Design Exploration of mm-Wave Integrated Transceivers for Short-Range Mobile Communications Towards 5G

This paper presents a design exploration, at both system and circuit levels, of integrated transceivers for the upcoming fifth generation (5G) of wireless communications. First, a system level model for 5G communications is carried out to derive transceiver design specifications. Being 5G still in pre-standardization phase, a few currently used standards (ECMA-387, IEEE 802.15.3c, and LTE-A) are taken into account as the reference for the signal format. Following a top-down flow, this work presents the design in 65nm CMOS SOI and bulk technologies of the key blocks of a fully integrated transceiver: low noise amplifier (LNA), power amplifier (PA) and on-chip antenna. Different circuit topologies are presented and compared allowing for different trade-offs between gain, power consumption, noise figure, output power, linearity, integration cost and link performance. The best configuration of antenna and LNA co-design results in a peak gain higher than 27dB, a noise figure below 5dB and a power consumption of 35mW. A linear PA design is presented to face the high Peak to Average Power Ratio (PAPR) of multi-carrier transmissions envisaged for 5G, featuring a 1dB compression point output power (OP1dB) of 8.2dBm. The delivered output power in the linear region can be increased up to 13.2dBm by combining four basic PA blocks through a Wilkinson power combiner/divider circuit. The proposed circuits are shown to enable future 5G connections, operating in a mm-wave spectrum range (spanning 9GHz, from 57GHz to 66GHz), with a data-rate of several Gb/s in a short-range scenario, spanning from few centimeters to tens of meters

Millimeter-Wave Wideband Low-Noise Amplifiers in 22FFL Technology

The deployment of advanced technology standards for 5G and beyond in cellular networks has resulted in interest in integrated circuits (ICs) operating at frequencies above 10GHz. This has sparked research on wideband circuits in commercial low-cost silicon technologies, operating at high RF and mm-wave frequencies. Given the wide range of operating frequencies (28GHz, 30GHz and 47GHz), such circuits must satisfy performance parameters across wide operating range. This thesis focuses on the implementation of wideband low-noise amplifiers (LNA) and addresses design challenges associated with mm-wave wideband impedance matching networks in state-of-the-art CMOS technologies

Architectures, Antennas and Circuits for Millimeter-wave Wireless Full-Duplex Applications

Demand for wireless network capacity keeps growing exponentially every year, as a result a 1000-fold increase in data traffic is projected over the next 10 years in the context of 5G wireless networks. Solutions for delivering the 1000-fold increase in capacity fall into three main categories: deploying smaller cells, allocating more spectrum and improving spectral efficiency of wireless systems. Smaller cells at RF frequencies (1-6GHz) are unlikely to deliver the demanded capacity increase. On the other hand, millimeter-wave spectrum (frequencies over 24GHz) offers wider, multi-GHz channel bandwidths, and therefore has gained significant research interest as one of the most promising solutions to address the data traffic demands of 5G. Another disruptive technology is full-duplex which breaks a century-old assumption in wireless communication, by simultaneous transmission and reception on the same frequency channel. In doing so, full-duplex offers many benefits for wireless networks, including an immediate spectral efficiency improvement in the physical layer. Although FD promises great benefits, self-interference from the transmitter to its own receiver poses a fundamental challenge. The self-interference can be more than a billion times stronger than the desired signal and must be suppressed below the receiver noise floor. In recent years, there has been some research efforts on fully-integrated full-duplex RF transceivers, but mm-wave fully-integrated full-duplex systems, are still in their infancy. This dissertation presents novel architectures, antenna and circuit techniques to merge two exciting technologies, mm-wave and full-duplex, which can potentially offer the dual benefits of wide bandwidths and improved spectral efficiency. To this end, two different antenna interfaces, namely a wideband reconfigurable T/R antenna pair with polarization-based antenna cancellation and an mm-wave fully-integrated magnetic-free non-reciprocal circulator, are presented. The polarization-based antenna cancellation is employed in conjunction with the RF and digital cancellation to design a 60GHz full-duplex 45nm SOI CMOS transceiver with nearly 80dB self-interference suppression. The concepts and prototypes presented in this dissertation have also profound implications for emerging applications such as vehicular radars, 5G small-cell base-stations and virtual reality

