Testing for delay defects utilizing test data compression techniques

textAs technology shrinks new types of defects are being discovered and new fault models are being created for those defects. Transition delay and path delay fault models are two such models that have been created, but they still fall short in that they are unable to obtain a high test coverage of smaller delay defects; these defects can cause functional behavior to fail and also indicate potential reliability issues. The first part of this dissertation addresses these problems by presenting an enhanced timing-based delay fault testing technique that incorporates the use of standard delay ATPG, along with timing information gathered from standard static timing analysis. Utilizing delay fault patterns typically increases the test data volume by 3-5X when compared to stuck-at patterns. Combined with the increase in test data volume associated with the increase in gate count that typically accompanies the miniaturization of technology, this adds up to a very large increase in test data volume that directly affect test time and thus the manufacturing cost. The second part of this dissertation presents a technique for improving test compression and reducing test data volume by using multiple expansion ratios while determining the configuration of the scan chains for each of the expansion ratios using a dependency analysis procedure that accounts for structural dependencies as well as free variable dependencies to improve the probability of detecting faults. Finally, this dissertation addresses the problem of unknown values (X’s) in the output response data corrupting the data and degrading the performance of the output response compactor and thus the overall amount of test compression. Four techniques are presented that focus on handling response data with large percentages of X’s. The first uses X-canceling MISR architecture that is based on deterministically observing scan cells, and the second is a hybrid approach that combines a simple X-masking scheme with the X-canceling MISR for further gains in test compression. The third and fourth techniques revolve around reiterative LFSR X-masking, which take advantage of LFSR-encoded masks that can be reused for multiple scan slices in novel ways.Electrical and Computer Engineerin

REDUCING POWER DURING MANUFACTURING TEST USING DIFFERENT ARCHITECTURES

Power during manufacturing test can be several times higher than power consumption in functional mode. Excessive power during test can cause IR drop, over-heating, and early aging of the chips. In this dissertation, three different architectures have been introduced to reduce test power in general cases as well as in certain scenarios, including field test. In the first architecture, scan chains are divided into several segments. Every segment needs a control bit to enable capture in a segment when new faults are detectable on that segment for that pattern. Otherwise, the segment should be disabled to reduce capture power. We group the control bits together into one or more control chains. To address the extra pin(s) required to shift data into the control chain(s) and significant post processing in the first architecture, we explored a second architecture. The second architecture stitches the control bits into the chains they control as EECBs (embedded enable capture bits) in between the segments. This allows an ATPG software tool to automatically generate the appropriate EECB values for each pattern to maintain the fault coverage. This also works in the presence of an on-chip decompressor. The last architecture focuses primarily on the self-test of a device in a 3D stacked IC when an existing FPGA in the stack can be programmed as a tester. We show that the energy expended during test is significantly less than would be required using low power patterns fed by an on-chip decompressor for the same very short scan chains

A comprehensive comparison between design for testability techniques for total dose testing of flash-based FPGAs

Radiation sources exist in different kinds of environments where electronic devices often operate. Correct device operation is usually affected negatively by radiation. The radiation resultant effect manifests in several forms depending on the operating environment of the device like total ionizing dose effect (TID), or single event effects (SEEs) such as single event upset (SEU), single event gate rupture (SEGR), and single event latch up (SEL). CMOS circuits and Floating gate MOS circuits suffer from an increase in the delay and the leakage current due to TID effect. This may damage the proper operation of the integrated circuit. Exhaustive testing is needed for devices operating in harsh conditions like space and military applications to ensure correct operations in the worst circumstances. The use of worst case test vectors (WCTVs) for testing is strongly recommended by MIL-STD-883, method 1019, which is the standard describing the procedure for testing electronic devices under radiation. However, the difficulty of generating these test vectors hinders their use in radiation testing. Testing digital circuits in the industry is usually done nowadays using design for testability (DFT) techniques as they are very mature and can be relied on. DFT techniques include, but not limited to, ad-hoc technique, built-in self test (BIST), muxed D scan, clocked scan and enhanced scan. DFT is usually used with automatic test patterns generation (ATPG) software to generate test vectors to test application specific integrated circuits (ASICs), especially with sequential circuits, against faults like stuck at faults and path delay faults. Despite all these recommendations for DFT, radiation testing has not benefited from this reliable technology yet. Also, with the big variation in the DFT techniques, choosing the right technique is the bottleneck to achieve the best results for TID testing. In this thesis, a comprehensive comparison between different DFT techniques for TID testing of flash-based FPGAs is made to help designers choose the best suitable DFT technique depending on their application. The comparison includes muxed D scan technique, clocked scan technique and enhanced scan technique. The comparison is done using ISCAS-89 benchmarks circuits. Points of comparisons include FPGA resources utilization, difficulty of designs bring-up, added delay by DFT logic and robust testable paths in each technique

Identifying worst case test vectors for FPGA exposed to total ionization dose using design for testability techniques

