Design-for-Test and Test Optimization Techniques for TSV-based 3D Stacked ICs

<p>As integrated circuits (ICs) continue to scale to smaller dimensions, long interconnects</p><p>have become the dominant contributor to circuit delay and a significant component of</p><p>power consumption. In order to reduce the length of these interconnects, 3D integration</p><p>and 3D stacked ICs (3D SICs) are active areas of research in both academia and industry.</p><p>3D SICs not only have the potential to reduce average interconnect length and alleviate</p><p>many of the problems caused by long global interconnects, but they can offer greater design</p><p>flexibility over 2D ICs, significant reductions in power consumption and footprint in</p><p>an era of mobile applications, increased on-chip data bandwidth through delay reduction,</p><p>and improved heterogeneous integration.</p><p>Compared to 2D ICs, the manufacture and test of 3D ICs is significantly more complex.</p><p>Through-silicon vias (TSVs), which constitute the dense vertical interconnects in a</p><p>die stack, are a source of additional and unique defects not seen before in ICs. At the same</p><p>time, testing these TSVs, especially before die stacking, is recognized as a major challenge.</p><p>The testing of a 3D stack is constrained by limited test access, test pin availability,</p><p>power, and thermal constraints. Therefore, efficient and optimized test architectures are</p><p>needed to ensure that pre-bond, partial, and complete stack testing are not prohibitively</p><p>expensive.</p><p>Methods of testing TSVs prior to bonding continue to be a difficult problem due to test</p><p>access and testability issues. Although some built-in self-test (BIST) techniques have been</p><p>proposed, these techniques have numerous drawbacks that render them impractical. In this dissertation, a low-cost test architecture is introduced to enable pre-bond TSV test through</p><p>TSV probing. This has the benefit of not needing large analog test components on the die,</p><p>which is a significant drawback of many BIST architectures. Coupled with an optimization</p><p>method described in this dissertation to create parallel test groups for TSVs, test time for</p><p>pre-bond TSV tests can be significantly reduced. The pre-bond probing methodology is</p><p>expanded upon to allow for pre-bond scan test as well, to enable both pre-bond TSV and</p><p>structural test to bring pre-bond known-good-die (KGD) test under a single test paradigm.</p><p>The addition of boundary registers on functional TSV paths required for pre-bond</p><p>probing results in an increase in delay on inter-die functional paths. This cost of test</p><p>architecture insertion can be a significant drawback, especially considering that one benefit</p><p>of 3D integration is that critical paths can be partitioned between dies to reduce their delay.</p><p>This dissertation derives a retiming flow that is used to recover the additional delay added</p><p>to TSV paths by test cell insertion.</p><p>Reducing the cost of test for 3D-SICs is crucial considering that more tests are necessary</p><p>during 3D-SIC manufacturing. To reduce test cost, the test architecture and test</p><p>scheduling for the stack must be optimized to reduce test time across all necessary test</p><p>insertions. This dissertation examines three paradigms for 3D integration - hard dies, firm</p><p>dies, and soft dies, that give varying degrees of control over 2D test architectures on each</p><p>die while optimizing the 3D test architecture. Integer linear programming models are developed</p><p>to provide an optimal 3D test architecture and test schedule for the dies in the 3D</p><p>stack considering any or all post-bond test insertions. Results show that the ILP models</p><p>outperform other optimization methods across a range of 3D benchmark circuits.</p><p>In summary, this dissertation targets testing and design-for-test (DFT) of 3D SICs.</p><p>The proposed techniques enable pre-bond TSV and structural test while maintaining a</p><p>relatively low test cost. Future work will continue to enable testing of 3D SICs to move</p><p>industry closer to realizing the true potential of 3D integration.</p>Dissertatio

On Mitigation of Side-Channel Attacks in 3D ICs: Decorrelating Thermal Patterns from Power and Activity

Various side-channel attacks (SCAs) on ICs have been successfully demonstrated and also mitigated to some degree. In the context of 3D ICs, however, prior art has mainly focused on efficient implementations of classical SCA countermeasures. That is, SCAs tailored for up-and-coming 3D ICs have been overlooked so far. In this paper, we conduct such a novel study and focus on one of the most accessible and critical side channels: thermal leakage of activity and power patterns. We address the thermal leakage in 3D ICs early on during floorplanning, along with tailored extensions for power and thermal management. Our key idea is to carefully exploit the specifics of material and structural properties in 3D ICs, thereby decorrelating the thermal behaviour from underlying power and activity patterns. Most importantly, we discuss powerful SCAs and demonstrate how our open-source tool helps to mitigate them.Comment: Published in Proc. Design Automation Conference, 201