Quadrature Phase-Domain ADPLL with Integrated On-line Amplitude Locked Loop Calibration for 5G Multi-band Applications

5th generation wireless systems (5G) have expanded frequency band coverage with the low-band 5G and mid-band 5G frequencies spanning 600 MHz to 4 GHz spectrum. This dissertation focuses on a microelectronic implementation of CMOS 65 nm design of an All-Digital Phase Lock Loop (ADPLL), which is a critical component for advanced 5G wireless transceivers. The ADPLL is designed to operate in the frequency bands of 600MHz-930MHz, 2.4GHz-2.8GHz and 3.4GHz-4.2GHz. Unique ADPLL sub-components include: 1) Digital Phase Frequency Detector, 2) Digital Loop Filter, 3) Channel Bank Select Circuit, and 4) Digital Control Oscillator. Integrated with the ADPLL is a 90-degree active RC-CR phase shifter with on-line amplitude locked loop (ALL) calibration to facilitate enhanced image rejection while mitigating the effects of fabrication process variations and component mismatch. A unique high-sensitivity high-speed dynamic voltage comparator is included as a key component of the active phase shifter/ALL calibration subsystem. 65nm CMOS technology circuit designs are included for the ADPLL and active phase shifter with simulation performance assessments. Phase noise results for 1 MHz offset with carrier frequencies of 600MHz, 2.4GHz, and 3.8GHz are -130, -122, and -116 dBc/Hz, respectively. Monte Carlo simulations to account for process variations/component mismatch show that the active phase shifter with ALL calibration maintains accurate quadrature phase outputs when operating within the frequency bands 600MHz-930MHz, 2.4GHz-2.8GHz and 3.4GHz-4.2GHz

High Performance Local Oscillator Design for Next Generation Wireless Communication

Local Oscillator (LO) is an essential building block in modern wireless radios. In modern wireless radios, LO often serves as a reference of the carrier signal to modulate or demod- ulate the outgoing or incoming data. The LO signal should be a clean and stable source, such that the frequency or timing information of the carrier reference can be well-defined. However, as radio architecture evolves, the importance of LO path design has become much more important than before. Of late, many radio architecture innovations have exploited sophisticated LO generation schemes to meet the ever-increasing demands of wireless radio performances. The focus of this thesis is to address challenges in the LO path design for next-generation high performance wireless radios. These challenges include (1) Congested spectrum at low radio frequency (RF) below 5GHz (2) Continuing miniaturization of integrated wireless radio, and (3) Fiber-fast (>10Gb/s) mm-wave wireless communication. The thesis begins with a brief introduction of the aforementioned challenges followed by a discussion of the opportunities projected to overcome these challenges. To address the challenge of congested spectrum at frequency below 5GHz, novel ra- dio architectures such as cognitive radio, software-defined radio, and full-duplex radio have drawn significant research interest. Cognitive radio is a radio architecture that opportunisti- cally utilize the unused spectrum in an environment to maximize spectrum usage efficiency. Energy-efficient spectrum sensing is the key to implementing cognitive radio. To enable energy-efficient spectrum sensing, a fast-hopping frequency synthesizer is an essential build- ing block to swiftly sweep the carrier frequency of the radio across the available spectrum. Chapter 2 of this thesis further highlights the challenges and trade-offs of the current LO gen- eration scheme for possible use in sweeping LO-based spectrum analysis. It follows by intro- duction of the proposed fast-hopping LO architecture, its implementation and measurement results of the validated prototype. Chapter 3 proposes an embedded phase-shifting LO-path design for wideband RF self-interference cancellation for full-duplex radio. It demonstrates a synergistic design between the LO path and signal to perform self-interference cancellation. To address the challenge of continuing miniaturization of integrated wireless radio, ring oscillator-based frequency synthesizer is an attractive candidate due to its compactness. Chapter 4 discussed the difficulty associated with implementing a Phase-Locked Loop (PLL) with ultra-small form-factor. It further proposes the concept sub-sampling PLL with time- based loop filter to address these challenges. A 65nm CMOS prototype and its measurement result are presented for validation of the concept. In shifting from RF to mm-wave frequencies, the performance of wireless communication links is boosted by significant bandwidth and data-rate expansion. However, the demand for data-rate improvement is out-pacing the innovation of radio architectures. A >10Gb/s mm-wave wireless communication at 60GHz is required by emerging applications such as virtual-reality (VR) headsets, inter-rack data transmission at data center, and Ultra-High- Definition (UHD) TV home entertainment systems. Channel-bonding is considered to be a promising technique for achieving >10Gb/s wireless communication at 60GHz. Chapter 5 discusses the fundamental radio implementation challenges associated with channel-bonding for 60GHz wireless communication and the pros and cons of prior arts that attempted to address these challenges. It is followed by a discussion of the proposed 60GHz channel- bonding receiver, which utilizes only a single PLL and enables both contiguous and non- contiguous channel-bonding schemes. Finally, Chapter 6 presents the conclusion of this thesis

