1,156 research outputs found
Signal and System Design for Wireless Power Transfer : Prototype, Experiment and Validation
A new line of research on communications and signals design for Wireless
Power Transfer (WPT) has recently emerged in the communication literature.
Promising signal strategies to maximize the power transfer efficiency of WPT
rely on (energy) beamforming, waveform, modulation and transmit diversity, and
a combination thereof. To a great extent, the study of those strategies has so
far been limited to theoretical performance analysis. In this paper, we study
the real over-the-air performance of all the aforementioned signal strategies
for WPT. To that end, we have designed, prototyped and experimented an
innovative radiative WPT architecture based on Software-Defined Radio (SDR)
that can operate in open-loop and closed-loop (with channel acquisition at the
transmitter) modes. The prototype consists of three important blocks, namely
the channel estimator, the signal generator, and the energy harvester. The
experiments have been conducted in a variety of deployments, including
frequency flat and frequency selective channels, under static and mobility
conditions. Experiments highlight that a channeladaptive WPT architecture based
on joint beamforming and waveform design offers significant performance
improvements in harvested DC power over conventional
single-antenna/multiantenna continuous wave systems. The experimental results
fully validate the observations predicted from the theoretical signal designs
and confirm the crucial and beneficial role played by the energy harvester
nonlinearity.Comment: Accepted to IEEE Transactions on Wireless Communication
Recommended from our members
Measurements, processing functions and laboratory test-bed experiments for evaluating diversity in broadcast network
This paper presents a test-bed development and measurement plan for evaluating transmit diversity and on-channel repeaters in the Digital Video Broadcasting Network. Transmit diversity reduces the complexity and improves the power consumption of the personal receiving devices by enhancing the transmission of signals in NLOS cluttered environments. It is more practical than receive diversity due to the difficulty of locating two receive antennas far enough apart in a small mobile device. The on-channel repeater is to extend the coverage of the DVB-T/H network in areas where services are inaccessible by receiving the DVB-T/H signals off air, amplifying and then retransmitting it on the same frequency as received. Test service scenarios were developed to illustrate the benefits of such technologies so that effectiveness can be researched in a variety of service and terrain scenarios using purpose built test systems.The work presented in this paper was supported by the European Commission IST project PLUTO
Wireless industrial monitoring and control networks: the journey so far and the road ahead
While traditional wired communication technologies have played a crucial role in industrial monitoring and control networks over the past few decades, they are increasingly proving to be inadequate to meet the highly dynamic and stringent demands of today’s industrial applications, primarily due to the very rigid nature of wired infrastructures. Wireless technology, however, through its increased pervasiveness, has the potential to revolutionize the industry, not only by mitigating the problems faced by wired solutions, but also by introducing a completely new class of applications. While present day wireless technologies made some preliminary inroads in the monitoring domain, they still have severe limitations especially when real-time, reliable distributed control operations are concerned. This article provides the reader with an overview of existing wireless technologies commonly used in the monitoring and control industry. It highlights the pros and cons of each technology and assesses the degree to which each technology is able to meet the stringent demands of industrial monitoring and control networks. Additionally, it summarizes mechanisms proposed by academia, especially serving critical applications by addressing the real-time and reliability requirements of industrial process automation. The article also describes certain key research problems from the physical layer communication for sensor networks and the wireless networking perspective that have yet to be addressed to allow the successful use of wireless technologies in industrial monitoring and control networks
Opportunistic Access in Frequency Hopping Cognitive Radio Networks
Researchers in the area of cognitive radio often investigate the utility of dynamic spectrum access as a means to make more efficient use of the radio frequency spectrum. Many studies have been conducted to find ways in which a secondary user can occupy spectrum licensed to a primary user in a manner which does not disrupt the primary user\u27s performance. This research investigates the use of opportunistic access in a frequency hopping radio to mitigate the interference caused by other transmitters in a contentious environment such as the unlicensed 2.4 GHz region. Additionally, this work demonstrates how dynamic spectrum access techniques can be used not only to prevent interfering with other users but also improve the robustness of a communication system
Measurement and Optimization of LTE Performance
4G Long Term Evolution (LTE) mobile system is the fourth generation communication system adopted worldwide to provide high-speed data connections and high-quality voice calls. Given the recent deployment by mobile service providers, unlike GSM and UMTS, LTE can be still considered to be in its early stages and therefore many topics still raise great interest among the international scientific research community: network performance assessment, network optimization, selective scheduling, interference management and coexistence with other communication systems in the unlicensed band, methods to evaluate human exposure to electromagnetic radiation are, as a matter of fact, still open issues.
