Low-Power, Low-Cost, & High-Performance Digital Designs : Multi-bit Signed Multiplier design using 32nm CMOS Technology

Binary multipliers are ubiquitous in digital hardware. Digital multipliers along with the adders play a major role in computing, communicating, and controlling devices. Multipliers are used majorly in the areas of digital signal and image processing, central processing unit (CPU) of the computers, high-performance and parallel scientific computing, machine learning, physical layer design of the communication equipment, etc. The predominant presence and increasing demand for low-power, low-cost, and high-performance digital hardware led to this work of developing optimized multiplier designs. Two optimized designs are proposed in this work. One is an optimized 8 x 8 Booth multiplier architecture which is implemented using 32nm CMOS technology. Synthesis (pre-layout) and post-layout results show that the delay is reduced by 24.7% and 25.6% respectively, the area is reduced by 5.5% and 15% respectively, the power consumption is reduced by 21.5% and 26.6% respectively, and the area-delay-product is reduced by 28.8% and 36.8% respectively when compared to the performance results obtained for the state-of-the-art 8 x 8 Booth multiplier designed using 32nm CMOS technology with 1.05 V supply voltage at 500 MHz input frequency. Another is a novel radix-8 structure with 3-bit grouping to reduce the number of partial products along with the effective partial product reduction schemes for 8 x 8, 16 x 16, 32 x 32, and 64 x 64 signed multipliers. Comparing the performance results of the (synthesized, post-layout) designs of sizes 32 x 32, and 64 x 64 based on the simple novel radix-8 structure with the estimated performance measurements for the optimized Booth multiplier design presented in this work, reduction in delay by (2.64%, 0.47%) and (2.74%, 18.04%) respectively, and reduction in area-delay-product by (12.12%, -5.17%) and (17.82%, 12.91%) respectively can be observed. With the use of the higher radix structure, delay, area, and power consumption can be further reduced. Appropriate adder deployment, further exploring the optimized grouping or compression strategies, and applying more low-power design techniques such as power-gating, multi-Vt MOS transistor utilization, multi-VDD domain creation, etc., help, along with the higher radix structures, realizing the more efficient multiplier designs

A Reconfigurable Digital Multiplier and 4:2 Compressor Cells Design

With the continually growing use of portable computing devices and increasingly complex software applications, there is a constant push for low power high speed circuitry to support this technology. Because of the high usage and large complex circuitry required to carry out arithmetic operations used in applications such as digital signal processing, there has been a great focus on increasing the efficiency of computer arithmetic circuitry. A key player in the realm of computer arithmetic is the digital multiplier and because of its size and power consumption, it has moved to the forefront of today\u27s research. A digital reconfigurable multiplier architecture will be introduced. Regulated by a 2-bit control signal, the multiplier is capable of double and single precision multiplication, as well as fault tolerant and dual throughput single precision execution. The architecture proposed in this thesis is centered on a recursive multiplication algorithm, where a large multiplication is carried out using recursions of simpler submultiplier modules. Within each sub-multiplier module, instead of carry save adder arrays, 4:2 compressor rows are utilized for partial product reduction, which present greater efficiency, thus result in lower delay and power consumption of the whole multiplier. In addition, a study of various digital logic circuit styles are initially presented, and then three different designs of 4:2 compressor in Domino Logic are presented and simulation results confirm the property of proposed design in terms of delay, power consumption and operation frequenc

