1,702 research outputs found
Fast jitter tolerance testing for high-speed serial links in post-silicon validation
Post-silicon electrical validation of high-speed input/output (HSIO) links is a critical process for product qualification schedules of high-performance computer platforms under current aggressive time-to-market (TTM) commitments. Improvements in signaling methods, circuits, and process technologies have allowed HSIO data rates to scale well beyond 10 Gb/s. Noise and EM effects can create multiple signal integrity problems, which are aggravated by continuously faster bus technologies. The goal of post-silicon validation for HSIO links is to ensure design robustness of both receiver (Rx) and transmitter (Tx) circuitry in real system environments. One of the most common ways to evaluate the performance of a HSIO link is to characterize the Rx jitter tolerance (JTOL) performance by measuring the bit error rate (BER) of the link under worst stressing conditions. However, JTOL testing is extremely time-consuming when executed at specification BER considering manufacturing process, voltage, and temperature (PVT) test coverage. In order to significantly accelerate this process, we propose a novel approach for JTOL testing based on an efficient direct search optimization methodology. Our approach exploits the fast execution of a modified golden section search with a high BER, while overcoming the lack of correlation between different BERs by performing a downward linear search at the actual target BER until no errors are found. Our proposed methodology is validated in a realistic industrial server post-silicon validation platform for three different computer HSIO links: SATA, USB3, and PCIe3.ITESO, A.C
Jitter Tolerance Acceleration Using the Golden Section Optimization Technique
Post-silicon validation of high-speed input/output (HSIO) links is a critical process for product qualification schedules of computer platforms under the current time-to-market (TTM) commitments. The goal of post-silicon validation for HSIO links is to confirm design robustness of both receiver (Rx) and transmitter (Tx) circuitry in a real application environment. One of the most common ways to evaluate the performance of a HSIO link is to characterize the Rx jitter tolerance (JTOL) performance by measuring the bit error rate (BER) through the link under worst stressing conditions. However, JTOL testing is very time-consuming when executing at specification BER, and the testing time is extremely increased when considering manufacturing process, voltage, and temperature (PVT) test coverage for a qualification decision. In order to speed up this process, we propose a new approach for JTOL testing based on the golden section algorithm. The proposed method takes advantage of the fast execution of the golden section search with a high BER, while overcoming the lack of correlation between different BERs by performing a downward linear search at the actual target BER until no errors are seen. Our proposed methodology is validated by implementing it in a server HSIO link
Fast And Accurate Receiver Jitter Tolerance Extrapolation Using The Q-Factor Linear Fitting Method
A performance bit rates of more than 6 Gb/s is deemed as a common standard in high-speed interconnect system in conjunction with the recent enhancement of high-speed serial interface (HSSI). In industry, receiver (Rx) jitter tolerance (JTOL) measurement required to characterize the high-speed interconnect. Time required for conventional methods to complete Rx JTOL measurement for low bit error rate (BER) values normally took a week’s time depending on the data rate. In addition, a large number of bits is required to be transmitted hence resulting measurement cost as inefficient. This research project implements a method known as Q-factor linear fitting method to reduce the measurement time of the Rx JTOL at low BER by using high BER data. The result shows that the measurement of Rx JTOL using Q-factor linear fitting method using BER 10-10 data achieved 11x speed-up in comparison to direct measurement of Rx JTOL. The proposed methods of combined different level of BER values and increase more data points of higher BER able to significantly improve the accuracy of the Rx JTOL measurement result. The proposed method is successfully established in the experiment where the results obtained indicated relative error of Rx JTOL using Q-factor linear fitting method of BER 10-10 data are reduced from 9.47% to 3.31% after combining with the BER 10-11 data and relative error for Rx JTOL extrapolation measurement using BER 10-10 data at low temperature (-25˚C) is reduced from 9.47% to 5.43% by increasing the measurement data point from 20 data points to 30 data point
Design of a low-cost high speed data capture card for the Hubble Sphere Hydrogen Survey
Includes bibliographical references (leaves 101-105).This thesis describes the design and implementation of a low-cost high speed data capture card for the Hubble Sphere Hydrogen Survey (HSHS). The Hubble Space Hydrogen Survey was initiated in an effort to build a low-cost cylindrical radio telescope for an all sky redshift survey with the observational goal to produce a 3-dimensional mapping of the bulk Hubble Sphere using Hydrogen 21cm emissions. This dissertation ï¬ rst investigates the system design to see how each of the user speciï¬ cations set by the planning team could be achieved in terms of design decisions, component selection and schematic capture. The final design. AstroGIG, satisï¬ es the user speciï¬ cations by capturing data up to a full power bandwidth of 1.7GHz with an instantaneous bandwidth of ≤ 250MHz white maximizing the dynamic range. AstroGIG buffers, processes, stores and ï¬ nally transmits the data through a 4-lane PCI-Express interface to a standard PC where the majority of the processing is performed. The system implementation is then described where issues relating to the process of transforming schematics into a physical PCB, and HSHS integration are discussed. The design is veriï¬ ed through Hyperlynx simulations to give a high degree of certainty that physical implementation and production would be successful. Results from tests on the actual hardware characterizing the overall system performance are presented. Conclusions are drawn based on these results and suggestions for future work and design improvements are recommended
Space telescope phase B definition study. Volume 2A: Science instruments, f24 field camera
The analysis and design of the F/24 field camera for the space telescope are discussed. The camera was designed for application to the radial bay of the optical telescope assembly and has an on axis field of view of 3 arc-minutes by 3 arc-minutes
A high speed serializer/deserializer design
A Serializer/Deserializer (SerDes) is a circuit that converts parallel data into a serial stream and vice versa. It helps solve clock/data skew problems, simplifies data transmission, lowers the power consumption and reduces the chip cost. The goal of this project was to solve the challenges in high speed SerDes design, which included the low jitter design, wide bandwidth design and low power design.
