DFT and BIST of a multichip module for high-energy physics experiments

Engineers at Politecnico di Torino designed a multichip module for high-energy physics experiments conducted on the Large Hadron Collider. An array of these MCMs handles multichannel data acquisition and signal processing. Testing the MCM from board to die level required a combination of DFT strategie

Identifying worst case test vectors for FPGA exposed to total ionization dose using design for testability techniques

Electronic devices often operate in harsh environments which contain a variation of radiation sources. Radiation may cause different kinds of damage to proper operation of the devices. Their sources can be found in terrestrial environments, or in extra-terrestrial environments like in space, or in man-made radiation sources like nuclear reactors, biomedical devices and high energy particles physics experiments equipment. Depending on the operation environment of the device, the radiation resultant effect manifests in several forms like total ionizing dose effect (TID), or single event effects (SEEs) such as single event upset (SEU), single event gate rupture (SEGR), and single event latch up (SEL). TID effect causes an increase in the delay and the leakage current of CMOS circuits which may damage the proper operation of the integrated circuit. To ensure proper operation of these devices under radiation, thorough testing must be made especially in critical applications like space and military applications. Although the standard which describes the procedure for testing electronic devices under radiation emphasizes the use of worst case test vectors (WCTVs), they are never used in radiation testing due to the difficulty of generating these vectors for circuits under test. For decades, design for testability (DFT) has been the best choice for test engineers to test digital circuits in industry. It has become a very mature technology that can be relied on. DFT is usually used with automatic test patterns generation (ATPG) software to generate test vectors to test application specific integrated circuits (ASICs), especially with sequential circuits, against faults like stuck at faults and path delay faults. Surprisingly, however, radiation testing has not yet made use of this reliable technology. In this thesis, a novel methodology is proposed to extend the usage of DFT to generate WCTVs for delay failure in Flash based field programmable gate arrays (FPGAs) exposed to total ionizing dose (TID). The methodology is validated using MicroSemi ProASIC3 FPGA and cobalt 60 facility

A comprehensive comparison between design for testability techniques for total dose testing of flash-based FPGAs

Radiation sources exist in different kinds of environments where electronic devices often operate. Correct device operation is usually affected negatively by radiation. The radiation resultant effect manifests in several forms depending on the operating environment of the device like total ionizing dose effect (TID), or single event effects (SEEs) such as single event upset (SEU), single event gate rupture (SEGR), and single event latch up (SEL). CMOS circuits and Floating gate MOS circuits suffer from an increase in the delay and the leakage current due to TID effect. This may damage the proper operation of the integrated circuit. Exhaustive testing is needed for devices operating in harsh conditions like space and military applications to ensure correct operations in the worst circumstances. The use of worst case test vectors (WCTVs) for testing is strongly recommended by MIL-STD-883, method 1019, which is the standard describing the procedure for testing electronic devices under radiation. However, the difficulty of generating these test vectors hinders their use in radiation testing. Testing digital circuits in the industry is usually done nowadays using design for testability (DFT) techniques as they are very mature and can be relied on. DFT techniques include, but not limited to, ad-hoc technique, built-in self test (BIST), muxed D scan, clocked scan and enhanced scan. DFT is usually used with automatic test patterns generation (ATPG) software to generate test vectors to test application specific integrated circuits (ASICs), especially with sequential circuits, against faults like stuck at faults and path delay faults. Despite all these recommendations for DFT, radiation testing has not benefited from this reliable technology yet. Also, with the big variation in the DFT techniques, choosing the right technique is the bottleneck to achieve the best results for TID testing. In this thesis, a comprehensive comparison between different DFT techniques for TID testing of flash-based FPGAs is made to help designers choose the best suitable DFT technique depending on their application. The comparison includes muxed D scan technique, clocked scan technique and enhanced scan technique. The comparison is done using ISCAS-89 benchmarks circuits. Points of comparisons include FPGA resources utilization, difficulty of designs bring-up, added delay by DFT logic and robust testable paths in each technique

