and materials even through nanotechnologies, iv) realizing an experimental lab-based apparatus and a series of case studies inspected by intelligent and robotic systems. The project outcomes are determining an impact on the reduction of the cost of steel structures inspection and maintenance and on the increase of user safety and comfort in industrial and civil environment

Reconfigurable cable driven parallel mechanism

Due to the fast growth in industry and in order to reduce manufacturing budget, increase the quality of products and increase the accuracy of manufactured products in addition to assure the safety of workers, people relied on mechanisms for such purposes. Recently, cable driven parallel mechanisms (CDPMs) have attracted much attention due to their many advantages over conventional parallel mechanisms, such as the significantly large workspace and the dynamics capacity. In addition, it has lower mass compared to other parallel mechanisms because of its negligible mass cables compared to the rigid links. In many applications it is required that human interact with machines and robots to achieve tasks precisely and accurately. Therefore, a new domain of scientific research has been introduced, that is human robot interaction, where operators can share the same workspace with robots and machines such as cable driven mechanisms. One of the main requirements due to this interaction that robots should respond to human actions in accurate, harmless way. In addition, the trajectory of the end effector is coming now from the operator and it is very essential that the initial trajectory is kept unchanged to perform tasks such assembly, operating or pick and place while avoiding the cables to interfere with each other or collide with the operator. Accordingly, many issues have been raised such as control, vibrations and stability due the contact between human and robot. Also, one of the most important issues is to guarantee collision free space (to avoid collision between cables and operator and to avoid collisions between cables itself). The aim of this research project is to model, design, analysis and implement reconfigurable six degrees of freedom parallel mechanism driven by eight cables. The main contribution of this work will be as follow. First, develop a nonlinear model and solve the forward and inverse kinematics issue of a fully constrained CDPM given that the attachment points on the rails are moving vertically (conventional cable driven mechanisms have fixed attachment points on the rails) while controlling the cable lengths. Second, the new idea of reconfiguration is then used to avoid interference between cables and between cables and operator limbs in real time by moving one cable’s attachment point on the frame to increase the shortest distance between them while keeping the trajectory of the end effector unchanged. Third, the new proposed approach was tested by creating a simulated intended cable-cable and cable-human interference trajectory, hence detecting and avoiding cable-cable and cable-human collision using the proposed real time reconfiguration while maintaining the initial end effector trajectory. Fourth, study the effect of relocating the attachment points on the constant-orientation wrench feasible workspace of the CDPM. En raison de la croissance de la demande de produits personnalisés et de la nécessité de réduire les coûts de fabrication tout en augmentant la qualité des produits et en augmentant la personnalisation des produits fabriqués en plus d'assurer la sécurité des travailleurs, les concepteurs se sont appuyés sur des mécanismes robotiques afin d’atteindre ces objectifs. Récemment, les mécanismes parallèles entraînés par câble (MPEC) ont attiré beaucoup d'attention en raison de leurs nombreux avantages par rapport aux mécanismes parallèles conventionnels, tels que l'espace de travail considérablement grand et la capacité dynamique. De plus, ce mécanisme a une masse plus faible par rapport à d'autres mécanismes parallèles en raison de ses câbles de masse négligeable comparativement aux liens rigides. Dans de nombreuses applications, il est nécessaire que l’humain interagisse avec les machines et les robots pour réaliser des tâches avec précision et rapidité. Par conséquent, un nouveau domaine de recherche scientifique a été introduit, à savoir l'interaction humain-robot, où les opérateurs peuvent partager le même espace de travail avec des robots et des machines telles que les mécanismes entraînés par des câbles. L'une des principales exigences en raison de cette interaction que les robots doivent répondre aux actions humaines d'une manière sécuritaire et collaboratif. En conséquence, de nombreux problèmes ont été soulevés tels que la commande et la stabilité dues au contact physique entre l’humain et le robot. Aussi, l'un des enjeux les plus importants est de garantir un espace sans collision (pour éviter les collisions entre des câbles et un opérateur et éviter les collisions entre les câbles entre eux). Le but de ce projet de recherche est de modéliser, concevoir, analyser et mettre en œuvre un mécanisme parallèle reconfigurable à six degrés de liberté entraîné par huit câbles. La principale contribution de ces travaux de recherche est de développer un modèle non linéaire et résolvez le problème de cinématique direct et inverse d'un CDPM entièrement contraint étant donné que les points d'attache sur les rails se déplacent verticalement (les mécanismes entraînés par des câbles conventionnels ont des points d'attache fixes sur les rails) tout en contrôlant les longueurs des câbles. Dans une deuxième étape, l’idée de la reconfiguration est ensuite utilisée pour éviter les interférences entre les câbles et entre les câbles et les membres d’un opérateur en temps réel en déplaçant un point de fixation du câble sur le cadre pour augmenter la distance la plus courte entre eux tout en gardant la trajectoire de l'effecteur terminal inchangée. Troisièmement, la nouvelle approche proposée a été évaluée et testée en créant une trajectoire d'interférence câble-câble et câble-humain simulée, détectant et évitant ainsi les collisions câble-câble et câble-humain en utilisant la reconfiguration en temps réel proposée tout en conservant la trajectoire effectrice finale. Enfin la dernière étape des travaux de recherche consiste à étudiez l'effet du déplacement des points d'attache sur l'espace de travail réalisable du CDPM

