Robust Fault Detection of Switched Linear Systems with State Delays

This correspondence deals with the problem of robust fault detection for discrete-time switched systems with state delays under an arbitrary switching signal. The fault detection filter is used as the residual generator, in which the filter parameters are dependent on the system mode. Attention is focused on designing the robust fault detection filter such that, for unknown inputs, control inputs, and model uncertainties, the estimation error between the residuals and faults is minimized. The problem of robust fault detection is converted into an H infin-filtering problem. By a switched Lyapunov functional approach, a sufficient condition for the solvability of this problem is established in terms of linear matrix inequalities. A numerical example is provided to demonstrate the effectiveness of the proposed method

A review of convex approaches for control, observation and safety of linear parameter varying and Takagi-Sugeno systems

This paper provides a review about the concept of convex systems based on Takagi-Sugeno, linear parameter varying (LPV) and quasi-LPV modeling. These paradigms are capable of hiding the nonlinearities by means of an equivalent description which uses a set of linear models interpolated by appropriately defined weighing functions. Convex systems have become very popular since they allow applying extended linear techniques based on linear matrix inequalities (LMIs) to complex nonlinear systems. This survey aims at providing the reader with a significant overview of the existing LMI-based techniques for convex systems in the fields of control, observation and safety. Firstly, a detailed review of stability, feedback, tracking and model predictive control (MPC) convex controllers is considered. Secondly, the problem of state estimation is addressed through the design of proportional, proportional-integral, unknown input and descriptor observers. Finally, safety of convex systems is discussed by describing popular techniques for fault diagnosis and fault tolerant control (FTC).Peer ReviewedPostprint (published version

Fault detection and isolation for linear dynamic systems

As modern control systems and engineering processes become increasingly more complex and integrated, the consequences of system failures and faults can be disastrous environmentally and economically. This thesis considers the fault detection and isolation (FDI) problem for linear time-invariant (LTI) systems subject to faults, disturbances and model uncertainties. Firstly, a novel on-line approach to the robust FDI problem for linear discrete-time systems is proposed by using input/output measurement analysis over a finite estimation horizon. Upper and lower bounds on the fault signal are computed at each sampling instant so that a fault is detected and isolated when its upper bound is smaller than zero or its lower bound is larger than zero. Moreover, a subsequent-state-estimation technique, together with an estimation horizon update procedure are given to allow the on-line FDI process to be repeated in a moving horizon scheme. Secondly, an optimal solution to theH−/H∞ fault detection (FD) problem is given for linear time-invariant systems subject to faults, disturbances and model uncertainties by using an observer-based approach. A new performance index is developed to capture both fault detection and disturbance rejection requirements which is particularly suitable for handling model uncertainties. A class of optimal solutions to the problem is then given in the form of simple linear matrix inequalities (LMI) with two degrees of freedom. By appropriately choosing these degrees of freedom, fault isolation can also be achieved. Thirdly, in order to improve the FD performance and remove restrictive rank assumptions, routinely made in the literature, observer-based FD problems are investigated at a single frequency and over a finite frequency range, respectively. An optimal solution is derived such that, at a given frequency, the static observer generates a residual signal which minimizes the sensitivity of the residual to disturbances while maintaining a minimum level of sensitivity to faults. Then, an initial investigation is carried out for the FD problem over a finite frequency range. A solution is derived in the form of an LMI optimization by using the generalized KYP lemma followed by a linearization procedure. Conditions under which this solution is optimal are also derived. Fully worked out numerical examples, mostly from the literature, are given to illustrate the effectiveness of all the proposed schemes

Fault estimation and active fault tolerant control for linear parameter varying descriptor systems

Starting with the baseline controller design, this paper proposes an integrated approach of active fault tolerant control based on proportional derivative extended state observer (PDESO) for linear parameter varying descriptor systems. The PDESO can simultaneously provide the estimates of the system states, sensor faults, and actuator faults. The L₂ robust performance of the closed-loop system to bounded exogenous disturbance and bounded uncertainty is achieved by a two-step design procedure adapted from the traditional observer-based controller design. Furthermore, an LMI pole-placement region and the L₂ robustness performance are combined into a multiobjective formulation by suitably combing the appropriate LMI descriptions. A parameter-varying system example is given to illustrate the design procedure and the validity of the proposed integrated design approach

Fault detection and isolation filter design for systems subject to polytopic uncertainties

This paper considers the robust fault detection and isolation (FDI) problem for linear time-invariant dynamic systems subject to faults, disturbances and polytopic uncertainties. We employ an observer-based FDI filter to generate a residual signal. We propose a cost function that penalizes a weighted combination of the deviation of the fault to residual dynamics from a given fault isolation reference model, as well as the effects of disturbances and uncertainties on the residual, using the Hinfin norm as a measure. The proposed cost function thus captures the requirements of fault detection and isolation and disturbance rejection in the presence of polytopic uncertainties. We derive necessary and sufficient conditions for the existence of an FDI filter that achieves the design specifications. This condition takes the form of easily implementable linear matrix inequality (LMI) optimization problem

On design of quantized fault detection filters with randomly occurring nonlinearities and mixed time-delays

This paper is concerned with the fault detection problem for a class of discrete-time systems with randomly occurring nonlinearities, mixed stochastic time-delays as well as measurement quantizations. The nonlinearities are assumed to occur in a random way. The mixed time-delays comprise both the multiple discrete time-delays and the infinite distributed delays that occur in a random way as well. A sequence of stochastic variables is introduced to govern the random occurrences of the nonlinearities, discrete time-delays and distributed time-delays, where all the stochastic variables are mutually independent but obey the Bernoulli distribution. The main purpose of this paper is to design a fault detection filter such that, in the presence of measurement quantization, the overall fault detection dynamics is exponentially stable in the mean square and, at the same time, the error between the residual signal and the fault signal is made as small as possible. Sufficient conditions are first established via intensive stochastic analysis for the existence of the desired fault detection filters, and then the explicit expression of the desired filter gains is derived by means of the feasibility of certain matrix inequalities. Also, the optimal performance index for the addressed fault detection problem can be obtained by solving an auxiliary convex optimization problem. A practical example is provided to show the usefulness and effectiveness of the proposed design method