306 research outputs found
Low-Overhead Built-In Self-Test for Advanced RF Transceiver Architectures
abstract: Due to high level of integration in RF System on Chip (SOC), the test access points are limited to the baseband and RF inputs/outputs of the system. This limited access poses a big challenge particularly for advanced RF architectures where calibration of internal parameters is necessary and ensure proper operation. Therefore low-overhead built-in Self-Test (BIST) solution for advanced RF transceiver is proposed. In this dissertation. Firstly, comprehensive BIST solution for RF polar transceivers using on-chip resources is presented. In the receiver, phase and gain mismatches degrade sensitivity and error vector magnitude (EVM). In the transmitter, delay skew between the envelope and phase signals and the finite envelope bandwidth can create intermodulation distortion (IMD) that leads to violation of spectral mask requirements. Characterization and calibration of these parameters with analytical model would reduce the test time and cost considerably. Hence, a technique to measure and calibrate impairments of the polar transceiver in the loop-back mode is proposed.
Secondly, robust amplitude measurement technique for RF BIST application and BIST circuits for loop-back connection are discussed. Test techniques using analytical model are explained and BIST circuits are introduced.
Next, a self-compensating built-in self-test solution for RF Phased Array Mismatch is proposed. In the proposed method, a sinusoidal test signal with unknown amplitude is applied to the inputs of two adjacent phased array elements and measure the baseband output signal after down-conversion. Mathematical modeling of the circuit impairments and phased array behavior indicates that by using two distinct input amplitudes, both of which can remain unknown, it is possible to measure the important parameters of the phased array, such as gain and phase mismatch. In addition, proposed BIST system is designed and fabricated using IBM 180nm process and a prototype four-element phased-array PCB is also designed and fabricated for verifying the proposed method.
Finally, process independent gain measurement via BIST/DUT co-design is explained. Design methodology how to reduce performance impact significantly is discussed.
Simulation and hardware measurements results for the proposed techniques show that the proposed technique can characterize the targeted impairments accurately.Dissertation/ThesisDoctoral Dissertation Electrical Engineering 201
An Octave-Range, Watt-Level, Fully-Integrated CMOS Switching Power Mixer Array for Linearization and Back-Off-Efficiency Improvement
The power mixer array is presented as a novel power generation approach for non-constant envelope signals. It comprises several power mixer units that are dynamically turned on and off to improve the linearity and back-off efficiency. At the circuit level, the power mixer unit can operate as a switching amplifier to achieve high peak power efficiency. Additional circuit level linearization and back-off efficiency improvement techniques are also proposed. To demonstrate the feasibility of this idea, a fully-integrated octave-range CMOS power mixer array is implemented in a 130 nm CMOS process. It is operational between 1.2 GHz and 2.4 GHz and can generate an output power of +31.3 dBm into an external 50 Ω load with a PAE of 42% and a gain compression of only 0.4 dB at 1.8 GHz. It achieves a PAE of 25%, at an average output power of +26.4 dBm, and an EVM of 4.6% with a non-constant-envelope 16 QAM signal. It can also produce arbitrary signal levels down to -70 dBm of output power with the 16 QAM-modulated signal without any RF gain control circuit
Acoustical Ranging Techniques in Embedded Wireless Sensor Networked Devices
Location sensing provides endless opportunities for a wide range of applications in GPS-obstructed environments;
where, typically, there is a need for higher degree of accuracy. In this article, we focus on robust range
estimation, an important prerequisite for fine-grained localization. Motivated by the promise of acoustic in
delivering high ranging accuracy, we present the design, implementation and evaluation of acoustic (both
ultrasound and audible) ranging systems.We distill the limitations of acoustic ranging; and present efficient
signal designs and detection algorithms to overcome the challenges of coverage, range, accuracy/resolution,
tolerance to Doppler’s effect, and audible intensity. We evaluate our proposed techniques experimentally on
TWEET, a low-power platform purpose-built for acoustic ranging applications. Our experiments demonstrate
an operational range of 20 m (outdoor) and an average accuracy 2 cm in the ultrasound domain. Finally,
we present the design of an audible-range acoustic tracking service that encompasses the benefits of a near-inaudible
acoustic broadband chirp and approximately two times increase in Doppler tolerance to achieve better performance
A study of the minimum shift keying modulation scheme
This thesis concerns itself with the study of the Minimum Shift Keying (MSK) modulation scheme. The aspects considered are its operation under non-linear conditions as well as an investigation into the hardware implementation of both coherent and non-coherent MSK modems. The literature on digital data transmission and MSK in particular is surveyed, and a comprehensive theoretical description of MSK is given. In addition, papers on the operation of MSK under non-linear conditions were studied, and their major findings are presented. Due to the lack of theory on the effects of incorrect modulation index on the error performance of MSK, an investigation into this avenue was performed. The design of a correction mechanism for maintaining the modulation index at its correct value is described, and aspects of its implementation are considered. Using the available literature, various modules of which a coherent MSK modem is comprised were developed, and their design is discussed. The design of a non-coherent MSK demodulator is also described
Design and implementation of an Envelope tracking Power Amplifier using switched Amplifiers and slow Envelopes
