Study of continuous-phase four-state modulation for cordless telecommunications. Assessment by simulation of CP-QFSK as an alternative modulation scheme for TDMA digital cordless telecommunications systems operating in indoor applications

One of the major driving elements behind the explosive boom in wireless revolution is the advances in the field of modulation which plays a fundamental role in any communication system, and especially in cellular radio systems. Hence, the elaborate choice of an efficient modulation scheme is of paramount importance in the design and employment of any communications system. Work presented in this thesis is an investigation (study) of the feasibility of whether multilevel FSK modulation scheme would provide a viable alternative modem that can be employed in TDMA cordless communications systems. In the thesis the design and performance analysis of a non-coherent multi-level modem that offers a great deal of bandwidth efficiency and hardware simplicity is studied in detail. Simulation results demonstrate that 2RC pre-modulation filter pulse shaping with a modulation index of 0.3, and pre-detection filter normalized equivalent noise bandwidth of 1.5 are optimum system parameter values. Results reported in chapter 5 signify that an adjacent channel rejection factor of around 40 dB has been achieved at channel spacing of 1.5 times the symbol rate while the DECT system standards stipulated a much lower rejection limit criterion (25-30dB), implying that CP-QFSK modulation out-performs the conventional GMSK as it causes significantly less ACI, thus it is more spectrally efficient in a multi-channel system. However, measured system performance in terms of BER indicates that this system does not coexist well with other interferers as at delay spreads between 100ns to 200ns, which are commonly encountered in such indoor environment, a severe degradation in system performance apparently caused by multi-path fading has been noticed, and there exists a noise floor of about 40 dB, i.e. high irreducible error rate of less than 5.10-3. Implementing MRC diversity combiner and BCH codec has brought in a good gain.Higher Education Ministr

Convergence of packet communications over the evolved mobile networks; signal processing and protocol performance

In this thesis, the convergence of packet communications over the evolved mobile networks is studied. The Long Term Evolution (LTE) process is dominating the Third Generation Partnership Project (3GPP) in order to bring technologies to the markets in the spirit of continuous innovation. The global markets of mobile information services are growing towards the Mobile Information Society. The thesis begins with the principles and theories of the multiple-access transmission schemes, transmitter receiver techniques and signal processing algorithms. Next, packet communications and Internet protocols are referred from the IETF standards with the characteristics of mobile communications in the focus. The mobile network architecture and protocols bind together the evolved packet system of Internet communications to the radio access network technologies. Specifics of the traffic models are shortly visited for their statistical meaning in the radio performance analysis. Radio resource management algorithms and protocols, also procedures, are covered addressing their relevance for the system performance. Throughout these Chapters, the commonalities and differentiators of the WCDMA, WCDMA/HSPA and LTE are covered. The main outcome of the thesis is the performance analysis of the LTE technology beginning from the early discoveries to the analysis of various system features and finally converging to an extensive system analysis campaign. The system performance is analysed with the characteristics of voice over the Internet and best effort traffic of the Internet. These traffic classes represent the majority of the mobile traffic in the converged packet networks, and yet they are simple enough for a fair and generic analysis of technologies. The thesis consists of publications and inventions created by the author that proposed several improvements to the 3G technologies towards the LTE. In the system analysis, the LTE showed by the factor of at least 2.5 to 3 times higher system measures compared to the WCDMA/HSPA reference. The WCDMA/HSPA networks are currently available with over 400 million subscribers and showing increasing growth, in the meanwhile the first LTE roll-outs are scheduled to begin in 2010. Sophisticated 3G LTE mobile devices are expected to appear fluently for all consumer segments in the following years

