Receptores de rádio-frequência melhorados e disruptivos

This Ph.D. mainly addresses the reception part of a radio front end, focusing on Radio Frequency (RF) sampling architectures. These are considered to be the most promising future candidates to get better performance in terms of bandwidth and agility, following the well-known Software-Defined Radio (SDR) concept. The study considers the usage of an RF receiver in a standalone operation, i.e., used for receiving unknown data at the antenna, and when used as observation path for Power Amplifier (PA) linearization via Digital Predistortion (DPD), since nowadays this represents a mandatory technique to increase overall system’s performance. Firstly, commercial available RF Analog-Digital-Converters (ADCs) are studied and characterized to understand their limitations when used in DPD scenarios. A method for characterization and digital post-compensation to improve performance is proposed and evaluated. Secondly, an innovative FPGA-based RF single-bit pulsed converter based on Pulse Width Modulation (PWM) is addressed targeting frequency agility, high analog input bandwidth, and system integration, taking profit of an FPGA-based implementation. The latter was optimized based on PWM theoretical behavior maximizing Signal-to-Noise-Ratio (SNR) and bandwidth. The optimized receiver, was afterwards evaluated in a 5G C-RAN architecture and as a feedback loop for DPD. Finally, a brief study regarding DPD feedback loops in the scope of multiantenna transmitters is presented. This Ph.D. contributes with several advances to the state-of-the-art of SDR receiver, and to the so-called SDR DPD concept.Este doutoramento endereça principalmente a componente de receção de um transcetor de rádio-frequência (RF), focando-se em arquiteturas de receção de amostragem em RF. Estas são assim consideradas como sendo as mais promissoras para o futuro, em termos de desempenho, largura de banda e agilidade, de acordo com o conhecido conceito de Rádios Definidos por Software (SDR). O estudo considera o uso dos recetores de RF em modo standalone, i.e., recebendo dados desconhecidos provenientes da antena, e também quando usados como caminho de observação para aplicação de linearização de amplificadores de potência (PAs) via pré-distorção digital (DPD), pois atualmente esta é uma técnica fundamental para aumentar o desempenho geral do sistema. Em primeiro lugar, os conversores analógico-digital de RF são estudados e caracterizados para perceber as suas limitações quando usados em cenários de DPD. Um método de caracterização e pós compensação digital é proposto para obter melhorias de desempenho. Em segundo lugar, um novo recetor pulsado de um bit baseado em Modulação de Largura de Pulso (PWM) e implementado em Agregado de Células Lógicas Programáveis (FPGA) é endereçado, visando agilidade em frequência, largura de banda analógica e integração de sistema, tirando proveito da implementação em FPGA. Este recetor foi otimizado com base no modelo comportamental teórico da modulação PWM, maximizando a relação sinalruído (SNR) e a largura de banda. O recetor otimizado foi posteriormente avaliado num cenário 5G de uma arquitetura C-RAN e também num cenário em que serve de caminho de observação para DPD. Finalmente, um breve estudo relativo a caminhos de observação de DPD no contexto de transmissores multi-antena é também apresentado. Este doutoramento contribui com vários avanços no estado da arte de recetores SDR e no conceito de SDR DPD.Programa Doutoral em Engenharia Eletrotécnic

Microwave resonant sensors

Microwave resonant sensors use the spectral characterisation of a resonator to make high sensitivity measurements of material electromagnetic properties at GHz frequencies. They have been applied to a wide range of industrial and scientific measurements, and used to study a diversity of physical phenomena. Recently, a number of challenging dynamic applications have been developed that require very high speed and high performance, such as kinetic inductance detectors and scanning microwave microscopes. Others, such as sensors for miniaturised fluidic systems and non-invasive blood glucose sensors, also require low system cost and small footprint. This thesis investigates new and improved techniques for implementing microwave resonant sensor systems, aiming to enhance their suitability for such demanding tasks. This was achieved through several original contributions: new insights into coupling, dynamics, and statistical properties of sensors; a hardware implementation of a realtime multitone readout system; and the development of efficient signal processing algorithms for the extraction of sensor measurements from resonator response data. The performance of this improved sensor system was verified through a number of novel measurements, achieving a higher sampling rate than the best available technology yet with equivalent accuracy and precision. At the same time, these experiments revealed unforeseen applications in liquid metrology and precision microwave heating of miniature flow systems.EThOS - Electronic Theses Online ServiceGBUnited Kingdo

