5,839 research outputs found
Continuous time controller based on SMC and disturbance observer for piezoelectric actuators
Abstract – In this work, analog application for the Sliding Mode Control (SMC) to piezoelectric actuators (PEA) is presented. DSP application of the algorithm suffers from ADC and DAC conversions and mainly faces limitations in sampling time interval. Moreover piezoelectric actuators are known to have very large bandwidth close to the DSP operation frequency. Therefore, with the direct analog application, improvement of the performance and high frequency operation are expected. Design of an appropriate SMC together with a disturbance observer is suggested to have continuous control output and related experimental results for position tracking are presented with comparison of DSP and analog control application
A Sliding Mode Control for a Sensorless Tracker: Application on a Photovoltaic System
The photovoltaic sun tracker allows us to increase the energy production. The
sun tracker considered in this study has two degrees of freedom (2-DOF) and
especially specified by the lack of sensors. In this way, the tracker will have
as a set point the sun position at every second during the day for a period of
five years. After sunset, the tracker goes back to the initial position (which
of sunrise). The sliding mode control (SMC) will be applied to ensure at best
the tracking mechanism and, in another hand, the sliding mode observer will
replace the velocity sensor which suffers from a lot of measurement
disturbances. Experimental measurements show that this autonomic dual axis Sun
Tracker increases the power production by over 40%
A Sliding Mode Multimodel Control for a Sensorless Photovoltaic System
In this work we will talk about a new control test using the sliding mode
control with a nonlinear sliding mode observer, which are very solicited in
tracking problems, for a sensorless photovoltaic panel. In this case, the panel
system will has as a set point the sun position at every second during the day
for a period of five years; then the tracker, using sliding mode multimodel
controller and a sliding mode observer, will track these positions to make the
sunrays orthogonal to the photovoltaic cell that produces more energy. After
sunset, the tracker goes back to the initial position (which of sunrise).
Experimental measurements show that this autonomic dual axis Sun Tracker
increases the power production by over 40%
Optimal control design for robust fuzzy friction compensation in a robot joint
This paper presents a methodology for the compensation of nonlinear friction in a robot joint structure based on a fuzzy local modeling technique. To enhance the tracking performance of the robot joint, a dynamic model is derived from the local physical properties of friction. The model is the basis of a precompensator taking into account the dynamics of the overall corrected system by means of a minor loop. The proposed structure does not claim to faithfully reproduce complex phenomena driven by friction. However, the linearity of the local models simplifies the design and implementation of the observer, and its estimation capabilities are improved by the nonlinear integral gain. The controller can then be robustly synthesized using linear matrix inequalities to cancel the effects of inexact friction compensation. Experimental tests conducted on a robot joint with a high level of friction demonstrate the effectiveness of the proposed fuzzy observer-based control strategy for tracking system trajectories when operating in zero-velocity regions and during motion reversals
MODELING, ANALYSIS AND CONTROL OF FLEXIBLE SOLID-STATE HYSTERETIC ACTUATORS
A distributed parameters modeling and control framework for flexible solid-state hysteretic actuator is presented in this work. For the simplicity of analysis, the actuator dynamic behavior is decoupled and treated separately from the hysteresis nonlinearity. To include the effects of widely-used flexural mechanisms, a mass-spring-damper boundary condition is considered for system. Moreover, the effect of electromechanical actuation is included as a concentrate force at the boundary. The problem is then divided into two parts: first part deals with free motion analysis of system in order to obtain eigenvalues and eigenfunctions using the expansion theorem and a standard eigenvalue problem procedure. The effects of different boundary mass and spring values on the natural frequencies and mode shapes are demonstrated, which indicate their significant contribution to system performance. In the second part, forced motion analysis of system and its state-space representation are presented. A frequency based control strategy utilizing widely used Lyapunov theorem is designed to obtain an accurate control over the actuator motion. A robust variable structure control is incorporated into the developed controller for compensation of ever-present plant structural uncertainties. A full order state feedback observer is designed to accurately mimic the states of an unobservable plant. An optimization algorithm is developed to compute the optimal observer gain matrix. Various frequency tracking simulations are performed using feedback controller-observer model to observe the effect of modes deficiency on the tracking frequency bandwidth of the controller. Finally, for the accurate prediction of nonlinear multi-loop hysteresis effect, a major source of inaccuracies at quasi-static frequency, a recently developed hysteresis