Analog/RF Circuit Design Techniques for Nanometerscale IC Technologies

CMOS evolution introduces several problems in analog design. Gate-leakage mismatch exceeds conventional matching tolerances requiring active cancellation techniques or alternative architectures. One strategy to deal with the use of lower supply voltages is to operate critical parts at higher supply voltages, by exploiting combinations of thin- and thick-oxide transistors. Alternatively, low voltage circuit techniques are successfully developed. In order to benefit from nanometer scale CMOS technology, more functionality is shifted to the digital domain, including parts of the RF circuits. At the same time, analog control for digital and digital control for analog emerges to deal with current and upcoming imperfections

Analysis And Design Of Wideband Passive Mixer-First Receivers

This dissertation focuses on the design of wideband SAW-less receivers for softwaredefined radios. The entire body of work is based on a single RF front-end architecture type: a passive mixer connected directly to the antenna port of the radio, without an LNA or matching network up front. This structure is inherently wideband which allows for a single receiver front-end to operate at a wide range of frequencies, as tuned by its local oscillator (LO). Additionally, the mixer exhibits the property of transparency from the baseband port of the radio to the RF port of the radio, and vice versa. The focus of the first half of the thesis is on developing a simple theoretical framework for the impedance characteristics of the passive mixer, and implementing a maximally flexible receiver which utilizes the mixer's transparency to the fullest extent. Additionally, it is shown that mixing with 8 non-overlapping phases instead of the traditional 4 has benefits beyond harmonic rejection extending to improved noise performance and increased impedance tuning range. This receiver exhibits low noise figure (~3dB), excellent wideband linearity (IIP3[GREATER-THAN OR EQUAL TO]25dBm), and unprecedented RF impedance control from the baseband side of the passive mixer. Another wideband receiver is presented which explores increasing the number of LO phases even further to 16 and 32, increasing the impedance matching range. The same chip contains a circuit technique for alleviating the shunting effects of LO phase overlap on mixer conversion gain, noise, and impedance match range. Finally in a new design, the power consumption of the receiver architecture is decreased by a factor of 5x (and not scaling with RF frequency). This is done using a resonant LO drive with 8 non-overlapping phases, incorporating the large mixer gate capacitance directly into the LC tank of the VCO. Baseband power consumption is also reduced by reusing current in the four baseband amplifier channels, and performing harmonic rejection, all in one stage of amplification

An in-band full-duplex radio receiver with a passive vector modulator downmixer for self-interference cancellation

In-band full-duplex (FD) wireless, i.e., simultaneous transmission and reception at the same frequency, introduces strong self-interference (SI) that masks the signal to be received. This paper proposes a receiver in which a copy of the transmit signal is fed through a switched-resistor vector modulator (VM)that provides simultaneous downmixing, phase shift, and amplitude scaling and subtracts it in the analog baseband for up to 27 dB SI-cancellation. Cancelling before active baseband amplification avoids self-blocking, and highly linear mixers keep SIinduced distortion low, for a receiver SI-to-noise-and-distortionratio (SINDR) of up to 71.5 dB in 16.25 MHz BW. When combined with a two-port antenna with only 20 dB isolation, the low RX distortion theoretically allows sufficient digital cancellation for over 90 dB link budget, sufficient for short-range, low-power FD links

Architectures and Circuit Techniques for High-Performance Field-Programmable CMOS Software Defined Radios

