Synchronization for capacity -approaching coded communication systems

The dissertation concentrates on synchronization of capacity approaching error-correction codes that are deployed in noisy channels with very low signal-to-noise ratio (SNR). The major topics are symbol timing synchronization and frame synchronization.;Capacity-approaching error-correction codes, like turbo codes and low-density parity-check (LDPC) codes, are capable of reaching very low bit error rates and frame error rates in noisy channels by iterative decoding. To fully achieve the potential decoding capability of Turbo codes and LDPC codes, proper symbol timing synchronization, frame synchronization and channel state estimation are required. The dissertation proposes a joint estimator of symbol time delay and channel SNR for symbol timing recovery, and a maximum a posteriori (MAP) frame synchronizer for frame synchronization.;Symbol timing recovery is implemented by sampling and interpolation. The received signal is sampled multiple times per symbol period with unknown delay and unknown SNR. A joint estimator estimates the time delay and the SNR. The signal is rebuilt by interpolating available samples using estimated time delay. The intermediate decoding results enable decision-feedback estimation. The estimates of time delay and SNR are refined by iterative processing. This refinement improves the system performance significantly.;Usually the sampling rate is assumed to be a strict integer multiple of the symbol rate. However, in a practical system the local oscillators in the transmitter and the receiver may have random drifts. Therefore the sampling rate is no longer an exact multiple of the symbol rate, and the sampling time follows a random walk. This random walk may harm the system performance severely. The dissertation analyzes the effect of random time walks and proposes to mitigate the effect by overlapped sliding windows and iterative processing.;Frame synchronization is required to find the correct boundaries of codewords. MAP frame synchronization in the sense of minimizing the frame sync failure rate is investigated. The MAP frame synchronizer explores low-density parity-check attributes of the capacity-approaching codes. The accuracy of frame synchronization is adequate for considered coded systems to work reliably under very low SNR

Design tradeoffs and challenges in practical coherent optical transceiver implementations

This tutorial discusses the design and ASIC implementation of coherent optical transceivers. Algorithmic and architectural options and tradeoffs between performance and complexity/power dissipation are presented. Particular emphasis is placed on flexible (or reconfigurable) transceivers because of their importance as building blocks of software-defined optical networks. The paper elaborates on some advanced digital signal processing (DSP) techniques such as iterative decoding, which are likely to be applied in future coherent transceivers based on higher order modulations. Complexity and performance of critical DSP blocks such as the forward error correction decoder and the frequency-domain bulk chromatic dispersion equalizer are analyzed in detail. Other important ASIC implementation aspects including physical design, signal and power integrity, and design for testability, are also discussed.Fil: Morero, Damián Alfonso. Universidad Nacional de Córdoba. Facultad de Ciencias Exactas, Físicas y Naturales; Argentina. ClariPhy Argentina S.A.; ArgentinaFil: Castrillon, Alejandro. Universidad Nacional de Córdoba. Facultad de Ciencias Exactas, Físicas y Naturales; ArgentinaFil: Aguirre, Alejandro. ClariPhy Argentina S.A.; ArgentinaFil: Hueda, Mario Rafael. Consejo Nacional de Investigaciones Científicas y Técnicas. Centro Científico Tecnológico Conicet - Córdoba. Instituto de Estudios Avanzados en Ingeniería y Tecnología. Universidad Nacional de Córdoba. Facultad de Ciencias Exactas Físicas y Naturales. Instituto de Estudios Avanzados en Ingeniería y Tecnología; ArgentinaFil: Agazzi, Oscar Ernesto. Universidad Nacional de Córdoba. Facultad de Ciencias Exactas, Físicas y Naturales; Argentina. ClariPhy Argentina S.A.; Argentin

Non-iterative joint decoding and signal processing: universal coding approach for channels with memory

