An Octave-Range, Watt-Level, Fully-Integrated CMOS Switching Power Mixer Array for Linearization and Back-Off-Efficiency Improvement

The power mixer array is presented as a novel power generation approach for non-constant envelope signals. It comprises several power mixer units that are dynamically turned on and off to improve the linearity and back-off efficiency. At the circuit level, the power mixer unit can operate as a switching amplifier to achieve high peak power efficiency. Additional circuit level linearization and back-off efficiency improvement techniques are also proposed. To demonstrate the feasibility of this idea, a fully-integrated octave-range CMOS power mixer array is implemented in a 130 nm CMOS process. It is operational between 1.2 GHz and 2.4 GHz and can generate an output power of +31.3 dBm into an external 50 Ω load with a PAE of 42% and a gain compression of only 0.4 dB at 1.8 GHz. It achieves a PAE of 25%, at an average output power of +26.4 dBm, and an EVM of 4.6% with a non-constant-envelope 16 QAM signal. It can also produce arbitrary signal levels down to -70 dBm of output power with the 16 QAM-modulated signal without any RF gain control circuit

Hybrid continuous-discrete-time multi-bit delta-sigma A/D converters with auto-ranging algorithm

In wireless portable applications, a large part of the signal processing is performed in the digital domain. Digital circuits show many advantages. The power consumption and fabrication costs are low even for high levels of complexity. A well established and highly automated design flow allows one to benefit from the constant progress in CMOS technologies. Moreover, digital circuits offer robust and programmable signal processing means and need no external components. Hence, the trend in consumer electronics is to further reduce the part of analog signal processing in the receiver chain of wireless transceivers. Consequently, analog-to-digital converters with higher resolutions and bandwidths are constantly required. The ultimate goal is the direct digitization of radio frequency signals, where the conversion would be performed immediately after the front-end amplifier. ΔΣ-modulation-based converters have proved to be the most suitable to achieve the required performance. Switched-capacitor implementations have been widely used over the last two decades. However, recent publications and books have shown that continuous-time architectures can achieve the same performance with lower power consumption. Most designs found throughout the literature use a single- or few-bit internal quantizer with a high-order modulation. As a result, in order to achieve the resolutions and bandwidths required today, the sampling frequency must exceed 100MHz. This approach leads to non-negligible power consumption in the clock generation. Moreover, the presence of such fast squared signals is not suitable for a system-on-chip comprising radio frequency receivers. In this thesis we propose a low-power strategy relying on a large number of internal levels rather than on a high sampling frequency or modulation order. Besides, a hybrid continuous-discrete-time approach is used to take advantage of the accuracy of switched-capacitor circuits and the low power consumption of continuous-time implementation. The sensitivity to clock jitter brought about by the continuous-time stage is reduced by the use of a large number of levels. An auto-ranging algorithm is developed in this thesis to overcome the limitation of a large-size quantizer under low-voltage supply. Finally, the strategy is applied to a design example addressing typical specifications for a Bluetooth receiver with direct conversion

Digital signal processing and digital-to-analog converters for wide-band transmitters