Next-generation wireless communication systems put more stringent performance requirements on the wireless RF receiver circuits. Sensitivity, linearity, bandwidth and power consumption are some of the most important specifications that often face tightly coupled tradeoffs between them. To increase the data throughput, a large number of fragmented spectrums are being introduced to the wireless communication standards. Carrier aggregation technology needs concurrent communication across several non-contiguous frequency bands, which results in a rapidly growing number of band combinations. Supporting all the frequency bands and their aggregation combinations increases the complexity of the RF receivers. Highly flexible software defined radio (SDR) is a promising technology to address these applications scenarios with lower complexity by relaxing the specifications of the RF filters or eliminating them. However, there are still many technology challenges with both the receiver architecture and the circuit implementations. The performance requirements of the receivers can also vary across different application scenario and RF environments. Field-programmable dynamic performance tradeoff can potentially reduce the power consumption of the receiver. In this dissertation, we address the performance enhancement challenges in the wideband SDRs by innovations at both the circuit building block level and the receiver architecture level. A series of research projects are conducted to push the state-of-the-art performance envelope and add features such as field-programmable performance tradeoff and concurrent reception. The projects originate from the concept of thermal noise canceling techniques and further enhance the RF performance and add features for more capable SDR receivers. Four generations of prototype LNA or receiver chips are designed, and each of them pushes at least one aspect of the RF performance such as bandwidth, linearity, and NF. A noise-canceling distributed LNA breaks the tradeoff between NF and RF bandwidth by introducing microwave circuit techniques from the distributed amplifiers. The LNA architecture uniquely provides ultra high bandwidth and low NF at low frequencies. A family of field-programmable LNA realized field-programmable performance tradeoff with current-reuse programmable transconductance cells. Interferer-reflecting loops can be applied around the LNAs to improve their input linearity by rejecting the out-of-band interferers with a wideband low in- put impedance. A low noise transconductance amplifier (LNTA) that operates in class-AB-C is invented to can handle rail-to-rail out-of-band blocker without saturation. Class-AB and class-C transconductors form a composite amplifier to increase the linear range of the input voltage. A new antenna interface named frequency-translational quadrature-hybrid (FTQH) breaks the input impedance matching requirement of the LNAs by introducing quadrature hybrid couplers to the CMOS RFIC design. The FTQH receiver achieves wideband sub-1dB NF and supports scalable massive frequency-agile concurrent reception

Configurable circuits and their impact on multi-standard RF front-end architectures

This thesis studies configurable circuits and their impact on multi-standard RF front-end architectures. In particular, low-voltage low-power linear LNA and mixer topologies suitable for implementation in multi-standard front-ends are subject of the investigation. With respect to frequency and bandwidth, multi-standard front-ends can be implemented using either tunable or wideband LNA and mixer topologies. Based on the type of the LNA and mixer(s), multi-standard receiver RF front-ends can be divided into three groups. They can be (tunable) narrow-band, wide-band or combined. The advantages and disadvantages of the different multi-standard receiver RF front-ends have been discussed in detail. The partitioning between off-chip selectivity, on-chip selectivity provided by the LNA and mixer, linearity, power consumption and occupied chip area in each multi-standard RF front-end group are thoroughly investigated. A Figure of Merit (FOM) for the multi-standard receiver RF front-end has been introduced. Based on this FOM the most suitable multi-standard RF front-end group in terms of cost-effectiveness can be selected. In order to determine which multi-standard RF front-end group is the most cost-effective for a practical application, a GSM850/E-GSM/DCS/PCS/Bluetooth/WLANa/b/g multi-standard receiver RF front-end is chosen as a demonstrator. These standards are the most frequently used standards in wireless communication, and this combination of standards allows to users almost "anytime-anywhere" voice and data transfer. In order to verify these results, three demonstrators have been defined, designed and implemented, two wideband RF front-end circuits in 90nm CMOS and 65nm CMOS, and one combined multi-standard RF front-end circuit in 65nm CMOS. The proposed multi-standard demonstrators have been compared with the state-of the art narrow-band, wide-band and combined multi-standard RF front-ends. On the proposed multi-standard RF front-ends and the state-of the art multi-standard RF front-ends the proposed FOM have been applied. The comparison shows that the combined multi-standard RF front-end group is the most cost effective multi-standard group for this application