Investigation into yield and reliability enhancement of TSV-based three-dimensional integration circuits

Three dimensional integrated circuits (3D ICs) have been acknowledged as a promising technology to overcome the interconnect delay bottleneck brought by continuous CMOS scaling. Recent research shows that through-silicon-vias (TSVs), which act as vertical links between layers, pose yield and reliability challenges for 3D design. This thesis presents three original contributions.The first contribution presents a grouping-based technique to improve the yield of 3D ICs under manufacturing TSV defects, where regular and redundant TSVs are partitioned into groups. In each group, signals can select good TSVs using rerouting multiplexers avoiding defective TSVs. Grouping ratio (regular to redundant TSVs in one group) has an impact on yield and hardware overhead. Mathematical probabilistic models are presented for yield analysis under the influence of independent and clustering defect distributions. Simulation results using MATLAB show that for a given number of TSVs and TSV failure rate, careful selection of grouping ratio results in achieving 100% yield at minimal hardware cost (number of multiplexers and redundant TSVs) in comparison to a design that does not exploit TSV grouping ratios. The second contribution presents an efficient online fault tolerance technique based on redundant TSVs, to detect TSV manufacturing defects and address thermal-induced reliability issue. The proposed technique accounts for both fault detection and recovery in the presence of three TSV defects: voids, delamination between TSV and landing pad, and TSV short-to-substrate. Simulations using HSPICE and ModelSim are carried out to validate fault detection and recovery. Results show that regular and redundant TSVs can be divided into groups to minimise area overhead without affecting the fault tolerance capability of the technique. Synthesis results using 130-nm design library show that 100% repair capability can be achieved with low area overhead (4% for the best case). The last contribution proposes a technique with joint consideration of temperature mitigation and fault tolerance without introducing additional redundant TSVs. This is achieved by reusing spare TSVs that are frequently deployed for improving yield and reliability in 3D ICs. The proposed technique consists of two steps: TSV determination step, which is for achieving optimal partition between regular and spare TSVs into groups; The second step is TSV placement, where temperature mitigation is targeted while optimizing total wirelength and routing difference. Simulation results show that using the proposed technique, 100% repair capability is achieved across all (five) benchmarks with an average temperature reduction of 75.2? (34.1%) (best case is 99.8? (58.5%)), while increasing wirelength by a small amount

Test Planning for 3D SICs using ILP

In this paper we propose a test planning scheme for corebased 3D stacked integrated circuits where the total test cost for wafer sort of each individual chip and the test cost of the complete stack at package test is minimized. We use an Integer Linear Programming (ILP) model to find the optimal test cost, which is given as the weighted sum of the test time and the test access mechanism (TAM). As ILP is time consuming, we use a scheme to bound the test time and the TAM such that the search space is reduced. The proposed bounding scheme and the ILP model were applied on several ITC’02 benchmarks and the results show that optimal solutions were obtained at low computation time

TSV placement optimization for liquid cooled 3D-ICs with emerging NVMs

Three dimensional integrated circuits (3D-ICs) are a promising solution to the performance bottleneck in planar integrated circuits. One of the salient features of 3D-ICs is their ability to integrate heterogeneous technologies such as emerging non-volatile memories (NVMs) in a single chip. However, thermal management in 3D-ICs is a significant challenge, owing to the high heat flux (~ 250 W/cm2). Several research groups have focused either on run-time or design-time mechanisms to reduce the heat flux and did not consider 3D-ICs with heterogeneous stacks. The goal of this work is to achieve a balanced thermal gradient in 3D-ICs, while reducing the peak temperatures. In this research, placement algorithms for design-time optimization and choice of appropriate cooling mechanisms for run-time modulation of temperature are proposed. Specifically, an architectural framework which introduce weight-based simulated annealing (WSA) algorithm for thermal-aware placement of through silicon vias (TSVs) with inter-tier liquid cooling is proposed for design-time. In addition, integrating a dedicated stack of emerging NVMs such as RRAM, PCRAM and STTRAM, a run-time simulation framework is developed to analyze the thermal and performance impact of these NVMs in 3D-MPSoCs with inter-tier liquid cooling. Experimental results of WSA algorithm implemented on MCNC91 and GSRC benchmarks demonstrate up to 11 K reduction in the average temperature across the 3D-IC chip. In addition, power density arrangement in WSA improved the uniformity by 5%. Furthermore, simulation results of PARSEC benchmarks with NVM L2 cache demonstrates a temperature reduction of 12.5 K (RRAM) compared to SRAM in 3D-ICs. Especially, RRAM has proved to be thermally efficient replacement for SRAM with 34% lower energy delay product (EDP) and 9.7 K average temperature reduction