Electronic devices often operate in harsh environments which contain a variation of radiation sources. Radiation may cause different kinds of damage to proper operation of the devices. Their sources can be found in terrestrial environments, or in extra-terrestrial environments like in space, or in man-made radiation sources like nuclear reactors, biomedical devices and high energy particles physics experiments equipment. Depending on the operation environment of the device, the radiation resultant effect manifests in several forms like total ionizing dose effect (TID), or single event effects (SEEs) such as single event upset (SEU), single event gate rupture (SEGR), and single event latch up (SEL). TID effect causes an increase in the delay and the leakage current of CMOS circuits which may damage the proper operation of the integrated circuit. To ensure proper operation of these devices under radiation, thorough testing must be made especially in critical applications like space and military applications. Although the standard which describes the procedure for testing electronic devices under radiation emphasizes the use of worst case test vectors (WCTVs), they are never used in radiation testing due to the difficulty of generating these vectors for circuits under test. For decades, design for testability (DFT) has been the best choice for test engineers to test digital circuits in industry. It has become a very mature technology that can be relied on. DFT is usually used with automatic test patterns generation (ATPG) software to generate test vectors to test application specific integrated circuits (ASICs), especially with sequential circuits, against faults like stuck at faults and path delay faults. Surprisingly, however, radiation testing has not yet made use of this reliable technology. In this thesis, a novel methodology is proposed to extend the usage of DFT to generate WCTVs for delay failure in Flash based field programmable gate arrays (FPGAs) exposed to total ionizing dose (TID). The methodology is validated using MicroSemi ProASIC3 FPGA and cobalt 60 facility

Improving timing verification and delay testing methodologies for IC designs

textThe task of ensuring the correct temporal behavior of IC designs, both before and after fabrication, is extremely important. It is becoming even more imperative as the demand for performance increases and process technology advances into the deep sub-micron region. This dissertation tackles the key issues in the timing verification and delay testing methodologies. An efficient methodology is presented to identify false timing paths in the timing verification methodology which utilizes ATPG technique and timing information from an ordered list of timing paths according to the delay information. This dissertation also presents a speed binning methodology which utilizes structural delay tests successfully instead of functional tests. In addition, it establishes a methodology which quantifies the correlation between the timing verification prediction and actual silicon measurement of timing paths. This quantification methodology lays the foundation for further research to study the impact of deep submicron effects on design performanceElectrical and Computer Engineerin

Algorithms for Power Aware Testing of Nanometer Digital ICs

At-speed testing of deep-submicron digital very large scale integrated (VLSI) circuits has become mandatory to catch small delay defects. Now, due to continuous shrinking of complementary metal oxide semiconductor (CMOS) transistor feature size, power density grows geometrically with technology scaling. Additionally, power dissipation inside a digital circuit during the testing phase (for test vectors under all fault models (Potluri, 2015)) is several times higher than its power dissipation during the normal functional phase of operation. Due to this, the currents that flow in the power grid during the testing phase, are much higher than what the power grid is designed for (the functional phase of operation). As a result, during at-speed testing, the supply grid experiences unacceptable supply IR-drop, ultimately leading to delay failures during at-speed testing. Since these failures are specific to testing and do not occur during functional phase of operation of the chip, these failures are usually referred to false failures, and they reduce the yield of the chip, which is undesirable. In nanometer regime, process parameter variations has become a major problem. Due to the variation in signalling delays caused by these variations, it is important to perform at-speed testing even for stuck faults, to reduce the test escapes (McCluskey and Tseng, 2000; Vorisek et al., 2004). In this context, the problem of excessive peak power dissipation causing false failures, that was addressed previously in the context of at-speed transition fault testing (Saxena et al., 2003; Devanathan et al., 2007a,b,c), also becomes prominent in the context of at-speed testing of stuck faults (Maxwell et al., 1996; McCluskey and Tseng, 2000; Vorisek et al., 2004; Prabhu and Abraham, 2012; Potluri, 2015; Potluri et al., 2015). It is well known that excessive supply IR-drop during at-speed testing can be kept under control by minimizing switching activity during testing (Saxena et al., 2003). There is a rich collection of techniques proposed in the past for reduction of peak switching activity during at-speed testing of transition/delay faults ii in both combinational and sequential circuits. As far as at-speed testing of stuck faults are concerned, while there were some techniques proposed in the past for combinational circuits (Girard et al., 1998; Dabholkar et al., 1998), there are no techniques concerning the same for sequential circuits. This thesis addresses this open problem. We propose algorithms for minimization of peak switching activity during at-speed testing of stuck faults in sequential digital circuits under the combinational state preservation scan (CSP-scan) architecture (Potluri, 2015; Potluri et al., 2015). First, we show that, under this CSP-scan architecture, when the test set is completely specified, the peak switching activity during testing can be minimized by solving the Bottleneck Traveling Salesman Problem (BTSP). This mapping of peak test switching activity minimization problem to BTSP is novel, and proposed for the first time in the literature. Usually, as circuit size increases, the percentage of don’t cares in the test set increases. As a result, test vector ordering for any arbitrary filling of don’t care bits is insufficient for producing effective reduction in switching activity during testing of large circuits. Since don’t cares dominate the test sets for larger circuits, don’t care filling plays a crucial role in reducing switching activity during testing. Taking this into consideration, we propose an algorithm, XStat, which is capable of performing test vector ordering while preserving don’t care bits in the test vectors, following which, the don’t cares are filled in an intelligent fashion for minimizing input switching activity, which effectively minimizes switching activity inside the circuit (Girard et al., 1998). Through empirical validation on benchmark circuits, we show that XStat minimizes peak switching activity significantly, during testing. Although XStat is a very powerful heuristic for minimizing peak input-switchingactivity, it will not guarantee optimality. To address this issue, we propose an algorithm that uses Dynamic Programming to calculate the lower bound for a given sequence of test vectors, and subsequently uses a greedy strategy for filling don’t cares in this sequence to achieve this lower bound, thereby guaranteeing optimality. This algorithm, which we refer to as DP-fill in this thesis, provides the globally optimal solution for minimizing peak input-switching-activity and also is the best known in the literature for minimizing peak input-switching-activity during testing. The proof of optimality of DP-fill in minimizing peak input-switching-activity is also provided in this thesis

