Memory Module Design for High-Temperature Applications in SiC CMOS Technology

The wide bandgap (WBG) characteristics of SiC play a significant and disruptive role in the power electronics industry. The same characteristics make this material a viable choice for high-temperature electronics systems. Leveraging the high-temperature capability of SiC is crucial to automotive, space exploration, aerospace, deep well drilling, and gas turbines. A significant issue with the high-temperature operation is the exponential increase in leakage current. The lower intrinsic carrier concentration of SiC (10-9 cm-3) compared to Si (1010 cm-3) leads to lower leakage over temperature. Several researchers have demonstrated analog and digital circuits designed in SiC. However, a memory module is required to realize a complete electronic system in SiC that bridges the gap between data processing and data storage. Designing memory that can process massive amounts of data in harsh environments while consuming low power opens doors for future electronics. A novel static random-access memory (SRAM) cell is designed and implemented in a SiC 1 µm triple well CMOS process for high-temperature applications in this work. The prevalent issues encountered during SiC fabrication and the uncertainties in device performance led to 6T SRAM cell design modifications that enable adaptability to the worst and the best cases. However, design trade-offs are made in the design size, the number of transistors, number of I/Os, and the cell\u27s power consumption. The novel SRAM cell design mitigates the effect of poor p-type contacts after the device fabrication by controlling the cell\u27s drive strength via an additional pull-up network. The design also includes two parallel access transistors and separate wordlines that control both access transistors. This individual control enables post-fabrication tunability in the cell ratio (CR) and the pull-up (PR) ratio of the cell. It also allows tuning the access transistors\u27 effective width during a data read operation, and a data write operation, independently. Along with the SRAM cell design, the conventional latch-based sense amplifier is also designed in the SiC CMOS process to realize the monolithic memory IC modules. The SRAM cell performance is evaluated on the basis of static noise margin (SNM), write SNM (WSNM), read SNM (RSNM), leakage current, and read access time over a wide temperature range (25ºC to 500ºC) on three uniquely processed wafers. The noise margins measured on Wafer #2 show a lower leakage current of ~500 nA at 500ºC with the supply voltage of 10 V. The SNM of 6.07 V is measured at 500ºC with a 10 V of power supply. The read access time at 400ºC is ~7.5 µs at a supply voltage of 10 V

Design of Digital SoC for Operation at High Temperatures

There is a growing demand for Systems-on-Chip, integrating microprocessors, on-chip memories, data converters and a variety of sensors, which are capable of reliable operation at high temperatures. For instance, modern aircraft industry demands microcontrollers and electric motors to operate at high temperatures, in order to replace present hydraulic structures. This thesis explains how to design digital SoC which are capable of reliable operation at high temperatures. The essential part of this thesis focuses on the design, implementation, fabrication and high-temperature measurements of on-chip Latch based SRAM, PowerPC e200 based microcontroller, digital temperature sensor and Flash A/D converter. Embedded on-chip SRAM modules are one of the most important components in the modern SoC. We analyze thermally-caused failures in the 6T SRAM cell and elaborate on its reliability. Further, we show that Latch based SRAM modules are preferable to 6T SRAM for reliable operation beyond 150C, by comparing two 1kB SRAM modules implemented in standard 0.18um SOI CMOS process. We demonstrate reliable SRAM operation at 275C (fmax = 10MHz, Ptot = 400mW), that is by far the highest reported operating temperature for digital on-chip SRAM module. Designing SoCs for reliable operation at elevated temperatures is a significant challenge, due to increased static leakage current, reduced carrier mobility, and increased electromigration. We propose to customize a PowerPC e200 based SoC by using a dynamically reconfigurable clock frequency, exhaustive clock gating, and electromigration-resistant power distribution network. We fabricated a 20x9mm2 chip implementing this design in 0.35um Bulk CMOS process. We present worldâs first PowerPC based SoC for reliable operation at 225C (fmax = 30MHz, Ptot = 1.2W). This design outperforms previously reported PowerPC based SoCs, which are not operational at temperatures beyond 125C. The on-chip measurements of the p-n junction temperature allow reliability improvements for the SoC that operates at high temperatures. Low-resolution temperature measurements are efficiently used for adjusting the optimal operation frequency and supply voltage. We used the Time-to-Digital conversion technique to design a fully-digital temperature sensor. We designed and simulated a fully-digital 5bit temperature sensor for 10C resolution temperature measurements in between Tj,min = -45C and Tj,max = 125C. Further, using a single clock cycle Time-to-Digital conversion technique, we present a fully-digital 5bit Pulse based Flash ADC implemented in 0.18um Bulk CMOS process. Measurement results demonstrate the state-of-the-art power efficiency result of 450 fJ/conv (fmax = 83MHz, Ptot = 900uW)

Robust Circuit Design for Low-Voltage VLSI.