In this thesis, the implementation methods of digital signal processing and digital-to-analog converters for wide-band transmitters are researched. With digital signal processing, the problems of analog signal processing, such as sensitivity to interference and nonidealities of the semiconductor processes, can be avoided. Also, the programmability can be implemented digitally more easily than by means of analog signal processing. During the past few years, wireless communications has evolved from analog to digital, and signal bandwidths have increased, enabling faster and faster data transmission. The evolution of semiconductor processes, decreasing linewidth and supply voltages, has decreased the size of the electronics and power dissipation, enabling the integration of larger and larger systems on single silicon chips. There is little overall benefit in decreasing linewidths to meet the needs of analog design, since it makes the design process more difficult as the device sizes cannot be scaled according to minimum linewidth and because of the decreasing supply voltage. On the other hand, the challenges of digital signal processing are related to the efficient realization of signal processing algorithms in such a way that the required area and power dissipation does not increase extensively. In this book, the problems related to digital filters, upconversion algorithms and digital-to-analog converters used in digital transmitters are researched. Research results are applied to the implementation of a transmitter for a third-generation WCDMA base-station. In addition, the theory of factors affecting the linearity and performance of digital-to-analog converters is researched, and a digital calibration algorithm for enhancement of the static linearity has been presented. The algorithm has been implemented together with a 16-bit converter; its functionality has been demonstrated with measurements.Tässä väitöskirjassa on tutkittu digitaalisen signaalinkäsittelyn toteuttamista ja digitaalisesta analogiseksi -muuntimia laajakaistaisiin lähettimiin. Digitaalisella signaalinkäsittelyllä voidaan välttää monia analogiseen signaalinkäsittelyyn liittyviä ongelmia, kuten häiriöherkkyyttä ja puolijohdeprosessien epäideaalisuuksien vaikutuksia. Myös ohjelmoitavuus on helpommin toteutettavissa digitaalisesti kuin analogisen signaalinkäsittelyn keinoin. Viime vuosina on langattomien tietoliikennejärjestelmien kehitys kulkenut analogisesta digitaaliseen, ja käytettävät signaalikaistanleveydet ovat kasvaneet mahdollistaen yhä nopeamman tiedonsiirron. Puolijohdeprosessien kehitys, kapeneva minimiviivanleveys ja pienemmät käyttöjännitteet, on pienentänyt elektroniikan kokoa ja tehonkulutusta mahdollistaen yhä suurempien kokonaisuuksien integroimisen yhdelle piisirulle. Viivanleveyksien pieneneminen ei kuitenkaan suoraan hyödytä analogiasuunnittelua, jossa piirielementtien kokoa ei välttämättä voida pienentää viivanleveyden pienentyessä, ja jossa madaltuva käyttöjännite ennemminkin hankaloittaa kuin helpottaa suunnittelua. Siksi yhä suurempi osa signaalinkäsittelystä pyritään tekemään digitaalisesti. Digitaalisen signaalinkäsittelyn ongelmat puolestaan liittyvät algoritmien tehokkaaseen toteuttamiseen siten, että piirien pinta-ala ja tehonkulutus eivät kasva liian suuriksi. Tässä kirjassa on tutkittu digitaalisessa lähettimessä tarvittavien digitaalisten suodattimien, ylössekoitusalgoritmien ja digitaalisesta analogiseksi -muuntimien toteuttamiseen liittyviä ongelmia. Tutkimustuloksia on sovellettu kolmannen sukupolven WCDMA-tukiasemalähettimen toteutuksessa. Lisäksi on tutkittu digitaalisesta analogiseksi -muuntimien lineaarisuuteen ja suorituskykyyn vaikuttavien seikkojen teoriaa, ja esitetty digitaalinen kalibrointialgoritmi muuntimen staattisen suorituskyvyn parantamiseksi. Algoritmi on toteutettu 16-bittisen muuntimen yhteydessä ja se on osoitettu toimivaksi mittauksin.reviewe

Design of low OSR, high precision analog-to-digital converters

Advances in electronic systems have lead to the demand for high resolution, high bandwidth Analog-to-Digital Converters (ADCs). Oversampled ADCs are well- known for high accuracy applications since they benefit from noise shaping and they usually do not need highly accurate components. However, as a consequence of oversampling, they have limited signal bandwidth. The signal bandwidth (BW) of oversampled ADCs can be increased either by increasing the sampling rate or reducing the oversampling ratio (OSR). Reducing OSR is a more promising method for increasing the BW, since the sampling speed is usually limited by the technology. The advantageous properties (e.g. low in-band quantization, relaxed accuracy requirements of components) of oversampled ADCs are usually diminished at lower OSRs and preserving these properties requires complicated and power hungry architectures. In this thesis, different combinations of delta-sigma and pipelined ADCs are explored and new techniques for designing oversampled ADCs are proposed. A Hybrid Delta-Sigma/Pipelined (HDSP) ADC is presented. This ADC uses a pipelined ADC as the quantizer of a single-loop delta-sigma modulator and benefits from the aggressive quantization of the pipelined quantizer at low OSRs. A Noise-Shaped Pipelined ADC is proposed which exploits a delta-sigma modulator as the sub-ADC of a pipeline stage to reduce the sensitivity to the analog imperfection. Three prototype ADCs were fabricated in 0.18μm CMOS technology to verify the effectiveness of the proposed techniques. The performance of these architectures is among the best reported for high bandwidth oversampled ADCs.Keywords: Delta-Sigma, Loop Filter, Oversampled ADC, Gain Stage, Pipeline, Noise Shapin

Transmitter architectures with digital modulators, D/A converters and switching-mode power amplifiers