RF Power Amplifier and Its Envelope Tracking

This dissertation introduces an agile supply modulator with optimal transient performance for the envelope tracking supply in linear power amplifiers. For this purpose, an on-demand current source module, the bang-bang transient performance enhancer (BBTPE), is proposed. Its objective is to follow fast variations in input signals with reduced overshoot and settling time without deteriorating the steady-state performance of the buck regulator. The proposed approach enables fast system response through the BBTPE and an accurate steady-state output response through a low switching ripple and power efficient dynamic buck regulator. Fast output response with the help of the added module induces a slower rise of inductor current in the buck converter that further assists the proposed system to reduce both overshoot and settling time. To demonstrate the feasibility of the proposed solution, extensive simulations and experimental results from a discrete system are reported. The proposed supply modulator shows 80% improvement in rise time along with 60% reduction in both overshoot and settling time compared to the conventional dynamic buck regulator-based solution. Experimental results for a PA using the LTE 16-QAM 5 MHz standard shows improvement of 7.68 dB and 65.1% in ACPR and EVM, respectively. In a polar power amplifier, the input signal splits into phase and amplitude components using a non-linear conversion operation. This operation broadens the spectrum of the polar signal components. The information of amplitude and phase contains spectral images due to the sampling operation in non-linear conversion operation. These spectral images can be large and cause out-of-band emission in the output spectrum. In addition, during the recombination process of phase and amplitude, a delay mismatch between amplitude and phase signals, which can occur due to separate processing paths of amplitude and phase signals, causes out-of-band emissions, also known as spectral regrowth. This dissertation presents solutions to both of the issues of digital polar power amplifier: spectral images and delay mismatch. In order to reduce the problem of spectral images, interpolation of phase and amplitude is proposed in this work. This increases the effective sampling frequency of the amplitude and phase, which helps to improve the linearity by around 10 dB. In addition, a novel calibration scheme is proposed here for the delay mismatch between phase and amplitude path in a digital polar power amplifier. The scheme significantly reduces the spectral regrowth. The scheme uses the same path for phase and amplitude delay calculation after the recombination that allows having a robust calibration. Furthermore, it can be executed during the empty transmission slots. The proposed scheme is designed in a 40 nm CMOS technology and simulated with a 64-QAM IEEE 802.11n wireless standard. The scheme achieved 7.57 dB enhancement in ACLR and 84.35% improvement in EVM for a 3.5 ns mismatch in phase and amplitude path

RF Power Amplifier and Its Envelope Tracking

This dissertation introduces an agile supply modulator with optimal transient performance for the envelope tracking supply in linear power amplifiers. For this purpose, an on-demand current source module, the bang-bang transient performance enhancer (BBTPE), is proposed. Its objective is to follow fast variations in input signals with reduced overshoot and settling time without deteriorating the steady-state performance of the buck regulator. The proposed approach enables fast system response through the BBTPE and an accurate steady-state output response through a low switching ripple and power efficient dynamic buck regulator. Fast output response with the help of the added module induces a slower rise of inductor current in the buck converter that further assists the proposed system to reduce both overshoot and settling time. To demonstrate the feasibility of the proposed solution, extensive simulations and experimental results from a discrete system are reported. The proposed supply modulator shows 80% improvement in rise time along with 60% reduction in both overshoot and settling time compared to the conventional dynamic buck regulator-based solution. Experimental results for a PA using the LTE 16-QAM 5 MHz standard shows improvement of 7.68 dB and 65.1% in ACPR and EVM, respectively. In a polar power amplifier, the input signal splits into phase and amplitude components using a non-linear conversion operation. This operation broadens the spectrum of the polar signal components. The information of amplitude and phase contains spectral images due to the sampling operation in non-linear conversion operation. These spectral images can be large and cause out-of-band emission in the output spectrum. In addition, during the recombination process of phase and amplitude, a delay mismatch between amplitude and phase signals, which can occur due to separate processing paths of amplitude and phase signals, causes out-of-band emissions, also known as spectral regrowth. This dissertation presents solutions to both of the issues of digital polar power amplifier: spectral images and delay mismatch. In order to reduce the problem of spectral images, interpolation of phase and amplitude is proposed in this work. This increases the effective sampling frequency of the amplitude and phase, which helps to improve the linearity by around 10 dB. In addition, a novel calibration scheme is proposed here for the delay mismatch between phase and amplitude path in a digital polar power amplifier. The scheme significantly reduces the spectral regrowth. The scheme uses the same path for phase and amplitude delay calculation after the recombination that allows having a robust calibration. Furthermore, it can be executed during the empty transmission slots. The proposed scheme is designed in a 40 nm CMOS technology and simulated with a 64-QAM IEEE 802.11n wireless standard. The scheme achieved 7.57 dB enhancement in ACLR and 84.35% improvement in EVM for a 3.5 ns mismatch in phase and amplitude path

Feed-forward linearisation of a directly modulated semiconductor laser and broadband millimetre-wave wireless over fibre systems.