A non-iterative receiver is proposed to achieve near capacity performance on intersymbol interference (ISI) channels. There are two main ingredients in the proposed design. i) The use of a novel BCJR-DFE equalizer which produces optimal soft estimates of the inputs to the ISI channel given all the observations from the channel and L past symbols exactly, where L is the memory of the ISI channel. ii) The use of an encoder structure that ensures that L past symbols can be used in the DFE in an error free manner through the use of a capacity achieving code for a memoryless channel. Computational complexity of the proposed receiver structure is less than that of one iteration of the turbo receiver. We also provide the proof showing that the proposed receiver achieves the i.i.d. capacity of any constrained input ISI channel. This DFE-based receiver has several advantages over an iterative (turbo) receiver, such as low complexity, the fact that codes that are optimized for memoryless channels can be used with channels with memory, and finally that the channel does not need to be known at the transmitter. The proposed coding scheme is universal in the sense that a single code of rate r; optimized for a memoryless channel, provides small error probability uniformly across all AWGN-ISI channels of i.i.d. capacity less than r: This general principle of a proposed non-iterative receiver also applies to other signal processing functions, such as timing recovery, pattern-dependent noise whiten ing, joint demodulation and decoding etc. This makes the proposed encoder and receiver structure a viable alternative to iterative signal processing. The results show significant complexity reduction and performance gain for the case of timing recovery and patter-dependent noise whitening for magnetic recording channels

On Coding and Detection Techniques for Two-Dimensional Magnetic Recording

Edited version embargoed until 15.04.2020 Full version: Access restricted permanently due to 3rd party copyright restrictions. Restriction set on 15/04/2019 by AS, Doctoral CollegeThe areal density growth of magnetic recording systems is fast approaching the superparamagnetic limit for conventional magnetic disks. This is due to the increasing demand for high data storage capacity. Two-dimensional Magnetic Recording (TDMR) is a new technology aimed at increasing the areal density of magnetic recording systems beyond the limit of current disk technology using conventional disk media. However, it relies on advanced coding and signal processing techniques to achieve areal density gains. Current state of the art signal processing for TDMR channel employed iterative decoding with Low Density Parity Check (LDPC) codes, coupled with 2D equalisers and full 2D Maximum Likelihood (ML) detectors. The shortcoming of these algorithms is their computation complexity especially with regards to the ML detectors which is exponential with respect to the number of bits involved. Therefore, robust low-complexity coding, equalisation and detection algorithms are crucial for successful future deployment of the TDMR scheme. This present work is aimed at finding efficient and low-complexity coding, equalisation, detection and decoding techniques for improving the performance of TDMR channel and magnetic recording channel in general. A forward error correction (FEC) scheme of two concatenated single parity bit systems along track separated by an interleaver has been presented for channel with perpendicular magnetic recording (PMR) media. Joint detection decoding algorithm using constrained MAP detector for simultaneous detection and decoding of data with single parity bit system has been proposed. It is shown that using the proposed FEC scheme with the constrained MAP detector/decoder can achieve a gain of up to 3dB over un-coded MAP decoder for 1D interference channel. A further gain of 1.5 dB was achieved by concatenating two interleavers with extra parity bit when data density along track is high. The use of single bit parity code as a run length limited code as well as an error correction code is demonstrated to simplify detection complexity and improve system performance. A low-complexity 2D detection technique for TDMR system with Shingled Magnetic Recording Media (SMR) was also proposed. The technique used the concatenation of 2D MAP detector along track with regular MAP detector across tracks to reduce the complexity order of using full 2D detection from exponential to linear. It is shown that using this technique can improve track density with limited complexity. Two methods of FEC for TDMR channel using two single parity bit systems have been discussed. One using two concatenated single parity bits along track only, separated by a Dithered Relative Prime (DRP) interleaver and the other use the single parity bits in both directions without the DRP interleaver. Consequent to the FEC coding on the channel, a 2D multi-track MAP joint detector decoder has been proposed for simultaneous detection and decoding of the coded single parity bit data. A gain of up to 5dB was achieved using the FEC scheme with the 2D multi-track MAP joint detector decoder over un-coded 2D multi-track MAP detector in TDMR channel. In a situation with high density in both directions, it is shown that FEC coding using two concatenated single parity bits along track separated by DRP interleaver performed better than when the single parity bits are used in both directions without the DRP interleaver.9mobile Nigeri