Hybrid Modeling of Deformable Linear Objects for Their Cooperative Transportation by Teams of Quadrotors

his paper deals with the control of a team of unmanned air vehicles (UAVs), specifically quadrotors, for which their mission is the transportation of a deformable linear object (DLO), i.e., a cable, hose or similar object in quasi-stationary state, while cruising towards destination. Such missions have strong industrial applications in the transportation of hoses or power cables to specific locations, such as the emergency power or water supply in hazard situations such as fires or earthquake damaged structures. This control must be robust to withstand strong and sudden wind disturbances and remain stable after aggressive maneuvers, i.e., sharp changes of direction or acceleration. To cope with these, we have previously developed the online adaptation of the proportional derivative (PD) controllers of the quadrotors thrusters, implemented by a fuzzy logic rule system that experienced adaptation by a stochastic gradient rule. However, sagging conditions appearing when the transporting drones are too close or too far away induce singularities in the DLO catenary models, breaking apart the control system. The paper’s main contribution is the formulation of the hybrid selective model of the DLO sections as either catenaries or parabolas, which allows us to overcome these sagging conditions. We provide the specific decision rule to shift between DLO models. Simulation results demonstrate the performance of the proposed approach under stringent conditions.This work has been partially supported by spanish MICIN project PID2020-116346GB-I00, and project KK-2021/00070 of the Elkartek 2021 funding program of the Basque Government. This project has received funding from the European Union’s Horizon 2020 research and innovation programme under the Marie Sklodowska-Curie grant agreement No. 777720

Vibrations of cable-suspended rehabilitation robots

Rehabilitation robots help the treatment of diseases by performing cyclic exercises for a long period of time. These exercises must perform movements of the patient's limbs; thus, the robots are required to be flexible and safe. Among rehabilitation robots, cable robots are widely used due to their unique properties, such as being lightweight and the possibility of being equipped with magnetic hooks to improve both safety and ease of use. However, the elasticity and flexibility of cables result in vibrations of the payload and hooks. In this paper, the forced vibrations due to rehabilitation exercises are studied. Since the previous studies of the authors showed a weak coupling between longitudinal and transverse vibrations, a two-cable planar model for the study of transverse vibrations is developed. The model makes it possible to study the forced transverse vibrations due to both cable motion and robot motion. Stiffness and damping of the patient's arm are considered. Results show that the cable system exhibits a simple linear behavior when excited by robot motion and a non-linear behavior when excited by cable motion