Dirty RF Signal Processing for Mitigation of Receiver Front-end Non-linearity

Moderne drahtlose Kommunikationssysteme stellen hohe und teilweise gegensätzliche Anforderungen an die Hardware der Funkmodule, wie z.B. niedriger Energieverbrauch, große Bandbreite und hohe Linearität. Die Gewährleistung einer ausreichenden Linearität ist, neben anderen analogen Parametern, eine Herausforderung im praktischen Design der Funkmodule. Der Fokus der Dissertation liegt auf breitbandigen HF-Frontends für Software-konfigurierbare Funkmodule, die seit einigen Jahren kommerziell verfügbar sind. Die praktischen Herausforderungen und Grenzen solcher flexiblen Funkmodule offenbaren sich vor allem im realen Experiment. Eines der Hauptprobleme ist die Sicherstellung einer ausreichenden analogen Performanz über einen weiten Frequenzbereich. Aus einer Vielzahl an analogen Störeffekten behandelt die Arbeit die Analyse und Minderung von Nichtlinearitäten in Empfängern mit direkt-umsetzender Architektur. Im Vordergrund stehen dabei Signalverarbeitungsstrategien zur Minderung nichtlinear verursachter Interferenz - ein Algorithmus, der besser unter "Dirty RF"-Techniken bekannt ist. Ein digitales Verfahren nach der Vorwärtskopplung wird durch intensive Simulationen, Messungen und Implementierung in realer Hardware verifiziert. Um die Lücken zwischen Theorie und praktischer Anwendbarkeit zu schließen und das Verfahren in reale Funkmodule zu integrieren, werden verschiedene Untersuchungen durchgeführt. Hierzu wird ein erweitertes Verhaltensmodell entwickelt, das die Struktur direkt-umsetzender Empfänger am besten nachbildet und damit alle Verzerrungen im HF- und Basisband erfasst. Darüber hinaus wird die Leistungsfähigkeit des Algorithmus unter realen Funkkanal-Bedingungen untersucht. Zusätzlich folgt die Vorstellung einer ressourceneffizienten Echtzeit-Implementierung des Verfahrens auf einem FPGA. Abschließend diskutiert die Arbeit verschiedene Anwendungsfelder, darunter spektrales Sensing, robuster GSM-Empfang und GSM-basiertes Passivradar. Es wird gezeigt, dass nichtlineare Verzerrungen erfolgreich in der digitalen Domäne gemindert werden können, wodurch die Bitfehlerrate gestörter modulierter Signale sinkt und der Anteil nichtlinear verursachter Interferenz minimiert wird. Schließlich kann durch das Verfahren die effektive Linearität des HF-Frontends stark erhöht werden. Damit wird der zuverlässige Betrieb eines einfachen Funkmoduls unter dem Einfluss der Empfängernichtlinearität möglich. Aufgrund des flexiblen Designs ist der Algorithmus für breitbandige Empfänger universal einsetzbar und ist nicht auf Software-konfigurierbare Funkmodule beschränkt.Today's wireless communication systems place high requirements on the radio's hardware that are largely mutually exclusive, such as low power consumption, wide bandwidth, and high linearity. Achieving a sufficient linearity, among other analogue characteristics, is a challenging issue in practical transceiver design. The focus of this thesis is on wideband receiver RF front-ends for software defined radio technology, which became commercially available in the recent years. Practical challenges and limitations are being revealed in real-world experiments with these radios. One of the main problems is to ensure a sufficient RF performance of the front-end over a wide bandwidth. The thesis covers the analysis and mitigation of receiver non-linearity of typical direct-conversion receiver architectures, among other RF impairments. The main focus is on DSP-based algorithms for mitigating non-linearly induced interference, an approach also known as "Dirty RF" signal processing techniques. The conceived digital feedforward mitigation algorithm is verified through extensive simulations, RF measurements, and implementation in real hardware. Various studies are carried out that bridge the gap between theory and practical applicability of this approach, especially with the aim of integrating that technique into real devices. To this end, an advanced baseband behavioural model is developed that matches to direct-conversion receiver architectures as close as possible, and thus considers all generated distortions at RF and baseband. In addition, the algorithm's performance is verified under challenging fading conditions. Moreover, the thesis presents a resource-efficient real-time implementation of the proposed solution on an FPGA. Finally, different use cases are covered in the thesis that includes spectrum monitoring or sensing, GSM downlink reception, and GSM-based passive radar. It is shown that non-linear distortions can be successfully mitigated at system level in the digital domain, thereby decreasing the bit error rate of distorted modulated signals and reducing the amount of non-linearly induced interference. Finally, the effective linearity of the front-end is increased substantially. Thus, the proper operation of a low-cost radio under presence of receiver non-linearity is possible. Due to the flexible design, the algorithm is generally applicable for wideband receivers and is not restricted to software defined radios