Switched-Capacitor RF Receivers for High Interferer Tolerance

The demand for broadband wireless communication is growing rapidly, requiring more spectrum resources. However, spectrum usage is inefficient today because different frequency bands are allocated for different communication standards and most of the bands are not highly occupied. Cognitive radio systems with dynamic spectrum access improve spectrum efficiency, but they require wideband tunable receiver hardware. In such a system, a preselect filter is required for the RF receiver front end, because an out-of-band (OB) interferer can block the front end or cause distortion, desensitizing the receiver. In a conventional solution, off-chip passive filters, such as surface-acoustic-wave (SAW) filters, are used to reject the OB interferer. However, such passive filters are hardly tunable, have large area, and are very expensive. On-chip, high-selectivity, linearly tunable RF filters are, therefore, a hot topic in RF front-end research. Switched-capacitor (SC) RF filters, such as N-path filters, feature good linearity and tunability, making them good candidates for tunable RF filters. However, N-path filters have some drawbacks: notably, a poor harmonic response and limited close-by blocker tolerance. This thesis presents the design and implementation of several interferer-tolerant receivers based on SC technology. We present an RF receiver with a harmonic-rejecting N-path filter to improve the harmonic response of the N-path bandpass filter. It features tunable narrowband filtering and high attenuation of the third- and fifth-order LO harmonics at the LNA output, which improves the blocker tolerance at LO harmonics. The 0.2-1 GHz RF receiver is implemented in a 65 nm CMOS process. The blocker 1 dB compression point (B1dB) is -2.4 dBm at a 20 MHz offset, and remains high at the third- and fifth-order LO harmonics. The LNA’s reverse isolation helps keep the LO emission below -90 dBm. A two-stage harmonic-rejection approach offers a > 51 dB harmonic-rejection ratio at the third- and fifth-order LO harmonics without calibration. To improve tolerance for close-by blockers, we further present an SC RF receiver achieving high-order, tunable, highly linear RF filtering. We implement RF input impedance matching, N-path filtering, high-order discrete-time infinite-impulse response (IIR) filtering and downconversion using only switches and capacitors in a 0.1-0.7 GHz prototype with tunable center frequency, programmable filter order, and very high tolerance for OB blockers. The 40 nm CMOS receiver consumes 38.5-76.5mA, achieves 40 dB gain, 24 dBm OB IIP3, 14.7 dBm B1dB for a 30MHz blocker offset, 6.8-9.7 dB noise figure, and > 66dB calibrated harmonic rejection ratio. The key drawback of our earlier SC receiver is the relatively high theoretical lower limit of the noise figure. To improve the noise performance, we developed a 0.1-0.6 GHz chopping SC RF receiver with an integrated blocker detector. We achieve RF impedance matching, high-order OB interferer filtering, and flicker-noise chopping with passive SC circuits only. The 34-80 mW 65 nm receiver achieves 35 dB gain, 4.6-9 dB NF, 31 dBm OB-IIP3, and 15 dBm B1dB. The 0.2 mW integrated blocker detector detects large OB blockers with only a 1 us response time. The filter order can be adapted to blocker power with the blocker detector

Low Power Continuous-time Bandpass Delta-Sigma Modulators.

Low power techniques for continuous-time bandpass delta-sigma modulators (CTBPDSMs) are introduced. First, a 800MS/s low power 4th-order CTBPDSM with 24MHz bandwidth at 200MHz IF is presented. A novel power-efficient resonator with a single amplifier is used in the loopfilter. A single op-amp resonator makes use of positive feedback to increase the quality factor. Also, a new 4th-order architecture is introduced for system simplicity and low power. Low power consumption and a simple modulator structure are achieved by reducing the number of feedback DACs. This modulator achieves 58dB SNDR, and the total power consumption is 12mW. Second, a 6th-order CTBPDSM with duty cycle controlled DACs is presented. This prototype introduces new architecture for low power consumption and other important features. Duty cycle control enables the use of a single DAC per resonator without degrading the signal transfer function (STF), and helps to lower power consumption, low area, and thermal noise. This ADC provides input signal filtering, and increases the dynamic range by reducing the peaking in the STF. Furthermore, the center frequency is tunable so that the CTBPDSM is more useful in the receiver. The prototype second modulator achieves 69dB SNDR, and consumes 35mW, demonstrating the best FoM of 320fJ/conv.-step for CTBPDSMs using active resonators. The techniques introduced in this research help CTBPDSMs have good power efficiency compared with the other kinds of ADCs, and make the implement of a software-defined radio architecture easier which is appropriate for the future multiple standard radio receivers without a power penalty.PHDElectrical EngineeringUniversity of Michigan, Horace H. Rackham School of Graduate Studieshttp://deepblue.lib.umich.edu/bitstream/2027.42/98001/1/hichae_1.pd