This thesis is concerned with reduction of non-linear distortion in a directly modulated uncooled semiconductor laser using feed-forward compensation and investigating the performance of broadband millimetre-wave wireless over fibre systems. One of the key elements that determine the performance in a fibre optic link is the linearity of the optical source. Direct modulation of an uncooled semiconductor laser diode is a simple and cost effective solution. However, the distortion and noise generated by the laser limit the achievable dynamic range and performance in a system. Feed-forward linearisation is demonstrated at 5 GHz, the highest operating frequency reported, with 26 dB third order intermodulation distortion suppression and simultaneous noise reduction leading to enhanced spurious free dynamic range of 107 dB (1Hz). The effectiveness of feed-forward in a multi-channel system is investigated. Laser non-linearity can cause spectral re-growth and interchannel distortion that can completely mask the adjacent channel. A significant 11 dB interchannel distortion suppression and 10.5 dB power advantage is obtained compared to the non-linearised case. These results suggest that feed-forward linearisation arrangement can make a practical multi-channel or multi-operator wireless over fibre system. In the second part of this thesis the first experimental transmission of wireless data over fibre with remote millimetre-wave local oscillator delivery using a bi-directional semiconductor optical amplifier in a full duplex system with 2.2 km coarse wavelength division multiplexing fibre ring architecture is demonstrated. The use of bi-directional SOAs in place of unidirectional erbium doped fibre amplifier or unidirectional SOAs, together with the use of CWDM and optical distribution of the local oscillator signal allow substantial reduction in overall complexity and cost. Successful transmission of data over 12.8 km fibre is achieved with clear and well defined constellations and eye diagrams as well as 10.5% and 7.8 % error vector magnitude values for the downlink and uplink directions, respectively. The thesis also presents an implementation and performance of a millimetre-wave gigabit wireless over fibre system. CWDM devices such as uncooled laser diodes and passive components are used for the first time in a gigabit system allowing cost savings compared to dense WDM. This makes such solutions more attractive for millimetre-wave access systems. Optically modulated gigabit wireless data signals to and from the base stations are distributed at 5 GHz and up-converted using a remotely delivered LO source. Eye diagrams and bit error rate are measured to assess the system performance

Radio Communications

In the last decades the restless evolution of information and communication technologies (ICT) brought to a deep transformation of our habits. The growth of the Internet and the advances in hardware and software implementations modified our way to communicate and to share information. In this book, an overview of the major issues faced today by researchers in the field of radio communications is given through 35 high quality chapters written by specialists working in universities and research centers all over the world. Various aspects will be deeply discussed: channel modeling, beamforming, multiple antennas, cooperative networks, opportunistic scheduling, advanced admission control, handover management, systems performance assessment, routing issues in mobility conditions, localization, web security. Advanced techniques for the radio resource management will be discussed both in single and multiple radio technologies; either in infrastructure, mesh or ad hoc networks

Minimum power design of RF front ends

This thesis describes an investigation into the design of RF front ends with minimum power dissipation. The central question is: "What are the fundamental limits for the power dissipation of telecommunication front ends, and what design procedures can be followed that approach these limits and, at the same time, result in practical circuits?" After a discussion of the state of the art in this area, the elementary operations of a front end are identified. For each of these elementary operations, the fundamental limits for the power dissipation are discussed, divided into technology imposed limits and physics imposed limits. A traditional DECT front end design is used to demonstrate the large difference between the fundamental limits and the power dissipation of existing circuits. To improve this situation, first the optimum distribution of specifications across individual subcircuits needs to be determined, such that the requirements for a specific system can be fulfilled. This is achieved through the introduction of formal transforms of the specifications of subcircuits, which correspond with transforms of the subcircuit itself. Using these transforms, the optimum distribution of gain, noise, linearity and power dissipation can be determined. As it turns out, this optimum distribution can even be represented by a simple, analytical expression. This expression predicts that the power dissipation of the DECT front end can be reduced by a factor of 2.7 through an optimum distribution of the specifications. Using these optimum specifications of the subcircuits, the boundaries for further power dissipation reduction can be determined. This is investigated at the system, circuit and technology level. These insights are used in the design of a 2.5GHz wireless local area network, implemented in an optimized technology ("Silicon on Anything"). The power dissipation of the complete receiver is 3.5mW, more than an order of magnitude below other wireless LAN receivers in recent publications. Finally, the combination of this minimum power design method with a platform based development strategy is discussed