Capacity -based parameter optimization of bandwidth constrained CPM

Continuous phase modulation (CPM) is an attractive modulation choice for bandwidth limited systems due to its small side lobes, fast spectral decay and the ability to be noncoherently detected. Furthermore, the constant envelope property of CPM permits highly power efficient amplification. The design of bit-interleaved coded continuous phase modulation is characterized by the code rate, modulation order, modulation index, and pulse shape. This dissertation outlines a methodology for determining the optimal values of these parameters under bandwidth and receiver complexity constraints. The cost function used to drive the optimization is the information-theoretic minimum ratio of energy-per-bit to noise-spectral density found by evaluating the constrained channel capacity. The capacity can be reliably estimated using Monte Carlo integration. A search for optimal parameters is conducted over a range of coded CPM parameters, bandwidth efficiencies, and channels. Results are presented for a system employing a trellis-based coherent detector. To constrain complexity and allow any modulation index to be considered, a soft output differential phase detector has also been developed.;Building upon the capacity results, extrinsic information transfer (EXIT) charts are used to analyze a system that iterates between demodulation and decoding. Convergence thresholds are determined for the iterative system for different outer convolutional codes, alphabet sizes, modulation indices and constellation mappings. These are used to identify the code and modulation parameters with the best energy efficiency at different spectral efficiencies for the AWGN channel. Finally, bit error rate curves are presented to corroborate the capacity and EXIT chart designs

Architecture and algorithms for the implementation of digital wireless receivers in FPGA and ASIC: ISDB-T and DVB-S2 cases