A Study on Efficient Designs of Approximate Arithmetic Circuits

Approximate computing is a popular field where accuracy is traded with energy. It can benefit applications such as multimedia, mobile computing and machine learning which are inherently error resilient. Error introduced in these applications to a certain degree is beyond human perception. This flexibility can be exploited to design area, delay and power efficient architectures. However, care must be taken on how approximation compromises the correctness of results. This research work aims to provide approximate hardware architectures with error metrics and design metrics analyzed and their effects in image processing applications. Firstly, we study and propose unsigned array multipliers based on probability statistics and with approximate 4-2 compressors, full adders and half adders. This work deals with a new design approach for approximation of multipliers. The partial products of the multiplier are altered to introduce varying probability terms. Logic complexity of approximation is varied for the accumulation of altered partial products based on their probability. The proposed approximation is utilized in two variants of 16-bit multipliers. Synthesis results reveal that two proposed multipliers achieve power savings of 72% and 38% respectively compared to an exact multiplier. They have better precision when compared to existing approximate multipliers. Mean relative error distance (MRED) figures are as low as 7.6% and 0.02% for the proposed approximate multipliers, which are better than the previous state-of-the-art works. Performance of the proposed multipliers is evaluated with geometric mean filtering application, where one of the proposed models achieves the highest peak signal to noise ratio (PSNR). Second, approximation is proposed for signed Booth multiplication. Approximation is introduced in partial product generation and partial product accumulation circuits. In this work, three multipliers (ABM-M1, ABM-M2, and ABM-M3) are proposed in which the modified Booth algorithm is approximated. In all three designs, approximate Booth partial product generators are designed with different variations of approximation. The approximations are performed by reducing the logic complexity of the Booth partial product generator, and the accumulation of partial products is slightly modified to improve circuit performance. Compared to the exact Booth multiplier, ABM-M1 achieves up to 15% reduction in power consumption with an MRED value of 7.9 × 10-4. ABM-M2 has power savings of up to 60% with an MRED of 1.1 × 10-1. ABM-M3 has power savings of up to 50% with an MRED of 3.4 × 10-3. Compared to existing approximate Booth multipliers, the proposed multipliers ABM-M1 and ABM-M3 achieve up to a 41% reduction in power consumption while exhibiting very similar error metrics. Image multiplication and matrix multiplication are used as case studies to illustrate the high performance of the proposed approximate multipliers. Third, distributed arithmetic based sum of products units approximation is analyzed. Sum of products units are key elements in many digital signal processing applications. Three approximate sum of products models which are based on distributed arithmetic are proposed. They are designed for different levels of accuracy. First model of approximate sum of products achieves an improvement up to 64% on area and 70% on power, when compared to conventional unit. Other two models provide an improvement of 32% and 48% on area and 54% and 58% on power, respectively, with a reduced error rate compared to the first model. Third model achieves MRED and normalized mean error distance (NMED) as low as 0.05% and 0.009%. Performance of approximate units is evaluated with a noisy image smoothing application, where the proposed models are capable of achieving higher PSNR than existing state of the art techniques. Fourth, approximation is applied in division architecture. Two approximation models are proposed for restoring divider. In the first design, approximation is performed at circuit level, where approximate divider cells are utilized in place of exact ones by simplifying the logic equations. In the second model, restoring divider is analyzed strategically and number of restoring divider cells are reduced by finding the portions of divisor and dividend with significant information. An approximation factor $p$ is used in both designs. In model 1, the design with p=8 has a 58% reduction in both area and power consumption compared to exact design, with a Q-MRED of 1.909 × 10-2 and Q-NMED of 0.449 × 10-2. The second model with an approximation factor p=4 has 54% area savings and 62% power savings compared to exact design. The proposed models are found to have better error metrics compared to existing designs, with better performance at similar error values. A change detection image processing application is used for real time assessment of proposed and existing approximate dividers and one of the models achieves a PSNR of 54.27 dB

A Synthesizable single-cycle multiply-accumulator

The multiplication and multiply-accumulate operations are expensive to implement in hardware for Digital Signal Processing, video, and graphics applications. A standard multiply-accumulator has three inputs and a single output that is equal to the product of two of its inputs added to the third input. For some applications it is desirable for a multiply-accumulator to have two outputs; one output that is the product of the first two inputs, and a second output that is the multiply-accumulate result. The goal of this thesis is to investigate algorithms and architectures used to design multipliers and multiply-accumulators, and to create a multiply-accumulator that computes both outputs in a single clock cycle. Often times in high speed designs the most time-consuming operations are pipelined to meet the system timing requirements. If the multiply-accumulate computation can be reduced to a single-cycle operation the overall processor performance can be improved for many applications. A multiply-accumulator with two outputs can be created using a combination of standard multiply, add, or multiply-accumulate components. Using these components, a multiplier and a multiply-accumulator can be used to produce the outputs in the most time-efficient manner. A multiplier and an adder will result in a smaller design with a larger worst-case delay. Therefore, the goal is to create a multiply-accumulator that is comparable in speed, but requires less area than a design using an industry standard multiplier and multiply-accumulator