model based on three hysteric properties of piezoelectric material namely targeting of turning points, curve alignment and the wiping-out effect is used. Initially, the hysteresis nonlinearity is decoupled from the looping effect and modeled separately using an exponential function. The obtained exponential function is then utilized in a nonlinear mapping procedure, where it is mapped between consequent turning points recorded in model memory unit. This mapping also uses four constant shaping parameters - two for the ascending and two for the descending hysteresis trajectories. A proportional integral (PI) controller is used for the compensation of hysteresis nonlinearity. Performance of PI controller is validated using several numerical simulations. Finally, the method of combining robust feedback control strategy with the feedforward hysteresis compensation technique is presented to accomplish the precise control over actuator motion
Global fast non-singular terminal sliding-mode control for high-speed nanopositioning
Peer reviewedPostprin
Recommended from our members
High performance disturbance observer based control system design for permanent magnet synchronous AC machine applications
This thesis was submitted for the award of Doctor of Philosophy and was awarded by Brunel University LondonAn electrical machine is one of the main workforces in different industries and serves them in various applications. Machine drive control design involves many technical issues for efficient and robust exploitation. Over several decades, Permanent Magnet Synchronous Motor (PMSM) is getting preferred for industrial applications over its counterpart Squirrel Cage Induction Motor (SCIM) drive, because of their higher efficiency, power density, and higher torque to inertia ratio.
In the prospective that PMSM drives are considered the drives of the future, there are still technical challenges and issues related to PMSM control. Many studies have been devoted to PMSM control in the past, but there are still some open research areas that bring worldwide researchers’ interests back to PMSM drive control. One of the approaches that may facilitate better performance, higher efficiency, and robust and reliable work of the control system is the disturbance observer-based control (DOBC) with linear and nonlinear output feedback control for PM synchronous machine applications. DOBC is adopted due to its ability to reject external and internal disturbances with improving tracking performance in the variable speed wind energy conversion system (WECS) to maximize power extraction. The high order disturbance observer (HODO) is utilized to estimate the aerodynamic torque-based wind speed without the use of a traditional anemometer, which reduces the overall cost and improves the reliability of the whole system. Also, this method has been designed to improve the angular shaft speed tracking of the PMSM system under load torque disturbance and speed variations.
The model-based linear and nonlinear feedback control are used in the proposed control systems. The sliding mode control (SMC) with switching output feedback control law and integral SMC with linear feedback and state-dependent Riccati equation (SDRE) based approaches have been designed for the systems. The SDRE control accounts for the nonlinear multivariable structure of the WECS and is approximated with Taylor series expansion terms. The chattering inherited from SMC is eliminated by the continuous approximation technique. The sliding mode is guaranteed by eliminating the reaching mode in the proposed integral SMC. The model-free cascaded linear feedback control system based on the proportional-integral (PI) controllers use a back-calculation algorithm anti-windup scheme. The proposed speed controllers are synthesized with HODO to compensate for the external disturbance, model uncertainty, noise, and modelling errors. Moreover, servomechanism-based SDRE control, a near-optimal control system is designed to suppress the model uncertainty and noise without the use of disturbance observers.
The proposed control systems for PMSM speed regulation have demonstrated a significant improvement in the angular shaft speed-tracking performance at the transients. Their performances have been tested under speed, load torque variations, and model uncertainty. For example, HODO-based SMC with switching output feedback control law (SOFCL) has demonstrated improvement by more than 78% than the PI-PI control system of the PMSM. The performance of the HODOs-based Integral SMC with SDRE nonlinear feedback is improved by 80.5% under external disturbance, model uncertainty, and noise than Integral SMC with linear feedback in the WECS. The HODO-based SDRE control with servomechanism has shown an 80.2% improvement of mean absolute percentage error under disturbances than Integral SMC with linear feedback in the WECS. The PMSM speed tracking performance of the proposed HODO-based discrete-time PI-PI control system with back-calculation algorithm anti-windup scheme is improved by 87.29% and 90.2% in the speed commands and load torque disturbance variations scenarios respectively. The simulations for testing the proposed control system of the PMSM system and WECS have been implemented in Matlab/Simulink environment. The PMSM speed control experimental results have been obtained with Lucas-Nuelle DSP-based rapid control prototyping kit.Center for International Program “Bolashak” of the Ministry of Education and Science Republic of Kazakhsta
- …