Electromigration modeling and layout optimization for advanced VLSI

textElectromigration (EM) is a critical problem for interconnect reliability in advanced VLSI design. Because EM is a strong function of current density, a smaller cross-sectional area of interconnects can degrade the EM-related lifetime of IC, which is expected to become more severe in future technology nodes. Moreover, as EM is governed by various factors such as temperature, material property, geometrical shape, and mechanical stress, different interconnect structures can have distinct EM issues and solutions to mitigate them. For example, one of the most prominent technologies, die stacking technology of three-dimensional (3D) ICs, can have different EM problems from that of planer ICs, due to their unique interconnects such as through-silicon vias (TSVs). This dissertation investigates EM in various interconnect structures, and applies the EM models to optimize IC layout. First, modeling of EM is developed for chip-level interconnects, such as wires, local vias, TSVs, and multi-scale vias (MSVs). Based on the models, fast and accurate EM-prediction methods are proposed for the chip-level designs. After that, by utilizing the EM-prediction methods, the layout optimization methods are suggested, such as EM-aware routing for 3D ICs and EM-aware redundant via insertion for the future technology nodes in VLSI. Experimental results show that the proposed EM modeling approaches enable fast and accurate EM evaluation for chip design, and the EM-aware layout optimization methods improve EM-robustness of advanced VLSI designs.Electrical and Computer Engineerin

CAD methodologies for low power and reliable 3D ICs

The main objective of this dissertation is to explore and develop computer-aided-design (CAD) methodologies and optimization techniques for reliability, timing performance, and power consumption of through-silicon-via(TSV)-based and monolithic 3D IC designs. The 3D IC technology is a promising answer to the device scaling and interconnect problems that industry faces today. Yet, since multiple dies are stacked vertically in 3D ICs, new problems arise such as thermal, power delivery, and so on. New physical design methodologies and optimization techniques should be developed to address the problems and exploit the design freedom in 3D ICs. Towards the objective, this dissertation includes four research projects. The first project is on the co-optimization of traditional design metrics and reliability metrics for 3D ICs. It is well known that heat removal and power delivery are two major reliability concerns in 3D ICs. To alleviate thermal problem, two possible solutions have been proposed: thermal-through-silicon-vias (T-TSVs) and micro-fluidic-channel (MFC) based cooling. For power delivery, a complex power distribution network is required to deliver currents reliably to all parts of the 3D IC while suppressing the power supply noise to an acceptable level. However, these thermal and power networks pose major challenges in signal routability and congestion. In this project, a co-optimization methodology for signal, power, and thermal interconnects in 3D ICs is presented. The goal of the proposed approach is to improve signal, thermal, and power noise metrics and to provide fast and accurate design space explorations for early design stages. The second project is a study on 3D IC partition. For a 3D IC, the target circuit needs to be partitioned into multiple parts then mapped onto the dies. The partition style impacts design quality such as footprint, wirelength, timing, and so on. In this project, the design methodologies of 3D ICs with different partition styles are demonstrated. For the LEON3 multi-core microprocessor, three partitioning styles are compared: core-level, block-level, and gate-level. The design methodologies for such partitioning styles and their implications on the physical layout are discussed. Then, to perform timing optimizations for 3D ICs, two timing constraint generation methods are demonstrated that lead to different design quality. The third project is on the buffer insertion for timing optimization of 3D ICs. For high performance 3D ICs, it is crucial to perform thorough timing optimizations. Among timing optimization techniques, buffer insertion is known to be the most effective way. The TSVs have a large parasitic capacitance that increases the signal slew and the delay on the downstream. In this project, a slew-aware buffer insertion algorithm is developed that handles full 3D nets and considers TSV parasitics and slew effects on delay. Compared with the well-known van Ginneken algorithm and a commercial tool, the proposed algorithm finds buffering solutions with lower delay values and acceptable runtime overhead. The last project is on the ultra-high-density logic designs for monolithic 3D ICs. The nano-scale 3D interconnects available in monolithic 3D IC technology enable ultra-high-density device integration at the individual transistor-level. The benefits and challenges of monolithic 3D integration technology for logic designs are investigated. First, a 3D standard cell library for transistor-level monolithic 3D ICs is built and their timing and power behavior are characterized. Then, various interconnect options for monolithic 3D ICs that improve design quality are explored. Next, timing-closed, full-chip GDSII layouts are built and iso-performance power comparisons with 2D IC designs are performed. Important design metrics such as area, wirelength, timing, and power consumption are compared among transistor-level monolithic 3D, gate-level monolithic 3D, TSV-based 3D, and traditional 2D designs.PhDCommittee Chair: Lim, Sung Kyu; Committee Member: Bakir, Muhannad; Committee Member: Kim, Hyesoon; Committee Member: Lee, Hsien-Hsin; Committee Member: Mukhopadhyay, Saiba