A quarter-rate multiplexer/demultiplexer (MUX/DEMUX) was implemented. This quarter-rate structure decreases the required clock frequency from one half to one quarter of the data rate. It is shown that this significantly relaxes the design of the VCO at high speed and achieves lower power consumption.
A novel multi-phase LC-ring oscillator was developed to supply a low noise clock to the SerDes. This proposed VCO combined an LC-tank with a ring structure to achieve both wide tuning range (11%) and low phase noise (-110dBc/Hz at 1MHz offset).
With this structure, a data rate of 36 Gb/s was realized with a measured peak-to-peak jitter of 10ps using 0.18microm SiGe BiCMOS technology. The power consumption is 3.6W with 3.4V power supply voltage. At a 60 Gb/s data rate the simulated peak-to-peak jitter was 4.8ps using 65nm CMOS technology. The power consumption is 92mW with 2V power supply voltage.
A time-to-digital (TDC) calibration circuit was designed to compensate for the phase mismatches among the multiple phases of the PLL clock using a three dimensional fully depleted silicon on insulator (3D FDSOI) CMOS process. The 3D process separated the analog PLL portion from the digital calibration portion into different tiers. This eliminated the noise coupling through the common substrate in the 2D process. Mismatches caused by the vertical tier-to-tier interconnections and the temperature influence in the 3D process were attenuated by the proposed calibration circuit.
The design strategy and circuits developed from this dissertation provide significant benefit to both wired and wireless applications
Recommended from our members
Architectures and Circuits Leveraging Injection-Locked Oscillators for Ultra-Low Voltage Clock Synthesis and Reference-less Receivers for Dense Chip-to-Chip Communications
High performance computing is critical for the needs of scientific discovery and economic competitiveness. An extreme-scale computing system at 1000x the performance of today’s petaflop machines will exhibit massive parallelism on multiple vertical fronts, from thousands of computational units on a single processor to thousands of processors in a single data center. To facilitate such a massively-parallel extreme-scale computing, a key challenge is power. The challenge is not power associated with base computation but rather the problem of transporting data from one chip to another at high enough rates. This thesis presents architectures and techniques to achieve low power and area footprint while achieving high data rates in a dense very-short reach (VSR) chip-to-chip (C2C) communication network. High-speed serial communication operating at ultra-low supplies improves the energy-efficiency and lowers the power envelop of a system doing an exaflop of loops. One focus area of this thesis is clock synthesis for such energy-efficient interconnect applications operating at high speeds and ultra-low supplies. A sub-integer clockfrequency synthesizer is presented that incorporates a multi-phase injection-locked ring-oscillator-based prescaler for operation at an ultra-low supply voltage of 0.5V, phase-switching based programmable division for sub-integer clock-frequency synthesis, and automatic calibration to ensure injection lock. A record speed of 9GHz has been demonstrated at 0.5V in 45nm SOI CMOS. It consumes 3.5mW of power at 9.12GHz and 0.052 of area, while showing an output phase noise of -100dBc/Hz at 1MHz offset and RMS jitter of 325fs; it achieves a net of -186.5 in a 45-nm SOI CMOS process. This thesis also describes a receiver with a reference-less clocking architecture for high-density VSR-C2C links. This architecture simplifies clock-tree planning in dense extreme-scaling computing environments and has high-bandwidth CDR to enable SSC for suppressing EMI and to mitigate TX jitter requirements. It features clock-less DFE and a high-bandwidth CDR based on master-slave ILOs for phase generation/rotation. The RX is implemented in 14nm CMOS and characterized at 19Gb/s. It is 1.5x faster that previous reference-less embedded-oscillator based designs with greater than 100MHz jitter tolerance bandwidth and recovers error-free data over VSR-C2C channels. It achieves a power-efficiency of 2.9pJ/b while recovering error-free data (BER 200MHz and the INL of the ILO-based phase-rotator (32- Steps/UI) is <1-LSB. Lastly, this thesis develops a time-domain delay-based modeling of injection locking to describe injection-locking phenomena in nonharmonic oscillators. The model is used to predict the locking bandwidth, and the locking dynamics of the locked oscillator. The model predictions are verified against simulations and measurements of a four-stage differential ring oscillator. The model is further used to predict the injection-locking behavior of a single-ended CMOS inverter based ring oscillator, the lock range of a multi-phase injection-locked ring-oscillator-based prescaler, as well as the dynamics of tracking injection phase perturbations in injection-locked masterslave oscillators; demonstrating its versatility in application to any nonharmonic oscillator
A Framework for the Evaluation of Distributed Control Systems in Industrial Control Applications
The research develops a test-bench and framework to evaluate distributed control systems (DCSs) against industrial control system requirements. A real-time hardware-in-the-loop (HIL) test-bench and framework has been used for the evaluation of a DeltaV M3 DCS from Emerson Process Management. The test-bench measures: process control behaviour including overshoot and settling time; and I/O throughput, latency, and jitter for analog, digital, Modbus serial and OPC over Ethernet. The DCS successfully controls a real-time Matlab simulation model of a Nuclear Power Plant (NPP) steam generator, with a maximum water-level overshoot of 4.20%. The evaluated DCS has I/O throughput between 1.06 and 5.05 Hz, and latencies between 72 and 310 ms. The OPC over Ethernet is the most deterministic I/O channel, but has the lowest throughput. The test-bench and framework enables the evaluation of new technology for use in NPP and many other industrial control applications
- …