Voltage scaling is an effective way to reduce the overall power consumption, but the major challenges in low voltage operations include performance degradation and reliability issues due to PVT variations. This dissertation discusses three key circuit components that are critical in low-voltage VLSI. Level converters must be a reliable interface between two voltage domains, but the reduced on/off-current ratio makes it extremely difficult to achieve robust conversions at low voltages. Two static designs are proposed: LC2 adopts a novel pulsed-operation and modulates its pull-up strength depending on its state. A 3-sigma robustness is guaranteed using a current margin plot; SLC inherently reduces the contention by diode-insertion. Improvements in performance, power, and robustness are measured from 130nm CMOS test chips. SRAM is a major bottleneck in voltage-scaling due to its inherent ratioed-bitcell design. The proposed 7T SRAM alleviates the area overhead incurred by 8T bitcells and provides robust operation down to 0.32V in 180nm CMOS test chips with 3.35fW/bit leakage. Auto-Shut-Off provides a 6.8x READ energy reduction, and its innate Quasi-Static READ has been demonstrated which shows a much improved READ error rate. A use of PMOS Pass-Gate improves the half-select robustness by directly modulating the device strength through bitline voltage. Clocked sequential elements, flip-flops in short, are ubiquitous in today’s digital systems. The proposed S2CFF is static, single-phase, contention-free, and has the same number of devices as in TGFF. It shows a 40% power reduction as well as robust low-voltage operations in fabricated 45nm SOI test chips. Its simple hold-time path and the 3.4x improvement in 3-sigma hold-time is presented. A new on-chip flip-flop testing harness is also proposed, and measured hold-time variations of flip-flops are presented.PhDElectrical EngineeringUniversity of Michigan, Horace H. Rackham School of Graduate Studieshttp://deepblue.lib.umich.edu/bitstream/2027.42/111525/1/yejoong_1.pd

A Process Variation Tolerant Self-Compensation Sense Amplifier Design

As we move under the aegis of the Moore\u27s law, we have to deal with its darker side with problems like leakage and short channel effects. Once we go beyond 45nm regime process variations also have emerged as a significant design concern.Embedded memories uses sense amplifier for fast sensing and typically, sense amplifiers uses pair of matched transistors in a positive feedback environment. A small difference in voltage level of applied input signals to these matched transistors is amplified and the resulting logic signals are latched. Intra die variation causes mismatch between the sense transistors that should ideally be identical structures. Yield loss due to device and process variations has never been so critical to cause failure in circuits. Due to growth in size of embedded SRAMs as well as usage of sense amplifier based signaling techniques, process variations in sense amplifiers leads to significant loss of yield for that we need to come up with process variation tolerant circuit styles and new devices. In this work impact of transistor mismatch due to process variations on sense amplifier is evaluated and this problem is stated. For the solution of the problem a novel self compensation scheme on sense amplifiers is presented on different technology nodes up to 32nm on conventional bulk MOSFET technology. Our results show that the self compensation technique in the conventional bulk MOSFET latch type sense amplifier not just gives improvement in the yield but also leads to improvement in performance for latch type sense amplifiers. Lithography related CD variations, fluctuations in dopant density, oxide thickness and parametric variations of devices are identified as a major challenge to the classical bulk type MOSFET. With the emerging nanoscale devices, SIA roadmap identifies FinFETs as a candidate for post-planar end-of-roadmap CMOS device. With current technology scaling issues and with conventional bulk type MOSFET on 32nm node our technique can easily be applied to Double Gate devices. In this work, we also develop the model of Double Gate MOSFET through 3D Device Simulator Damocles and TCAD simulator. We propose a FinFET based process variation tolerant sense amplifier design that exploits the back gate of FinFET devices for dynamic compensation against process variations. Results from statistical simulation show that the proposed dynamic compensation is highly effective in restoring yield at a level comparable to that of sense amplifiers without process variations. We created the 32nm double gate models generated from Damocles 3-D device simulations [25] and Taurus Device Simulator available commercially from Synopsys [47] and use them in the nominal latch type sense amplifier design and on the Independent Gate Self Compensation Sense Amplifier Design (IGSSA) to compare the yield and performance benefits of sense amplifier design on FinFET technology over the conventional bulk type CMOS based sense amplifier on 32nm technology node effective in restoring yield at a level comparable to that of sense amplifiers without process variations. We created the 32nm double gate models generated from Damocles 3-D device simulations [25] and Taurus Device Simulator available commercially from Synopsys [47] and use them in the nominal latch type sense amplifier design and on the Independent Gate Self Compensation Sense Amplifier Design (IGSSA) to compare the yield and performance benefits of sense amplifier design on FinFET technology over the conventional bulk type CMOS based sense amplifier on 32nm technology node

Design of Low-Voltage Digital Building Blocks and ADCs for Energy-Efficient Systems

Increasing number of energy-limited applications continue to drive the demand for designing systems with high energy efficiency. This tutorial covers the main building blocks of a system implementation including digital logic, embedded memories, and analog-to-digital converters and describes the challenges and solutions to designing these blocks for low-voltage operation