Analysis and implementation of decimal arithmetic hardware in nanometer CMOS technology

Scope and Method of Study: In today's society, decimal arithmetic is growing considerably in importance given its relevance in financial and commercial applications. Decimal calculations on binary hardware significantly impact performance mainly because most systems utilize software to emulate decimal calculations. The introduction of dedicated decimal hardware on the other hand promises the ability to improve performance by two or three orders of magnitude. The founding blocks of binary arithmetic are studied and applied to the development of decimal arithmetic hardware. New findings are contrasted with existent implementations and validated through extensive simulation.Findings and Conclusions: New architectures and a significant study of decimal arithmetic was developed and implemented. The architectures proposed include an IEEE-754 current revision draft compliant floating-point comparator, a study on decimal division, partial product reduction schemes using decimal compressor trees and a final implementation of a decimal multiplier using advanced techniques for partial product generation. The results of each hardware implementation in nanometer technologies are weighed against existent propositions and show improvements upon area, delay, and power

THE DESIGN OF AN IC HALF PRECISION FLOATING POINT ARITHMETIC LOGIC UNIT

A 16 bit floating point (FP) Arithmetic Logic Unit (ALU) was designed and implemented in 0.35µm CMOS technology. Typical uses of the 16 bit FP ALU include graphics processors and embedded multimedia applications. The ALU of the modern microprocessors use a fused multiply add (FMA) design technique. An advantage of the FMA is to remove the need for a comparator which is required for a normal FP adder. The FMA consists of a multiplier, shifters, adders and rounding circuit. A fast multiplier based on the Wallace tree configuration was designed. The number of partial products was greatly reduced by the use of the modified booth encoder. The Wallace tree was chosen to reduce the number of reduction layers of partial products. The multiplier also involved the design of a pass transistor based 4:2 compressor. The average delay of the pass transistor based compressor was 55ps and was found to be 7 times faster than the full adder based 4:2 compressor. The shifters consist of separate left and right shifters using multiplexers. The shift amount is calculated using the exponents of the three operands. The addition operation is implemented using a carry skip adder (CSK). The average delay of the CSK was 1.05ns and was slower than the carry look ahead adder by about 400ps. The advantages of the CSK are reduced power, gate count and area when compared to the similar sized carry look ahead adder. The adder computes the addition of the multiplier result and the shifted value of the addend. In most modern computers, division is performed using software thereby eliminating the need for a separate hardware unit. FMA hardware unit was utilized to perform FP division. The FP divider uses the Newton Raphson algorithm to solve division by iteration. The initial approximated value with five bit accuracy was assumed to be pre-stored in cache memory and a separate clock cycle for cache read was assumed before the start of the FP division operation. In order to significantly reduce the area of the design, only one multiplier was used. Rounding to nearest technique was implemented using an 11 bit variable CSK adder. This is the best rounding technique when compared to other rounding techniques. In both the FMA and division, rounding was performed after the computation of the final result during the last clock cycle of operation. Testability analysis is performed for the multiplier which is the most complex and critical part of the FP ALU. The specific aim of testability was to ensure the correct operation of the multiplier and thus guarantee the correctness of the FMA circuit at the layout stage. The multiplier\u27s output was tested by identifying the minimal number of input vectors which toggle the inputs of the 4:2 compressors of the multiplier. The test vectors were identified in a semi automated manner using Perl scripting language. The multiplier was tested with a test set of thirty one vectors. The fault coverage of the multiplier was found to be 90.09%. The layout was implemented using IC station of Mentor Graphics CAD tool and resulted in a chip area of 1.96mm2. The specifications for basic arithmetic operations were met successfully. FP Division operation was completed within six clock cycles. The other arithmetic operations like FMA, FP addition, FP subtraction and FP multiplication were completed within three clock cycles