On-Chip Analog Circuit Design Using Built-In Self-Test and an Integrated Multi-Dimensional Optimization Platform

Nowadays, the rapid development of system-on-chip (SoC) market introduces tremendous complexity into the integrated circuit (IC) design. Meanwhile, the IC fabrication process is scaling down to allow higher density of integration but makes the chips more sensitive to the process-voltage-temperature (PVT) variations. A successful IC product not only imposes great pressure on the IC designers, who have to handle wider variations and enforce more design margins, but also challenges the test procedure, leading to more check points and longer test time. To relax the designers’ burden and reduce the cost of testing, it is valuable to make the IC chips able to test and tune itself to some extent. In this dissertation, a fully integrated in-situ design validation and optimization (VO) hardware for analog circuits is proposed. It implements in-situ built-in self-test (BIST) techniques for analog circuits. Based on the data collected from BIST, the error between the measured and the desired performance of the target circuit is evaluated using a cost function. A digital multi-dimensional optimization engine is implemented to adaptively adjust the analog circuit parameters, seeking the minimum value of the cost function and achieving the desired performance. To verify this concept, study cases of a 2nd/4th active-RC band-pass filter (BPF) and a 2nd order Gm-C BPF, as well as all BIST and optimization blocks, are adopted on-chip. Apart from the VO system, several improved BIST techniques are also proposed in this dissertation. A single-tone sinusoidal waveform generator based on a finite-impulse-response (FIR) architecture, which utilizes an optimization algorithm to enhance its spur free dynamic range (SFDR), is proposed. It achieves an SFDR of 59 to 70 dBc from 150 to 850 MHz after the optimization procedure. A low-distortion current-steering two-tone sinusoidal signal synthesizer based on a mixing-FIR architecture is also proposed. The two-tone synthesizer extends the FIR architecture to two stages and implements an up-conversion mixer to generate the two tones, achieving better than -68 dBc IM3 below 480 MHz LO frequency without calibration. Moreover, an on-chip RF receiver linearity BIST methodology for continuous and discrete-time hybrid baseband chain is proposed. The proposed receiver chain implements a charge-domain FIR filter to notch the two excitation signals but expose the third order intermodulation (IM3) tones. It simplifies the linearity measurement procedure–using a power detector is enough to analyze the receiver’s linearity. Finally, a low cost fully digital built-in analog tester for linear-time-invariant (LTI) analog blocks is proposed. It adopts a time-to-digital converter (TDC) to measure the delays corresponded to a ramp excitation signal and is able to estimate the pole or zero locations of a low-pass LTI system

Microwave resonant sensors

Microwave resonant sensors use the spectral characterisation of a resonator to make high sensitivity measurements of material electromagnetic properties at GHz frequencies. They have been applied to a wide range of industrial and scientific measurements, and used to study a diversity of physical phenomena. Recently, a number of challenging dynamic applications have been developed that require very high speed and high performance, such as kinetic inductance detectors and scanning microwave microscopes. Others, such as sensors for miniaturised fluidic systems and non-invasive blood glucose sensors, also require low system cost and small footprint. This thesis investigates new and improved techniques for implementing microwave resonant sensor systems, aiming to enhance their suitability for such demanding tasks. This was achieved through several original contributions: new insights into coupling, dynamics, and statistical properties of sensors; a hardware implementation of a realtime multitone readout system; and the development of efficient signal processing algorithms for the extraction of sensor measurements from resonator response data. The performance of this improved sensor system was verified through a number of novel measurements, achieving a higher sampling rate than the best available technology yet with equivalent accuracy and precision. At the same time, these experiments revealed unforeseen applications in liquid metrology and precision microwave heating of miniature flow systems

Design and Characterization of Power Converters and Amplifiers for Supply-Modulation based Transmitter Architectures