RF Frontend for Spectrum Analysis in Cognitive Radio

Advances in wireless technology have sparked a plethora of mobile communication standards to support a variety of applications. FCC predicts a looming crisis due to the exponentially growing demand for spectrum and it recommends to increase the efficiency of spectrum utilization. Cognitive Radio (CR) is envisioned as a radio technology which detects and exploits empty spectrum to improve the quality of communication. Spectrum analyzer for detecting spectrum holes is a key component required for implementing cognitive radio. Mitola's vision of using an RF Analog-to-Digital (ADC) to digitize the entire spectrum is not yet a reality. The traditional spectrum analysis technique based on a RF Front end using an LO Sweep is too slow, making it unsuitable to track fast hopping signals. In this work, we demonstrate an RF Frontend that can simplify the ADC's requirement by splitting the input spectrum into multiple channels. It avoids the problem of PLL settling by incorporating LO synthesis within the signal path using a concept called Iterative Down Converter. An example 0.75GHz-11.25GHz RF Channelizer is designed in 65nm Standard CMOS Process. The channelizer splits the input spectrum (10.5GHz bandwidth) into seven channels (each of bandwidth 1.5GHz). The channelizer shows the ability to rapidly switch from one channel to another (within a few ns) as well as down-converting multiple channels simultaneously (concurrency). The channelizer achieves a dynamic range of 54dB for a bandwidth of 10.5GHz, while consuming 540mW of power. Harmonic rejection mixer plays a key role in a broadband receiver. A novel order scalable harmonic rejection mixer architecture is described in this research. A proof-of-principle prototype has been designed and fabricated in a 45nm SOI technology. Experimental results demonstrate an operation range of 0.5GHz to 1.5GHz for the LO frequency while offering harmonic rejection better than 55dB for the 3rd harmonic and 58dB for the 5th harmonic across LO frequencies. While cognitive radio solves the spectrum efficiency problem in frequency domain, the electronic beam steering provides a spatial domain solution. Electronic beam forming using phased arrays have been claimed to improve spectrum efficiency by serving more number of users for a given bandwidth. A LO path phase-shifter with frequency-doubling is demonstrated for WiMAX applications

RF Frontend for Spectrum Analysis in Cognitive Radio

Advances in wireless technology have sparked a plethora of mobile communication standards to support a variety of applications. FCC predicts a looming crisis due to the exponentially growing demand for spectrum and it recommends to increase the efficiency of spectrum utilization. Cognitive Radio (CR) is envisioned as a radio technology which detects and exploits empty spectrum to improve the quality of communication. Spectrum analyzer for detecting spectrum holes is a key component required for implementing cognitive radio. Mitola's vision of using an RF Analog-to-Digital (ADC) to digitize the entire spectrum is not yet a reality. The traditional spectrum analysis technique based on a RF Front end using an LO Sweep is too slow, making it unsuitable to track fast hopping signals. In this work, we demonstrate an RF Frontend that can simplify the ADC's requirement by splitting the input spectrum into multiple channels. It avoids the problem of PLL settling by incorporating LO synthesis within the signal path using a concept called Iterative Down Converter. An example 0.75GHz-11.25GHz RF Channelizer is designed in 65nm Standard CMOS Process. The channelizer splits the input spectrum (10.5GHz bandwidth) into seven channels (each of bandwidth 1.5GHz). The channelizer shows the ability to rapidly switch from one channel to another (within a few ns) as well as down-converting multiple channels simultaneously (concurrency). The channelizer achieves a dynamic range of 54dB for a bandwidth of 10.5GHz, while consuming 540mW of power. Harmonic rejection mixer plays a key role in a broadband receiver. A novel order scalable harmonic rejection mixer architecture is described in this research. A proof-of-principle prototype has been designed and fabricated in a 45nm SOI technology. Experimental results demonstrate an operation range of 0.5GHz to 1.5GHz for the LO frequency while offering harmonic rejection better than 55dB for the 3rd harmonic and 58dB for the 5th harmonic across LO frequencies. While cognitive radio solves the spectrum efficiency problem in frequency domain, the electronic beam steering provides a spatial domain solution. Electronic beam forming using phased arrays have been claimed to improve spectrum efficiency by serving more number of users for a given bandwidth. A LO path phase-shifter with frequency-doubling is demonstrated for WiMAX applications