Null convention logic circuits for asynchronous computer architecture

For most of its history, computer architecture has been able to benefit from a rapid scaling in semiconductor technology, resulting in continuous improvements to CPU design. During that period, synchronous logic has dominated because of its inherent ease of design and abundant tools. However, with the scaling of semiconductor processes into deep sub-micron and then to nano-scale dimensions, computer architecture is hitting a number of roadblocks such as high power and increased process variability. Asynchronous techniques can potentially offer many advantages compared to conventional synchronous design, including average case vs. worse case performance, robustness in the face of process and operating point variability and the ready availability of high performance, fine grained pipeline architectures. Of the many alternative approaches to asynchronous design, Null Convention Logic (NCL) has the advantage that its quasi delay-insensitive behavior makes it relatively easy to set up complex circuits without the need for exhaustive timing analysis. This thesis examines the characteristics of an NCL based asynchronous RISC-V CPU and analyses the problems with applying NCL to CPU design. While a number of university and industry groups have previously developed small 8-bit microprocessor architectures using NCL techniques, it is still unclear whether these offer any real advantages over conventional synchronous design. A key objective of this work has been to analyse the impact of larger word widths and more complex architectures on NCL CPU implementations. The research commenced by re-evaluating existing techniques for implementing NCL on programmable devices such as FPGAs. The little work that has been undertaken previously on FPGA implementations of asynchronous logic has been inconclusive and seems to indicate that asynchronous systems cannot be easily implemented in these devices. However, most of this work related to an alternative technique called bundled data, which is not well suited to FPGA implementation because of the difficulty in controlling and matching delays in a 'bundle' of signals. On the other hand, this thesis clearly shows that such applications are not only possible with NCL, but there are some distinct advantages in being able to prototype complex asynchronous systems in a field-programmable technology such as the FPGA. A large part of the value of NCL derives from its architectural level behavior, inherent pipelining, and optimization opportunities such as the merging of register and combina- tional logic functions. In this work, a number of NCL multiplier architectures have been analyzed to reveal the performance trade-offs between various non-pipelined, 1D and 2D organizations. Two-dimensional pipelining can easily be applied to regular architectures such as array multipliers in a way that is both high performance and area-efficient. It was found that the performance of 2D pipelining for small networks such as multipliers is around 260% faster than the equivalent non-pipelined design. However, the design uses 265% more transistors so the methodology is mainly of benefit where performance is strongly favored over area. A pipelined 32bit x 32bit signed Baugh-Wooley multiplier with Wallace-Tree Carry Save Adders (CSA), which is representative of a real design used for CPUs and DSPs, was used to further explore this concept as it is faster and has fewer pipeline stages compared to the normal array multiplier using Ripple-Carry adders (RCA). It was found that 1D pipelining with ripple-carry chains is an efficient implementation option but becomes less so for larger multipliers, due to the completion logic for which the delay time depends largely on the number of bits involved in the completion network. The average-case performance of ripple-carry adders was explored using random input vectors and it was observed that it offers little advantage on the smaller multiplier blocks, but this particular timing characteristic of asynchronous design styles be- comes increasingly more important as word size grows. Finally, this research has resulted in the development of the first 32-Bit asynchronous RISC-V CPU core. Called the Redback RISC, the architecture is a structure of pipeline rings composed of computational oscillations linked with flow completeness relationships. It has been written using NELL, a commercial description/synthesis tool that outputs standard Verilog. The Redback has been analysed and compared to two approximately equivalent industry standard 32-Bit synchronous RISC-V cores (PicoRV32 and Rocket) that are already fabricated and used in industry. While the NCL implementation is larger than both commercial cores it has similar performance and lower power compared to the PicoRV32. The implementation results were also compared against an existing NCL design tool flow (UNCLE), which showed how much the results of these implementation strategies differ. The Redback RISC has achieved similar level of throughput and 43% better power and 34% better energy compared to one of the synchronous cores with the same benchmark test and test condition such as input sup- ply voltage. However, it was shown that area is the biggest drawback for NCL CPU design. The core is roughly 2.5× larger than synchronous designs. On the other hand its area is still 2.9× smaller than previous designs using UNCLE tools. The area penalty is largely due to the unavoidable translation into a dual-rail topology when using the standard NCL cell library