[EN] The first generation of Terrestrial Digital Television(DTV) has been in service for over a decade. In 2013, several countries have already completed the transition from Analog to Digital TV Broadcasting, most of which in Europe. In South America, after several studies and trials, Brazil adopted the Japanese standard with some innovations. Japan and Brazil started Digital Terrestrial Television Broadcasting (DTTB) services in December 2003 and December 2007 respectively, using Integrated Services Digital Broadcasting - Terrestrial (ISDB-T), also known as ARIB STD-B31. In June 2005 the Committee for the Information Technology Area (CATI) of Brazilian Ministry of Science and Technology and Innovation MCTI approved the incorporation of the IC-Brazil Program, in the National Program for Microelectronics (PNM) . The main goals of IC-Brazil are the formal qualification of IC designers, support to the creation of semiconductors companies focused on projects of ICs within Brazil, and the attraction of semiconductors companies focused on the design and development of ICs in Brazil. The work presented in this thesis originated from the unique momentum created by the combination of the birth of Digital Television in Brazil and the creation of the IC-Brazil Program by the Brazilian government. Without this combination it would not have been possible to make these kind of projects in Brazil. These projects have been a long and costly journey, albeit scientifically and technologically worthy, towards a Brazilian DTV state-of-the-art low complexity Integrated Circuit, with good economy scale perspectives, due to the fact that at the beginning of this project ISDB-T standard was not adopted by several countries like DVB-T. During the development of the ISDB-T receiver proposed in this thesis, it was realized that due to the continental dimensions of Brazil, the DTTB would not be enough to cover the entire country with open DTV signal, specially for the case of remote localizations far from the high urban density regions. Then, Eldorado Research Institute and Idea! Electronic Systems, foresaw that, in a near future, there would be an open distribution system for high definition DTV over satellite, in Brazil. Based on that, it was decided by Eldorado Research Institute, that would be necessary to create a new ASIC for broadcast satellite reception. At that time DVB-S2 standard was the strongest candidate for that, and this assumption still stands nowadays. Therefore, it was decided to apply to a new round of resources funding from the MCTI - that was granted - in order to start the new project. This thesis discusses in details the Architecture and Algorithms proposed for the implementation of a low complexity Intermediate Frequency(IF) ISDB-T Receiver on Application Specific Integrated Circuit (ASIC) CMOS. The Architecture proposed here is highly based on the COordinate Rotation Digital Computer (CORDIC) Algorithm, that is a simple and efficient algorithm suitable for VLSI implementations. The receiver copes with the impairments inherent to wireless channels transmission and the receiver crystals. The thesis also discusses the Methodology adopted and presents the implementation results. The receiver performance is presented and compared to those obtained by means of simulations. Furthermore, the thesis also presents the Architecture and Algorithms for a DVB-S2 receiver targeting its ASIC implementation. However, unlike the ISDB-T receiver, only preliminary ASIC implementation results are introduced. This was mainly done in order to have an early estimation of die area to prove that the project in ASIC is economically viable, as well as to verify possible bugs in early stage. As in the case of ISDB-T receiver, this receiver is highly based on CORDIC algorithm and it was prototyped in FPGA. The Methodology used for the second receiver is derived from that used for the ISDB-T receiver, with minor additions given the project characteristics.[ES] La primera generación de Televisión Digital Terrestre(DTV) ha estado en servicio por más de una década. En 2013, varios países completaron la transición de transmisión analógica a televisión digital, la mayoría de ellas en Europa. En América del Sur, después de varios estudios y ensayos, Brasil adoptó el estándar japonés con algunas innovaciones. Japón y Brasil comenzaron a prestar el servicio de Difusión de Televisión Digital Terrestre (DTTB) en diciembre de 2003 y diciembre de 2007 respectivamente, utilizando Radiodifusión Digital de Servicios Integrados Terrestres (ISDB-T), también conocida como ARIB STD-B31. En junio de 2005, el Comité del Área de Tecnología de la Información (CATI) del Ministerio de Ciencia, Tecnología e Innovación de Brasil - MCTI aprobó la incorporación del Programa CI-Brasil, en el Programa Nacional de Microelectrónica (PNM). Los principales objetivos de la CI-Brasil son la formación de diseñadores de CIs, apoyar la creación de empresas de semiconductores enfocadas en proyectos de circuitos integrados dentro de Brasil, y la atracción de empresas de semiconductores interesadas en el diseño y desarrollo de circuitos integrados. El trabajo presentado en esta tesis se originó en el impulso único creado por la combinación del nacimiento de la televisión digital en Brasil y la creación del Programa de CI-Brasil por el gobierno brasileño. Sin esta combinación no hubiera sido posible realizar este tipo de proyectos en Brasil. Estos proyectos han sido un trayecto largo y costoso, aunque meritorio desde el punto de vista científico y tecnológico, hacia un Circuito Integrado brasileño de punta y de baja complejidad para DTV, con buenas perspectivas de economía de escala debido al hecho que al inicio de este proyecto, el estándar ISDB-T no fue adoptado por varios países como DVB-T. Durante el desarrollo del receptor ISDB-T propuesto en esta tesis, se observó que debido a las dimensiones continentales de Brasil, la DTTB no sería suficiente para cubrir todo el país con la señal de televisión digital abierta, especialmente para el caso de localizaciones remotas, apartadas de las regiones de alta densidad urbana. En ese momento, el Instituto de Investigación Eldorado e Idea! Sistemas Electrónicos, previeron que en un futuro cercano habría un sistema de distribución abierto para DTV de alta definición por satélite en Brasil. Con base en eso, el Instituto de Investigación Eldorado decidió que sería necesario crear un nuevo ASIC para la recepción de radiodifusión por satélite, basada el estándar DVB-S2. En esta tesis se analiza en detalle la Arquitectura y algoritmos propuestos para la implementación de un receptor ISDB-T de baja complejidad y frecuencia intermedia (IF) en un Circuito Integrado de Aplicación Específica (ASIC) CMOS. La arquitectura aquí