This thesis is composed of nine publications and an overview of the research topic, which also summarises the work. The research described in this thesis focuses on research into the digitalisation of wireless communication base station transmitters. In particular it has three foci: digital modulation, D/A conversion and switching-mode power amplification. The main interest in the implementation of these circuits is in CMOS. The work summarizes the designs of several circuit blocks of a wireless transmitter base station. In the baseband stage, a multicarrier digital modulator that combines multiple modulated signals at different carrier frequencies digitally at baseband, and a multimode digital modulator that can be operated for three different communications standards, are implemented as integrated circuits. The digital modulators include digital power ramping and power level control units for transmission bursts. The upconversion of the baseband signal is implemented using an integrated digital quadrature modulator. The work presented provides insight into the digital-to-analogue interface in the transmitters. This interface is studied both by implementing an intermediate frequency D/A converter in BiCMOS technology and bandpass Delta-Sigma modulator-based D/A conversion in CMOS technology. Finally, the last part of the work discusses switching-mode power amplifiers which are experimented with both as discrete and integrated implementations in conjunction with 1-bit Delta-Sigma modulation and pulse-width modulation as input signal generation methods.Tämä väitöskirja koostuu yhdeksästä julkaisusta ja tutkimusaiheen yhteenvedosta. Väitöskirjassa esitetty tutkimus keskittyy langattaman viestinnän tukiasemien lähettimien digitalisoinnin tutkimukseen. Yksityiskohtaisemmin tutkimusalueet ovat: digitaalinen modulaatio, D/A muunnos ja kytkinmuotoiset tehovahvistimet. Näiden elektronisten piirien toteutuksessa keskitytään CMOS teknologiaan. Työ vetää yhteen useiden langattoman viestinnän tukiasemien lähettimien piirilohkojen suunnittelun. Kantataajuusasteella toteutetaan integroituna piirinä monikantoaaltoinen digitaalinen modulaattori, joka yhdistää useita moduloituja signaaleja eri kantoaalloilla digitaalisesti ja monistandardi digitaalinen modulaatori, joka tukee kolmea eri viestintästandardia. Digitaaliset modulaattoripiirit sisältävät digitaalisen tehoramping ja tehotason säätöyksikön lähetyspurskeita varten. Kantataajuussignaalin ylössekoitus toteutetaan integroitua digitaalista kvadratuurimodulaattoria käyttäen. Esitetty työ antaa näkemystä lähettimien digitalia-analogia rajapintaan, jota tutkitaan toteuttamalla välitaajuinen D/A muunnin BiCMOS teknologialla ja päästökaistainen Delta-Sigma-modulaattoripohjainen D/A muunnin CMOS teknologialla. Lopuksi työn viimeinen osa käsittelee kytkinmuotoisia tehovahvistimia, joita tutkitaan kokeellisesti sekä erilliskompontein toteutettuina piirein että integroiduin piirein toteutettuina käyttäen sisääntulosignaalin muodostamismenetemänä yksibittistä Delta-Sigma-modulaatiota ja pulssin leveys modulaatiota.reviewe

Low Noise, Jitter Tolerant Continuous-Time Sigma-Delta Modulator

The demand for higher data rates in receivers with carrier aggregation (CA) such as LTE, increases the efforts to integrate large number of wireless services into single receiving path, so it needs to digitize the signal in intermediate or high frequencies. It relaxes most of the front-end blocks but makes the design of ADC very challenging. Solving the bottleneck associated with ADC in receiver architecture is a major focus of many ongoing researches. Recently, continuous time Sigma-Delta analog-to-digital converters (ADCs) are getting more attention due to their inherent filtering properties, lower power consumption and wider input bandwidth. But, it suffers from several non-idealities such as clock jitter and ELD which decrease the ADC performance. This dissertation presents two projects that address CT-ΣΔ modulator non-idealities. One of the projects is a CT- ΣΔ modulator with 10.9 Effective Number of Bits (ENOB) with Gradient Descent (GD) based calibration technique. The GD algorithm is used to extract loop gain transfer function coefficients. A quantization noise reduction technique is then employed to improve the Signal to Quantization Noise Ratio (SQNR) of the modulator using a 7-bit embedded quantizer. An analog fast path feedback topology is proposed which uses an analog differentiator in order to compensate excess loop delay. This approach relaxes the requirements of the amplifier placed in front of the quantizer. The modulator is implemented using a third order loop filter with a feed-forward compensation paths and a 3-bit quantizer in the feedback loop. In order to save power and improve loop linearity a two-stage class-AB amplifier is developed. The prototype modulator is implemented in 0.13μm CMOS technology, which achieves peak Signal to Noise and Distortion Ratio (SNDR) of 67.5dB while consuming total power of 8.5-mW under a 1.2V supply with an over sampling ratio of 10 at 300MHz sampling frequency. The prototype achieves Walden's Figure of Merit (FoM) of 146fJ/step. The second project addresses clock jitter non-ideality in Continuous Time Sigma Delta modulators (CT- ΣΔM), the modulator suffer from performance degradation due to uncertainty in timing of clock at digital-to-analog converter (DAC). This thesis proposes to split the loop filter into two parts, analog and digital part to reduce the sensitivity of feedback DAC to clock jitter. By using the digital first-order filter after the quantizer, the effect of clock jitter is reduced without changing signal transfer function (STF). On the other hand, as one pole of the loop filter is implemented digitally, the power and area are reduced by minimizing active analog elements. Moreover, having more digital blocks in the loop of CT- ΣΔM makes it less sensitive to process, voltage, and temperature variations. We also propose the use of a single DAC with a current divider to implement feedback coefficients instead of two DACs to decrease area and clock routing. The prototype is implemented in TSMC 40 nm technology and occupies 0.06 mm^2 area; the proposed solution consumes 6.9 mW, and operates at 500 MS/s. In a 10 MHz bandwidth, the measured dynamic range (DR), peak signal-to-noise-ratio (SNR), and peak signal-to-noise and distortion (SNDR) ratios in presence of 4.5 ps RMS clock jitter (0.22% clock period) are 75 dB, 68 dB, and 67 dB, respectively. The proposed structure is 10 dB more tolerant to clock jitter when compared to the conventional ΣΔM design for similar loop filter