REDUCING POWER DURING MANUFACTURING TEST USING DIFFERENT ARCHITECTURES

Power during manufacturing test can be several times higher than power consumption in functional mode. Excessive power during test can cause IR drop, over-heating, and early aging of the chips. In this dissertation, three different architectures have been introduced to reduce test power in general cases as well as in certain scenarios, including field test. In the first architecture, scan chains are divided into several segments. Every segment needs a control bit to enable capture in a segment when new faults are detectable on that segment for that pattern. Otherwise, the segment should be disabled to reduce capture power. We group the control bits together into one or more control chains. To address the extra pin(s) required to shift data into the control chain(s) and significant post processing in the first architecture, we explored a second architecture. The second architecture stitches the control bits into the chains they control as EECBs (embedded enable capture bits) in between the segments. This allows an ATPG software tool to automatically generate the appropriate EECB values for each pattern to maintain the fault coverage. This also works in the presence of an on-chip decompressor. The last architecture focuses primarily on the self-test of a device in a 3D stacked IC when an existing FPGA in the stack can be programmed as a tester. We show that the energy expended during test is significantly less than would be required using low power patterns fed by an on-chip decompressor for the same very short scan chains

Analysis and application of digital spectral warping in analog and mixed-signal testing

Spectral warping is a digital signal processing transform which shifts the frequencies contained within a signal along the frequency axis. The Fourier transform coefficients of a warped signal correspond to frequency-domain 'samples' of the original signal which are unevenly spaced along the frequency axis. This property allows the technique to be efficiently used for DSP-based analog and mixed-signal testing. The analysis and application of spectral warping for test signal generation, response analysis, filter design, frequency response evaluation, etc. are discussed in this paper along with examples of the software and hardware implementation

A Flexible Power Control Method for Right Power Testing of Scan-Based Logic BIST

High power dissipation during scan-based logic BIST is a crucial problem that leads to over-testing. Although controlling test power of a circuit under test (CUT) to an appropriate level is strongly required, it is not easy to control test power in BIST. This paper proposes a novel power controlling method to control the toggle rate of the patterns to an arbitrary level by modifying pseudo random patterns generated by a TPG (Test Pattern Generator) of logic BIST. While many approaches have been proposed to control the toggle rate of the patterns, the proposed approach can provide higher fault coverage. Experimental results show that the proposed approach can control toggle rates to a predetermined target level and modified patterns can achieve high fault coverage without increasing test time.2016 IEEE 25th Asian Test Symposium (ATS), 21-24 Nov. 2016, Hiroshima, Japa

Built-In Self-Test (BIST) for Multi-Threshold NULL Convention Logic (MTNCL) Circuits

This dissertation proposes a Built-In Self-Test (BIST) hardware implementation for Multi-Threshold NULL Convention Logic (MTNCL) circuits. Two different methods are proposed: an area-optimized topology that requires minimal area overhead, and a test-performance-optimized topology that utilizes parallelism and internal hardware to reduce the overall test time through additional controllability points. Furthermore, an automated software flow is proposed to insert, simulate, and analyze an input MTNCL netlist to obtain a desired fault coverage, if possible, through iterative digital and fault simulations. The proposed automated flow is capable of producing both area-optimized and test-performance-optimized BIST circuits and scripts for digital and fault simulation using commercial software that may be utilized to manually verify or adjust further, if desired

Testing of leakage current failure in ASIC devices exposed to total ionizing dose environment using design for testability techniques

Due to the advancements in technology, electronic devices have been relied upon to operate under harsh conditions. Radiation is one of the main causes of different failures of the electronics devices. According to the operation environment, the sources of the radiation can be terrestrial or extra-terrestrial. For terrestrial the devices can be used in nuclear reactors or biomedical devices where the radiation is man-made. While for the extra- terrestrial, the devices can be used in satellites, the international space station or spaceships, where the radiation comes from various sources like the Sun. According to the operation environment the effects of radiation differ. These effects falls under two categories, total ionizing dose effect (TID) and single event effects (SEEs). TID effects can be affect the delay and leakage current of CMOS circuits negatively. The affects can therefore hinder the integrated circuits\u27 operation. Before the circuits are used, particularly in critical radiation heavy applications like military and space, testing under radiation must be done to avoid any failures during operation. The standard in testing electronic devices is generating worst case test vectors (WCTVs) and under radiation using these vectors the circuits are tested. However, the generation of these WCTVs have been very challenging so this approach is rarely used for TIDs effects. Design for testability (DFT) have been widely used in the industry for digital circuits testing applications. DFT is usually used with automatic test patterns generation software to generate test vectors against fault models of manufacturer defects for application specific integrated circuit (ASIC.) However, it was never used to generate test vectors for leakage current testing induced in ASICs exposed to TID radiation environment. The purpose of the thesis is to use DFT to identify WCTVs for leakage current failures in sequential circuits for ASIC devices exposed to TID. A novel methodology was devised to identify these test vectors. The methodology is validated and compared to previous non DFT methods. The methodology is proven to overcome the limitation of previous methodologies