High-Performance Multi-Antenna Wireless for 5G and Beyond

Over the next decade, multi-antenna radios, including phased array and multiple-input-multiple-output (MIMO) radios, are expected to play an essential role in the next-generation of wireless networks. Phased arrays can reject spatial interferences and provide coherent beamforming gain, and MIMO technology promises to significantly enhance the system performance in the coverage, capacity, and user data rate through the beamforming or diversity/capacity gain which can substantially increase the range in wireless links, that are challenged from the transmitter (TX) power handling, receiver (RX) noise perspectives and a multi-path environment. Furthermore, the multi-user MIMO (MU-MIMO) can simultaneously serve multiple users which is vital for femtocell base stations and access points (AP). Full-duplex (FD) wireless, namely simultaneous transmission and reception at the same frequency, is an emerging technology that has gained attention due to its potential to double the data throughput, as well as provide other benefits in the higher layers such as better spectral efficiency, reducing network and feedback signaling delays, and resolving hidden-node problems to avoid collisions. However, several challenges remain in the quest for the high-performance integrated FD radios. Transmitter power handling remains an open problem, particularly in FD radios that integrate a shared antenna interface. Secondly, FD operation must be achieved across antenna VSWR variations and a changing EM environment. Finally, FD must be extended to multi-antenna radios, including phased array and multi-input multi-output (MIMO) radios, as over the next decade, they are expected to play an essential role in the next generation of wireless networks. Multi-antenna FD operation, however, is challenged not only by the self-interference (SI) from each TX to its own RX but also cross-talk SI (CT-SI) between antennas. In this dissertation, first, a full-duplex phased array circulator-RX (circ.-RX) is proposed that achieves self-interference cancellation (SIC) through repurposing beamforming degrees of freedom (DoF) on TX and RX. Then, an FD MIMO circ.-RX is proposed that achieves SI and CT-SI cancellation (CT-SIC) through passive RF and shared-delay baseband (BB) canceller that addresses challenges associated with FD MIMO operation. Wireless radios at millimeter-wave (mm-wave) frequencies enable the high-speed link for portable devices due to the wide-band spectrum available. Large-scale arrays are required to compensate for high path loss to form an mm-wave link. Mm-wave MIMO systems with digitization enable virtual arrays for radar, digital beamforming (DBF) for high mobility scenarios and spatial multiplexing. To preserve MIMO information, the received signal from each element in MIMO RX should be transported to ADC/DSP IC for DBF, and vice versa on the TX side. A large-scale array can be formed by tiling multiple mm-wave IC front-ends, and thus, a single-wire interface is desired between DSP IC and mm-wave ICs to reduce board routing complexity. Per-element digitization poses the challenge of handling high data-rate I/O in large-scale tiled MIMO mm-wave arrays. SERializer – DESerializer (SERDES) is traditionally being used as a high-speed link in computing systems and networks. However, SERDES results in a large area and power consumption. In this dissertation, a 60~GHz 4-element MIMO TX with a single-wire interface is presented that de-multiplexes the baseband signal of all elements and LO reference that are frequency-domain multiplexed on a single-wire coax cable