English: This master thesis presents the design and implementation of an Envelope Tracking (ET) transmitter including an envelope amplifier based on switched power amplifiers and algorithms for slew-rate and bandwidth reduction. The ET transmitter here presented constitutes a research environment that will allow investigate possible solutions to solve the linearity-efficiency trade-off of the power amplifiers. The design and implementation of the envelope amplifier includes commercial switching devices driven by pulsed signals generated by a Field Programmable Gate Array (FPGA). The pulsed signals are modulated using Pulse Width Modulation and Delta-Sigma Modulation aimed to achieve a high efficient amplification. The signals, amplitudes, modulation frequencies and bandwidths used during the design and implementation are compatible with current communications standards. This master thesis also presents a new algorithm for reduction of the envelope bandwidth as well as improvements over the existing slew-rate reduction algorithm presented in a previous publication. These improvements were implemented in the FPGA and validated in the implemented transmitter. Results show that switching amplification is limited by the availability of current technologies in this field and the algorithms for reducing slew rate and bandwidth of the envelope are suitable to overcome this limitation while new technologies allow higher switching frequencies
Recommended from our members
Efficient, High power Precision RF and mmWave Digital Transmitter Architectures
Digital transmitters offer several advantages over conventional analog transmitters such as reconfigurability, elimination of scaling-unfriendly, power hungry and bulky analog blocks and portability across technology. The rapid advancement of technology in CMOS processes also enables integration of complex digital signal processing circuitry on the same die as the digital transmitter to compensate for their non-idealities. The use of this digital assistance can, for instance, enable the use of highly efficient but nonlinear switching-class power amplifiers by compensating for their severe nonlinearity through digital predistortion. While this shift to digitally intensive transmitter architectures is propelled by the benefits stated above, several pressing challenges arise that vary in their nature depending on the frequency of operation - from RF to mmWave.
Millimeter wave CMOS power amplifiers have traditionally been limited in output power due to the low breakdown voltage of scaled CMOS technologies and poor quality of on-chip passives. Moreover, high data-rates and efficient spectrum utilization demand highly linear power amplifiers with high efficiency under back-off. However, linearity and high efficiency are traditionally at odds with each other in conventional power amplifier design. In this dissertation, digital assistance is used to relax this trade-off and enable the use of state-of-the-art switching class power amplifiers. A novel digital transmitter architecture which simultaneously employs aggressive device-stacking and large-scale power combining for watt-class output power, dynamic load modulation for linearization, and improved efficiency under back-off by supply-switching and load modulation is presented.
At RF frequencies, while the problem of watt-class power amplification has been long solved, more pressing challenges arise from the crowded spectrum in this regime. A major drawback of digital transmitters is the absence of a reconstruction filter after digital-to-analog conversion which causes the baseband quantization noise to get upconverted to RF and amplified at the output of the transmitter. In high power transmitters, this upconverted noise can be so strong as to prevent their use in FDD systems due to receiver desensitization or impose stringent coexistence challenges. In this dissertation, new quantization noise suppression techniques are presented which, for the first time, contribute toward making watt-class fully-integrated digital RF transmitters a viable alternative for FDD and coexistence scenarios. Specifically, the techniques involve embedding a mixed-domain multi-tap FIR filter within highly-efficient watt-class switching power amplifiers to suppress quantization noise, enhancing the bandwidth of noise suppression, enabling tunable location of suppression and overcoming the limitations of purely digital-domain filtering techniques for quantization noise
Three Dimensional Bistatic Tomography Using HDTV
The thesis begins with a review of the principles of diffraction and reflection tomography; starting with the analytic solution to the inhomogeneous Helmholtz equation, after linearization by the Born approximation (the weak scatterer solution), and arriving at the Filtered Back Projection (Propagation) method of reconstruction. This is followed by a heuristic derivation more directly couched in the radar imaging context, without the rigor of the general inverse problem solution and more closely resembling an imaging turntable or inverse synthetic aperture radar. The heuristic derivation leads into the concept of the line integral and projections (the Radon Transform), followed by more general geometries where the plane wave approximation is invalid. We proceed next to study of the dependency of reconstruction on the space-frequency trajectory, combining the spatial aperture and waveform. Two and three dimensional apertures, monostatic and bistatic, fully and sparsely sampled and including partial apertures, with controlled waveforms (CW and pulsed, with and without modulation) define the filling of k-space and concomitant reconstruction performance. Theoretical developments in the first half of the thesis are applied to the specific example of bistatic tomographic imaging using High Definition Television (HDTV); the United States version of DVB-T. Modeling of the HDTV waveform using pseudonoise modulation to represent the hybrid 8VSB HDTV scheme and the move-stop-move approximation established the imaging potential, employing an idealized, isotropic 18 scatterer. As the move-stop-move approximation places a limitation on integration time (in cross correlation/pulse compression) due to transmitter/receiver motion, an exact solution for compensation of Doppler distortion is derived. The concept is tested with the assembly and flight test of a bistatic radar system employing software-defined radios (SDR). A three dimensional, bistatic collection aperture, exploiting an elevated commercial HDTV transmitter, is focused to demonstrate the principle. This work, to the best of our knowledge, represents a first in the formation of three dimensional images using bistatically-exploited television transmitters
- …