propuesta se basa fuertemente en el algoritmo Computadora Digital para Rotación de Coordenadas (CORDIC), el cual es un algoritmo simple, eficiente y adecuado para implementaciones VLSI. El receptor hace frente a las deficiencias inherentes a las transmisiones por canales inalámbricos y los cristales del receptor. La tesis también analiza la metodología adoptada y presenta los resultados de la implementación. Por otro lado, la tesis también presenta la arquitectura y los algoritmos para un receptor DVB-S2 dirigido a la implementación en ASIC. Sin embargo, a diferencia del receptor ISDB-T, se introducen sólo los resultados preliminares de implementación en ASIC. Esto se hizo principalmente con el fin de tener una estimación temprana del área del die para demostrar que el proyecto en ASIC es económicamente viable, así como para verificar posibles errores en etapa temprana. Como en el caso de receptor ISDB-T, este receptor se basa fuertemente en el algoritmo CORDIC y fue un prototipado en FPGA. La metodología utilizada para el segundo receptor se deriva de la utilizada para el re[CA] La primera generació de Televisió Digital Terrestre (TDT) ha estat en servici durant més d'una dècada. En 2013, diversos països ja van completar la transició de la radiodifusió de televisió analògica a la digital, i la majoria van ser a Europa. A Amèrica del Sud, després de diversos estudis i assajos, Brasil va adoptar l'estàndard japonés amb algunes innovacions. Japó i Brasil van començar els servicis de Radiodifusió de Televisió Terrestre Digital (DTTB) al desembre de 2003 i al desembre de 2007, respectivament, utilitzant la Radiodifusió Digital amb Servicis Integrats de (ISDB-T), coneguda com a ARIB STD-B31. Al juny de 2005, el Comité de l'Àrea de Tecnologia de la Informació (CATI) del Ministeri de Ciència i Tecnologia i Innovació del Brasil (MCTI) va aprovar la incorporació del programa CI Brasil al Programa Nacional de Microelectrònica (PNM). Els principals objectius de CI Brasil són la qualificació formal dels dissenyadors de circuits integrats, el suport a la creació d'empreses de semiconductors centrades en projectes de circuits integrats dins del Brasil i l'atracció d'empreses de semiconductors centrades en el disseny i desenvolupament de circuits integrats. El treball presentat en esta tesi es va originar en l'impuls únic creat per la combinació del naixement de la televisió digital al Brasil i la creació del programa Brasil CI pel govern brasiler. Sense esta combinació no hauria estat possible realitzar este tipus de projectes a Brasil. Estos projectes han suposat un viatge llarg i costós, tot i que digne científicament i tecnològica, cap a un circuit integrat punter de baixa complexitat per a la TDT brasilera, amb bones perspectives d'economia d'escala perquè a l'inici d'este projecte l'estàndard ISDB-T no va ser adoptat per diversos països, com el DVB-T. Durant el desenvolupament del receptor de ISDB-T proposat en esta tesi, va resultar que, a causa de les dimensions continentals de Brasil, la DTTB no seria suficient per cobrir tot el país amb el senyal de TDT oberta, especialment pel que fa a les localitzacions remotes allunyades de les regions d'alta densitat urbana.. En este moment, l'Institut de Recerca Eldorado i Idea! Sistemes Electrònics van preveure que, en un futur pròxim, no hi hauria a Brasil un sistema de distribució oberta de TDT d'alta definició a través de satèl¿lit. D'acord amb això, l'Institut de Recerca Eldorado va decidir que seria necessari crear un nou ASIC per a la recepció de radiodifusió per satèl¿lit. basat en l'estàndard DVB-S2. En esta tesi s'analitza en detall l'arquitectura i els algorismes proposats per l'execució d'un receptor ISDB-T de Freqüència Intermèdia (FI) de baixa complexitat sobre CMOS de Circuit Integrat d'Aplicacions Específiques (ASIC). L'arquitectura ací proposada es basa molt en l'algorisme de l'Ordinador Digital de Rotació de Coordenades (CORDIC), que és un algorisme simple i eficient adequat per implementacions VLSI. El receptor fa front a les deficiències inherents a la transmissió de canals sense fil i els cristalls del receptor. Esta tesi també analitza la metodologia adoptada i presenta els resultats de l'execució. Es presenta el rendiment del receptor i es compara amb els obtinguts per mitjà de simulacions. D'altra banda, esta tesi també presenta l'arquitectura i els algorismes d'un receptor de DVB-S2 de cara a la seua implementació en ASIC. No obstant això, a diferència del receptor ISDB-T, només s'introdueixen resultats preliminars d'implementació en ASIC. Això es va fer principalment amb la finalitat de tenir una estimació primerenca de la zona de dau per demostrar que el projecte en ASIC és econòmicament viable, així com per verificar possibles errors en l'etapa primerenca. Com en el cas del receptor ISDB-T, este receptor es basa molt en l'algorisme CORDIC i va ser un prototip de FPGA. La metodologia utilitzada per al segon receptor es deriva de la utilitzada per al receptor IRodrigues De Lima, E. (2016). Architecture and algorithms for the implementation of digital wireless receivers in FPGA and ASIC: ISDB-T and DVB-S2 cases [Tesis doctoral no publicada]. Universitat Politècnica de València. https://doi.org/10.4995/Thesis/10251/61967TESI

Synchronization in digital communication systems: performance bounds and practical algorithms

Communication channels often transfer signals from different transmitters. To avoid interference the available frequency spectrum is divided into non-overlapping frequency bands (bandpass channels) and each transmitter is assigned to a different bandpass channel. The transmission of a signal over a bandpass channel requires a shift of its frequency-content to a frequency range that is compatible with the designated frequency band (modulation). At the receiver, the modulated signal is demodulated (frequency shifted back to the original frequency band) in order to recover the original signal. The modulation/demodulation process requires the presence of a locally generated sinusoidal signal at both the transmitter and the receiver. To enable a reliable information transfer, it is imperative that these two sinusoids are accurately synchronized. Recently, several powerful channel codes have been developed which enable reliable communication at a very low signal-to-noise ratio (SNR). A by-product of these developments is that synchronization must now be performed at a SNR that is lower than ever before. Of course, this imposes high requirements on the synchronizer design. This doctoral thesis investigates to what extent (performance bounds) and in what way (practical algorithms) the structure that the channel code enforces upon the transmitted signal can be exploited to improve the synchronization accuracy at low SNR