RF DAC

Thesis (Ph. D.)--Massachusetts Institute of Technology, Dept. of Electrical Engineering and Computer Science, 2003.Includes bibliographical references (p. 124-126).Dynamic performance of high speed, high resolution digital-to-analog converters (DACs) is limited by distortion at the data switching instants. Inter-symbol interference (ISI), imperfect timing synchronization and clock jitter are all culprits. A DAC output current controlled by an oscillating waveform is proposed to mitigate the effects of the switching distortion. The oscillating waveform should be a multiple (k*fs) of the sampling frequency (f), where k>l. The waveforms can be aligned so that the data switching occurs in the zero regions of the oscillating output. This makes the DAC insensitive to switch dynamics and jitter. The architecture has the additional benefit of mixing the DAC impulse response energy to a higher frequency. An image of a low IF input signal can therefore be output directly at a high IF or RF frequency for transmit communications applications. A narrow-band sigma-delta DAC with eight unit elements is chosen to demonstrate the radio frequency digital-to-analog converter (RF DAC) concept. A sigma-delta architecture allows the current source transistors to be smaller since mismatch shaping is employed. Smaller current source transistors have a lower drain capacitance, allowing large high frequency output impedance to be achieved without an extra cascode transistor. Elimination of the cascode reduces transistor headroom requirements and allows the DAC to be built with a 1.8V supply. The RF DAC prototype is targeted to GSM transmit specifications and implemented in 0.1 8ptm CMOS technology. Measured single-tone SFDR is -75dBc, SNR is 52dB, and IMD3 is -70.8dBc over a 17.5MHz bandwidth centered at 942.5MHz. Measured SNR has the predicted dependence on the phase alignment of the data clock and oscillating pulse.by Susan Luschas.Ph.D

Linear Operation of Switch-Mode Outphasing Power Amplifiers

Radio transceivers are playing an increasingly important role in modern society. The ”connected” lifestyle has been enabled by modern wireless communications. The demand that has been placed on current wireless and cellular infrastructure requires increased spectral efficiency however this has come at the cost of power efficiency. This work investigates methods of improving wireless transceiver efficiency by enabling more efficient power amplifier architectures, specifically examining the role of switch-mode power amplifiers in macro cell scenarios. Our research focuses on the mechanisms within outphasing power amplifiers which prevent linear amplification. From the analysis it was clear that high power non-linear effects are correctable with currently available techniques however non-linear effects around the zero crossing point are not. As a result signal processing techniques for suppressing and avoiding non-linear operation in low power regions are explored. A novel method of digital pre-distortion is presented, and conventional techniques for linearisation are adapted for the particular needs of the outphasing power amplifier. More unconventional signal processing techniques are presented to aid linearisation of the outphasing power amplifier, both zero crossing and bandwidth expansion reduction methods are designed to avoid operation in nonlinear regions of the amplifiers. In combination with digital pre-distortion the techniques will improve linearisation efforts on outphasing systems with dynamic range and bandwidth constraints respectively. Our collaboration with NXP provided access to a digital outphasing power amplifier, enabling empirical analysis of non-linear behaviour and comparative analysis of behavioural modelling and linearisation efforts. The collaboration resulted in a bench mark for linear wideband operation of a digital outphasing power amplifier. The complimentary linearisation techniques, bandwidth expansion reduction and zero crossing reduction have been evaluated in both simulated and practical outphasing test benches. Initial results are promising and indicate that the benefits they provide are not limited to the outphasing amplifier architecture alone. Overall this thesis presents innovative analysis of the distortion mechanisms of the outphasing power amplifier, highlighting the sensitivity of the system to environmental effects. Practical and novel linearisation techniques are presented, with a focus on enabling wide band operation for modern communications standards