The rapid evolution of telecommunication systems has strongly influenced our lives, and the way we communicate and exchange information. Nevertheless, much progress is expected to happen in the next years with the introduction of new generations of wireless communications standards, which require signals with large bandwidth and very high Peak-to-Average Power Ratio (PAPR) in order to enhance the spectral efficiency and maximize the data rate. However, such developments can only take place through the evolution of Radio-Frequency (RF) which should be capable of working at higher frequencies, higher bandwidth and with higher efficiencies than before. In order to meet these demanding specifications, transmitter architectures have to evolve from a single linear RF Power-Amplifier (PA) into more complex architectures. Envelope Tracking (ET) is one of the most promising solutions for the efficiency-enhancement of next generation transmitters. The research described in this thesis aims to provide solutions to enhance the efficiency of the RF PA by means of an ET architecture. To this purpose, a novel discrete level supply modulator is investigated, which is based on a direct digital-to-analog power conversion. This supply modulator is capable of synthesizing eight voltage steps by means of three isolated voltage sources, thus behaving like a Power Digital-to-Analog Converter (Power-DAC). A hybrid version of the Power-DAC exploiting very fast GaN devices is developed and tested with an L-band PA achieving efficiency improvement up to 13% with 10 MHz of bandwidth. Furthermore, a monolithic GaN version of the Power-DAC is prototyped and tested with an X-band PA achieving efficiency improvement up to 20% and bandwidth of 20 MHz. This supply modulator is tested with outphasing PAs showing promising results with modulated signals and efficiency improvement up to 9%. Finally, dispersive phenomena, which affect PAs and switches in supply modulators, are investigated, characterized and modeled

Vidutinių dažnių 5G belaidžių tinklų galios stiprintuvų tyrimas

This dissertation addresses the problems of ensuring efficient radio fre-quency transmission for 5G wireless networks. Taking into account, that the next generation 5G wireless network structure will be heterogeneous, the device density and their mobility will increase and massive MIMO connectivity capability will be widespread, the main investigated problem is formulated – increasing the efficiency of portable mid-band 5G wireless network CMOS power amplifier with impedance matching networks. The dissertation consists of four parts including the introduction, 3 chapters, conclusions, references and 3 annexes. The investigated problem, importance and purpose of the thesis, the ob-ject of the research methodology, as well as the scientific novelty are de-fined in the introduction. Practical significance of the obtained results, defended state-ments and the structure of the dissertation are also included. The first chapter presents an extensive literature analysis. Latest ad-vances in the structure of the modern wireless network and the importance of the power amplifier in the radio frequency transmission chain are de-scribed in detail. The latter is followed by different power amplifier archi-tectures, parameters and their improvement techniques. Reported imped-ance matching network design methods are also discussed. Chapter 1 is concluded distinguishing the possible research vectors and defining the problems raised in this dissertation. The second chapter is focused around improving the accuracy of de-signing lumped impedance matching network. The proposed methodology of estimating lumped inductor and capacitor parasitic parameters is dis-cussed in detail provi-ding complete mathematical expressions, including a summary and conclusions. The third chapter presents simulation results for the designed radio fre-quency power amplifiers. Two variations of Doherty power amplifier archi-tectures are presented in the second part, covering the full step-by-step de-sign and simulation process. The latter chapter is concluded by comparing simulation and measurement results for all designed radio frequency power amplifiers. General conclusions are followed by an extensive list of references and a list of 5 publications by the author on the topic of the dissertation. 5 papers, focusing on the subject of the discussed dissertation, have been published: three papers are included in the Clarivate Analytics Web of Sci-ence database with a citation index, one paper is included in Clarivate Ana-lytics Web of Science database Conference Proceedings, and one paper has been published in unreferred international conference preceedings. The au-thor has also made 9 presentations at 9 scientific conferences at a national and international level.Dissertatio

Proceedings of the Second International Mobile Satellite Conference (IMSC 1990)

Presented here are the proceedings of the Second International Mobile Satellite Conference (IMSC), held June 17-20, 1990 in Ottawa, Canada. Topics covered include future mobile satellite communications concepts, aeronautical applications, modulation and coding, propagation and experimental systems, mobile terminal equipment, network architecture and control, regulatory and policy considerations, vehicle antennas, and speech compression

Atmospheric compensation experiments on free-space optical coherent communication systems