High-Performance Energy-Efficient and Reliable Design of Spin-Transfer Torque Magnetic Memory

In this dissertation new computing paradigms, architectures and design philosophy are proposed and evaluated for adopting the STT-MRAM technology as highly reliable, energy efficient and fast memory. For this purpose, a novel cross-layer framework from the cell-level all the way up to the system- and application-level has been developed. In these framework, the reliability issues are modeled accurately with appropriate fault models at different abstraction levels in order to analyze the overall failure rates of the entire memory and its Mean Time To Failure (MTTF) along with considering the temperature and process variation effects. Design-time, compile-time and run-time solutions have been provided to address the challenges associated with STT-MRAM. The effectiveness of the proposed solutions is demonstrated in extensive experiments that show significant improvements in comparison to state-of-the-art solutions, i.e. lower-power, higher-performance and more reliable STT-MRAM design

Static random-access memory designs based on different FinFET at lower technology node (7nm)

Title from PDF of title page viewed January 15, 2020Thesis advisor: Masud H ChowdhuryVitaIncludes bibliographical references (page 50-57)Thesis (M.S.)--School of Computing and Engineering. University of Missouri--Kansas City, 2019The Static Random-Access Memory (SRAM) has a significant performance impact on current nanoelectronics systems. To improve SRAM efficiency, it is important to utilize emerging technologies to overcome short-channel effects (SCE) of conventional CMOS. FinFET devices are promising emerging devices that can be utilized to improve the performance of SRAM designs at lower technology nodes. In this thesis, I present detail analysis of SRAM cells using different types of FinFET devices at 7nm technology. From the analysis, it can be concluded that the performance of both 6T and 8T SRAM designs are improved. 6T SRAM achieves a 44.97% improvement in the read energy compared to 8T SRAM. However, 6T SRAM write energy degraded by 3.16% compared to 8T SRAM. Read stability and write ability of SRAM cells are determined using Static Noise Margin and N- curve methods. Moreover, Monte Carlo simulations are performed on the SRAM cells to evaluate process variations. Simulations were done in HSPICE using 7nm Asymmetrical Underlap FinFET technology. The quasiplanar FinFET structure gained considerable attention because of the ease of the fabrication process [1] – [4]. Scaling of technology have degraded the performance of CMOS designs because of the short channel effects (SCEs) [5], [6]. Therefore, there has been upsurge in demand for FinFET devices for emerging market segments including artificial intelligence and cloud computing (AI) [8], [9], Internet of Things (IoT) [10] – [13] and biomedical [17] –[18] which have their own exclusive style of design. In recent years, many Underlapped FinFET devices were proposed to have better control of the SCEs in the sub-nanometer technologies [3], [4], [19] – [33]. Underlap on either side of the gate increases effective channel length as seen by the charge carriers. Consequently, the source-to-drain tunneling probability is improved. Moreover, edge direct tunneling leakage components can be reduced by controlling the electric field at the gate-drain junction . There is a limitation on the extent of underlap on drain or source sides because the ION is lower for larger underlap. Additionally, FinFET based designs have major width quantization issue. The width of a FinFET device increases only in quanta of silicon fin height (HFIN) [4]. The width quantization issue becomes critical for ratioed designs like SRAMs, where proper sizing of the transistors is essential for fault-free operation. FinFETs based on Design/Technology Co-Optimization (DTCO_F) approach can overcome these issues [38]. DTCO_F follows special design rules, which provides the specifications for the standard SRAM cells with special spacing rules and low leakages. The performances of 6T SRAM designs implemented by different FinFET devices are compared for different pull-up, pull down and pass gate transistor (PU: PD:PG) ratios to identify the best FinFET device for high speed and low power SRAM applications. Underlapped FinFETs (UF) and Design/Technology Co-Optimized FinFETs (DTCO_F) are used for the design and analysis. It is observed that with the PU: PD:PG ratios of 1:1:1 and 1:5:2 for the UF-SRAMs the read energy has degraded by 3.31% and 48.72% compared to the DTCO_F-SRAMs, respectively. However, the read energy with 2:5:2 ratio has improved by 32.71% in the UF-SRAM compared to the DTCO_F-SRAMs. The write energy with 1:1:1 configuration has improved by 642.27% in the UF-SRAM compared to the DTCO_F-SRAM. On the other hand, the write energy with 1:5:2 and 2:5:2 configurations have degraded by 86.26% and 96% in the UF-SRAMs compared to the DTCO_F-SRAMs. The stability and reliability of different SRAMs are also evaluated for 500mV supply. From the analysis, it can be concluded that Asymmetrical Underlapped FinFET is better for high-speed applications and DTCO FinFET for low power applications.Introduction -- Next generation high performance device: FinFET -- FinFET based SRAM bitcell designs -- Benchmarking of UF-SRAMs and DTCO-F-SRAMS -- Collaborative project -- Internship experience at INTEL and Marvell Semiconductor -- Conclusion and future wor