Energy-efficient embedded machine learning algorithms for smart sensing systems

Embedded autonomous electronic systems are required in numerous application domains such as Internet of Things (IoT), wearable devices, and biomedical systems. Embedded electronic systems usually host sensors, and each sensor hosts multiple input channels (e.g., tactile, vision), tightly coupled to the electronic computing unit (ECU). The ECU extracts information by often employing sophisticated methods, e.g., Machine Learning. However, embedding Machine Learning algorithms poses essential challenges in terms of hardware resources and energy consumption because of: 1) the high amount of data to be processed; 2) computationally demanding methods. Leveraging on the trade-off between quality requirements versus computational complexity and time latency could reduce the system complexity without affecting the performance. The objectives of the thesis are to develop: 1) energy-efficient arithmetic circuits outperforming state of the art solutions for embedded machine learning algorithms, 2) an energy-efficient embedded electronic system for the \u201celectronic-skin\u201d (e-skin) application. As such, this thesis exploits two main approaches: Approximate Computing: In recent years, the approximate computing paradigm became a significant major field of research since it is able to enhance the energy efficiency and performance of digital systems. \u201cApproximate Computing\u201d(AC) turned out to be a practical approach to trade accuracy for better power, latency, and size . AC targets error-resilient applications and offers promising benefits by conserving some resources. Usually, approximate results are acceptable for many applications, e.g., tactile data processing,image processing , and data mining ; thus, it is highly recommended to take advantage of energy reduction with minimal variation in performance . In our work, we developed two approximate multipliers: 1) the first one is called \u201cMETA\u201d multiplier and is based on the Error Tolerant Adder (ETA), 2) the second one is called \u201cApproximate Baugh-Wooley(BW)\u201d multiplier where the approximations are implemented in the generation of the partial products. We showed that the proposed approximate arithmetic circuits could achieve a relevant reduction in power consumption and time delay around 80.4% and 24%, respectively, with respect to the exact BW multiplier. Next, to prove the feasibility of AC in real world applications, we explored the approximate multipliers on a case study as the e-skin application. The e-skin application is defined as multiple sensing components, including 1) structural materials, 2) signal processing, 3) data acquisition, and 4) data processing. Particularly, processing the originated data from the e-skin into low or high-level information is the main problem to be addressed by the embedded electronic system. Many studies have shown that Machine Learning is a promising approach in processing tactile data when classifying input touch modalities. In our work, we proposed a methodology for evaluating the behavior of the system when introducing approximate arithmetic circuits in the main stages (i.e., signal and data processing stages) of the system. Based on the proposed methodology, we first implemented the approximate multipliers on the low-pass Finite Impulse Response (FIR) filter in the signal processing stage of the application. We noticed that the FIR filter based on (Approx-BW) outperforms state of the art solutions, while respecting the tradeoff between accuracy and power consumption, with an SNR degradation of 1.39dB. Second, we implemented approximate adders and multipliers respectively into the Coordinate Rotational Digital Computer (CORDIC) and the Singular Value Decomposition (SVD) circuits; since CORDIC and SVD take a significant part of the computationally expensive Machine Learning algorithms employed in tactile data processing. We showed benefits of up to 21% and 19% in power reduction at the cost of less than 5% accuracy loss for CORDIC and SVD circuits when scaling the number of approximated bits. 2) Parallel Computing Platforms (PCP): Exploiting parallel architectures for near-threshold computing based on multi-core clusters is a promising approach to improve the performance of smart sensing systems. In our work, we exploited a novel computing platform embedding a Parallel Ultra Low Power processor (PULP), called \u201cMr. Wolf,\u201d for the implementation of Machine Learning (ML) algorithms for touch modalities classification. First, we tested the ML algorithms at the software level; for RGB images as a case study and tactile dataset, we achieved accuracy respectively equal to 97% and 83.5%. After validating the effectiveness of the ML algorithm at the software level, we performed the on-board classification of two touch modalities, demonstrating the promising use of Mr. Wolf for smart sensing systems. Moreover, we proposed a memory management strategy for storing the needed amount of trained tensors (i.e., 50 trained tensors for each class) in the on-chip memory. We evaluated the execution cycles for Mr. Wolf using a single core, 2 cores, and 3 cores, taking advantage of the benefits of the parallelization. We presented a comparison with the popular low power ARM Cortex-M4F microcontroller employed, usually for battery-operated devices. We showed that the ML algorithm on the proposed platform runs 3.7 times faster than ARM Cortex M4F (STM32F40), consuming only 28 mW. The proposed platform achieves 15 7 better energy efficiency than the classification done on the STM32F40, consuming 81mJ per classification and 150 pJ per operation