Heterogeneous 2.5D integration on through silicon interposer

© 2015 AIP Publishing LLC. Driven by the need to reduce the power consumption of mobile devices, and servers/data centers, and yet continue to deliver improved performance and experience by the end consumer of digital data, the semiconductor industry is looking for new technologies for manufacturing integrated circuits (ICs). In this quest, power consumed in transferring data over copper interconnects is a sizeable portion that needs to be addressed now and continuing over the next few decades. 2.5D Through-Si-Interposer (TSI) is a strong candidate to deliver improved performance while consuming lower power than in previous generations of servers/data centers and mobile devices. These low-power/high-performance advantages are realized through achievement of high interconnect densities on the TSI (higher than ever seen on Printed Circuit Boards (PCBs) or organic substrates), and enabling heterogeneous integration on the TSI platform where individual ICs are assembled at close proximity

Radiation safety based on the sky shine effect in reactor

In the reactor operation, neutrons and gamma rays are the most dominant radiation. As protection, lead and concrete shields are built around the reactor. However, the radiation can penetrate the water shielding inside the reactor pool. This incident leads to the occurrence of sky shine where a physical phenomenon of nuclear radiation sources was transmitted panoramic that extends to the environment. The effect of this phenomenon is caused by the fallout radiation into the surrounding area which causes the radiation dose to increase. High doses of exposure cause a person to have stochastic effects or deterministic effects. Therefore, this study was conducted to measure the radiation dose from sky shine effect that scattered around the reactor at different distances and different height above the reactor platform. In this paper, the analysis of the radiation dose of sky shine effect was measured using the experimental metho

Design for pre-bond testability in 3D integrated circuits

In this dissertation we propose several DFT techniques specific to 3D stacked IC systems. The goal has explicitly been to create techniques that integrate easily with existing IC test systems. Specifically, this means utilizing scan- and wrapper-based techniques, two foundations of the digital IC test industry. First, we describe a general test architecture for 3D ICs. In this architecture, each tier of a 3D design is wrapped in test control logic that both manages tier test pre-bond and integrates the tier into the large test architecture post-bond. We describe a new kind of boundary scan to provide the necessary test control and observation of the partial circuits, and we propose a new design methodology for test hardcore that ensures both pre-bond functionality and post-bond optimality. We present the application of these techniques to the 3D-MAPS test vehicle, which has proven their effectiveness. Second, we extend these DFT techniques to circuit-partitioned designs. We find that boundary scan design is generally sufficient, but that some 3D designs require special DFT treatment. Most importantly, we demonstrate that the functional partitioning inherent in 3D design can potentially decrease the total test cost of verifying a circuit. Third, we present a new CAD algorithm for designing 3D test wrappers. This algorithm co-designs the pre-bond and post-bond wrappers to simultaneously minimize test time and routing cost. On average, our algorithm utilizes over 90% of the wires in both the pre-bond and post-bond wrappers. Finally, we look at the 3D vias themselves to develop a low-cost, high-volume pre-bond test methodology appropriate for production-level test. We describe the shorting probes methodology, wherein large test probes are used to contact multiple small 3D vias. This technique is an all-digital test method that integrates seamlessly into existing test flows. Our experimental results demonstrate two key facts: neither the large capacitance of the probe tips nor the process variation in the 3D vias and the probe tips significantly hinders the testability of the circuits. Taken together, this body of work defines a complete test methodology for testing 3D ICs pre-bond, eliminating one of the key hurdles to the commercialization of 3D technology.PhDCommittee Chair: Lee, Hsien-Hsin; Committee Member: Bakir, Muhannad; Committee Member: Lim, Sung Kyu; Committee Member: Vuduc, Richard; Committee Member: Yalamanchili, Sudhaka