In this work techniques adopted to increase LTE radio performances are investigated. One of the most wide-spread solutions proposed by the standard is to implement MIMO techniques and within a few years, to overcome the scarcity of spectrum, LTE network operators will offload data traffic by accessing the unlicensed 5 GHz frequency. Our Research deals with an evaluation of 3GPP standard in a real test best scenario to evaluate network behavior and performance
Efficient DSP and Circuit Architectures for Massive MIMO: State-of-the-Art and Future Directions
Massive MIMO is a compelling wireless access concept that relies on the use
of an excess number of base-station antennas, relative to the number of active
terminals. This technology is a main component of 5G New Radio (NR) and
addresses all important requirements of future wireless standards: a great
capacity increase, the support of many simultaneous users, and improvement in
energy efficiency. Massive MIMO requires the simultaneous processing of signals
from many antenna chains, and computational operations on large matrices. The
complexity of the digital processing has been viewed as a fundamental obstacle
to the feasibility of Massive MIMO in the past. Recent advances on
system-algorithm-hardware co-design have led to extremely energy-efficient
implementations. These exploit opportunities in deeply-scaled silicon
technologies and perform partly distributed processing to cope with the
bottlenecks encountered in the interconnection of many signals. For example,
prototype ASIC implementations have demonstrated zero-forcing precoding in real
time at a 55 mW power consumption (20 MHz bandwidth, 128 antennas, multiplexing
of 8 terminals). Coarse and even error-prone digital processing in the antenna
paths permits a reduction of consumption with a factor of 2 to 5. This article
summarizes the fundamental technical contributions to efficient digital signal
processing for Massive MIMO. The opportunities and constraints on operating on
low-complexity RF and analog hardware chains are clarified. It illustrates how
terminals can benefit from improved energy efficiency. The status of technology
and real-life prototypes discussed. Open challenges and directions for future
research are suggested.Comment: submitted to IEEE transactions on signal processin
Spectrum Sharing, Latency, and Security in 5G Networks with Application to IoT and Smart Grid
The surge of mobile devices, such as smartphones, and tables, demands additional capacity. On the other hand, Internet-of-Things (IoT) and smart grid, which connects numerous sensors, devices, and machines require ubiquitous connectivity and data security. Additionally, some use cases, such as automated manufacturing process, automated transportation, and smart grid, require latency as low as 1 ms, and reliability as high as 99.99\%. To enhance throughput and support massive connectivity, sharing of the unlicensed spectrum (3.5 GHz, 5GHz, and mmWave) is a potential solution. On the other hand, to address the latency, drastic changes in the network architecture is required. The fifth generation (5G) cellular networks will embrace the spectrum sharing and network architecture modifications to address the throughput enhancement, massive connectivity, and low latency.
To utilize the unlicensed spectrum, we propose a fixed duty cycle based coexistence of LTE and WiFi, in which the duty cycle of LTE transmission can be adjusted based on the amount of data. In the second approach, a multi-arm bandit learning based coexistence of LTE and WiFi has been developed. The duty cycle of transmission and downlink power are adapted through the exploration and exploitation. This approach improves the aggregated capacity by 33\%, along with cell edge and energy efficiency enhancement. We also investigate the performance of LTE and ZigBee coexistence using smart grid as a scenario.
In case of low latency, we summarize the existing works into three domains in the context of 5G networks: core, radio and caching networks. Along with this, fundamental constraints for achieving low latency are identified followed by a general overview of exemplary 5G networks. Besides that, a loop-free, low latency and local-decision based routing protocol is derived in the context of smart grid. This approach ensures low latency and reliable data communication for stationary devices.
To address data security in wireless communication, we introduce a geo-location based data encryption, along with node authentication by k-nearest neighbor algorithm. In the second approach, node authentication by the support vector machine, along with public-private key management, is proposed. Both approaches ensure data security without increasing the packet overhead compared to the existing approaches
- …