In the last years free-space optical communications systems for wireless links have been proposed, studied, and implemented mainly due to the higher bandwidth that this technology is able to provide. Still, radio frequency (RF) systems have been maintained in practical wireless communications systems due to the improvement of the microwave sources and the development of high speed electronics. Nowadays the circumstances are changing as a consequence of the increasing data-rate needed in terrestrial and outer space communications. The shift from RF systems to optical communication systems in the free space applications provide a wide set of advantageous characteristics that are motivating the use of these optical technologies in detriment of the RF systems. One of the key reasons is the advantage of working with optical wavelengths in compare to the RF spectral band. As well as the already mentioned increase in the available bandwidth due to the fact that higher optical frequencies directly mean wider bandwidths, the use of optical frequencies lead to a better performance in terms of the received power: for equal antenna sizes the received signal goes inversely as the square of the wavelength. Of the most interest, recent coherent optical communication systems address modulation and detection techniques for high spectral efficiency and robustness against transmission impairments. Coherent detection is an advanced detection technique for achieving high spectral efficiency and maximizing power or signal-to-noise (SNR) efficiency, as symbol decisions are made using the in-phase and quadrature signals, allowing information to be encoded in all the available degrees of freedom. In this context, the effects of Earth's atmosphere must be taken into account. Turbulenceinduced wavefront distortions affect the transmitted beam responsible for deterioration of the link bit error rate (BER). The use of adaptive optics to mitigate turbulence-induced phase fluctuations in links employing coherent (synchronous) detection is poised to reduce performance penalties enabling a more capable next generation of free-space optical communications. In this work, we describe the implementation of a free space optical coherent communication system using QPSK modulation and heterodyne downconvertion that uses adaptive optics techniques and digital signal processing to mitigate turbulenceinduced phase fluctuations and channel impairments in coherent receivers. A new method for generating atmospheric turbulence based on binary computer generated holography (BCGH) using binary arrays is presented and its performance is evaluated. The feasibility of FSO coherent systems working with adaptive optics is demonstrated and the system performance in terms of the BER is experimentally evaluated under the influence of atmospheric turbulence. The resulting system performance is compared against the theoretical models. The viability of the approach to improve the system efficiency and sensitivity of coherent receivers is experimentally demonstrated.En los últimos años las comunicaciones ópticas en el espacio libre han sido propuestas, analizadas e implementadas debido, principalmente, al gran ancho de banda disponible mediante esta tecnología. Aún así, en la práctica, los sistemas de radiofrecuencia (RF) han sido mantenidos en las aplicaciones comerciales debido a la mejora de los dispositivos utilizados y al desarrollo de equipos electrónicos con gran velocidad de procesado. Hoy en día la situación está cambiando como consecuencia de un incremento en la tasa de transmisión requerida en sistemas de comunicaciones terrestres y en el espacio exterior. El cambio de sistemas de RF hacia sistemas ópticos en el espacio libre implica una serie de ventajas clave que motiva la transición hacia estas tecnologías. La primera y gran ventaja de trabajar con frecuencias pertenecientes al espectro óptico es el aumento del ancho de banda disponible, ya que trabajar a alta frecuencia implica directamente un incremento en el ancho de banda. Además, la eficiencia en términos de potencia es incrementada, ya que, para un tamaño de antena fijo, la potencia de señal recivida es proporcional al inverso de la longitud de onda al cuadrado. De especial interés es el desarrollo de sistemas de comunicaciones ópticos que utilicen modulaciones complejas, lo que implica una mayor eficiencia espectral y una mayor robustez contra efectos perniciosos introducidos por el canal. La detección coherente es una avanzada técnica que permite un aumento en la eficiencia espectral y maximiza la eficiencia de la potencia recibida. Esto es debido a que los simbolos son demodulados utilizando las señales en fase y cuadratura, aumentando los grados de libertad del sistema. En este contexto, los efectos de la atmósfera sobre las comunicaciones ópticas coherentes deben ser analizadas en detalle. Las turbulencias atmosféricas distorsionan el frente de onda y son responsables del deterioro de la tasa de error en las comunicaciones ópticas en el espacio libre. El uso de óptica adaptativa para mitigar los efectos de turbulencia atmosphérica abre una ventana a la implementación de la próxima generación de sistemas de comunicaciones, basados en tecnologías coherentes. En este trabajo se describe la implementación de un sistema completo de comunicaciones ópticas coherentes utilizando una modulación coherente (QPSK) y detección heterodina. Un sistema de óptica adaptativa y algoritmos de procesado de señal son implementados con el objetivo de mitigar los diferentes efectos introducidos por el canal. Por otro lado, un nuevo método para generar frentes de onda distorsionados por el canal atmosférico es desarrollado y su eficiencia es analizada. Este método se basa en el uso de holografía binaria generada por computador (BCGH) junto con un dispositivo de modulación óptica binaria de bajo coste (DLP). El funcionamiento del sistema completo es verificado y su eficiencia, en términos de tasa de error, son analizados. La eficiencia obtenida experimentalmente es comparada contra los modelos teóricos propuestos en la literatura. La viabilidad del uso de óptica adaptativa para mitigar efectos en sistemas ópticos coherentes es experimentalmente demostrada