Enhancement and validation of a test technique for integrated circuits

This thesis focuses on a scan-based delay testing technique that was recently developed at ETS. This new approach, called Captureless Delay Testing (CDT), has been proposed as a technique that complements traditional methods of test, ensuring the integrated circuits will function at their proposed clock speed, further improving the test coverage of the particular type of test. Furthermore, CDT incorporates the use of sensors enabling the detection of the presence of transitions at strategic locations. The purpose of this project is to improve on certain aspects of this novel technique. At first, we analyze the delay distribution of the non-covered nodes by traditional methods of test, in order to develop the best way possible of placement of the CDT sensors. We present, using Perl Language, the ensemble of tools developed for this purpose. The end results obtained confirm that the paths that pass through the non-covered nodes are longer than those that traverse the covered ones. The difference between the two types of paths exceeds 20%) of the clock period when considering the shorter path delay values. Secondly, we propose a fially automated algorithm that enables, at the earliest stages of the test vectors generation process: 1) the identification of the non-covered nodes, 2) the identification of the placements of the CDT sensors at the inputs of the flip-flops for further improvement of the test coverage, and 3) the minimization of the number of sensors with regards to requirements. Our results indicate that when we apply CDT on top of transitionbased fault model we can improve the test coverage by 5%. Moreover, the algorithm of CDT sensors minimization allows a reduction of more than 85% the number of those sensors with a minimal test coverage loss, on average of 1.6%

Low-Capture-Power Test Generation for Scan-Based At-Speed Testing

Scan-based at-speed testing is a key technology to guarantee timing-related test quality in the deep submicron era. However, its applicability is being severely challenged since significant yield loss may occur from circuit malfunction due to excessive IR drop caused by high power dissipation when a test response is captured. This paper addresses this critical problem with a novel low-capture-power X-filling method of assigning 0\u27s and 1\u27s to unspecified (X) bits in a test cube obtained during ATPG. This method reduces the circuit switching activity in capture mode and can be easily incorporated into any test generation flow to achieve capture power reduction without any area, timing, or fault coverage impact. Test vectors generated with this practical method greatly improve the applicability of scan-based at-speed testing by reducing the risk of test yield lossIEEE International Conference on Test, 2005, 8 November 2005, Austin, TX, US

Heuristics Based Test Overhead Reduction Techniques in VLSI Circuits

The electronic industry has evolved at a mindboggling pace over the last five decades. Moore’s Law [1] has enabled the chip makers to push the limits of the physics to shrink the feature sizes on Silicon (Si) wafers over the years. A constant push for power-performance-area (PPA) optimization has driven the higher transistor density trends. The defect density in advanced process nodes has posed a challenge in achieving sustainable yield. Maintaining a low Defect-per-Million (DPM) target for a product to be viable with stringent Time-to-Market (TTM) has become one of the most important aspects of the chip manufacturing process. Design-for-Test (DFT) plays an instrumental role in enabling low DPM. DFT however impacts the PPA of a chip. This research describes an approach of minimizing the scan test overhead in a chip based on circuit topology heuristics. These heuristics are applied on a full-scan design to convert a subset of the scan flip-flops (SFF) into D flip-flops (DFF). The K Longest Path per Gate (KLPG) [2] automatic test pattern generation (ATPG) algorithm is used to generate tests for robust paths in the circuit. Observability driven multi cycle path generation [3][4] and test are used in this work to minimize coverage loss caused by the SFF conversion process. The presence of memory arrays in a design exacerbates the coverage loss due to the shadow cast by the array on its neighboring logic. A specialized behavioral modeling for the memory array is required to enable test coverage of the shadow logic. This work develops a memory model integrated into the ATPG engine for this purpose. Multiple clock domains pose challenges in the path generation process. The inter-domain clocking relationship and corresponding logic sensitization are modeled in our work to generate synchronous inter-domain paths over multiple clock cycles. Results are demonstrated on ISCAS89 and ITC99 benchmark circuits. Power saving benefit is quantified using an open-source standard-cell library