Robust low-power digital circuit design in nano-CMOS technologies

Device scaling has resulted in large scale integrated, high performance, low-power, and low cost systems. However the move towards sub-100 nm technology nodes has increased variability in device characteristics due to large process variations. Variability has severe implications on digital circuit design by causing timing uncertainties in combinational circuits, degrading yield and reliability of memory elements, and increasing power density due to slow scaling of supply voltage. Conventional design methods add large pessimistic safety margins to mitigate increased variability, however, they incur large power and performance loss as the combination of worst cases occurs very rarely. In-situ monitoring of timing failures provides an opportunity to dynamically tune safety margins in proportion to on-chip variability that can significantly minimize power and performance losses. We demonstrated by simulations two delay sensor designs to detect timing failures in advance that can be coupled with different compensation techniques such as voltage scaling, body biasing, or frequency scaling to avoid actual timing failures. Our simulation results using 45 nm and 32 nm technology BSIM4 models indicate significant reduction in total power consumption under temperature and statistical variations. Future work involves using dual sensing to avoid useless voltage scaling that incurs a speed loss. SRAM cache is the first victim of increased process variations that requires handcrafted design to meet area, power, and performance requirements. We have proposed novel 6 transistors (6T), 7 transistors (7T), and 8 transistors (8T)-SRAM cells that enable variability tolerant and low-power SRAM cache designs. Increased sense-amplifier offset voltage due to device mismatch arising from high variability increases delay and power consumption of SRAM design. We have proposed two novel design techniques to reduce offset voltage dependent delays providing a high speed low-power SRAM design. Increasing leakage currents in nano-CMOS technologies pose a major challenge to a low-power reliable design. We have investigated novel segmented supply voltage architecture to reduce leakage power of the SRAM caches since they occupy bulk of the total chip area and power. Future work involves developing leakage reduction methods for the combination logic designs including SRAM peripherals

Design of variability compensation architectures of digital circuits with adaptive body bias

The most critical concern in circuit is to achieve high level of performance with very tight power constraint. As the high performance circuits moved beyond 45nm technology one of the major issues is the parameter variation i.e. deviation in process, temperature and voltage (PVT) values from nominal specifications. A key process parameter subject to variation is the transistor threshold voltage (Vth) which impacts two important parameters: frequency and leakage power. Although the degradation can be compensated by the worstcase scenario based over-design approach, it induces remarkable power and performance overhead which is undesirable in tightly constrained designs. Dynamic voltage scaling (DVS) is a more power efficient approach, however its coarse granularity implies difficulty in handling fine grained variations. These factors have contributed to the growing interest in power aware robust circuit design. We propose a variability compensation architecture with adaptive body bias, for low power applications using 28nm FDSOI technology. The basic approach is based on a dynamic prediction and prevention of possible circuit timing errors. In our proposal we are using a Canary logic technique that enables the typical-case design. The body bias generation is based on a DLL type method which uses an external reference generator and voltage controlled delay line (VCDL) to generate the forward body bias (FBB) control signals. The adaptive technique is used for dynamic detection and correction of path failures in digital designs due to PVT variations. Instead of tuning the supply voltage, the key idea of the design approach is to tune the body bias voltage bymonitoring the error rate during operation. The FBB increases operating speed with an overhead in leakage power

Reliable chip design from low powered unreliable components

The pace of technological improvement of the semiconductor market is driven by Moore’s Law, enabling chip transistor density to double every two years. The transistors would continue to decline in cost and size but increase in power. The continuous transistor scaling and extremely lower power constraints in modern Very Large Scale Integrated(VLSI) chips can potentially supersede the benefits of the technology shrinking due to reliability issues. As VLSI technology scales into nanoscale regime, fundamental physical limits are approached, and higher levels of variability, performance degradation, and higher rates of manufacturing defects are experienced. Soft errors, which traditionally affected only the memories, are now also resulting in logic circuit reliability degradation. A solution to these limitations is to integrate reliability assessment techniques into the Integrated Circuit(IC) design flow. This thesis investigates four aspects of reliability driven circuit design: a)Reliability estimation; b) Reliability optimization; c) Fault-tolerant techniques, and d) Delay degradation analysis. To guide the reliability driven synthesis and optimization of combinational circuits, highly accurate probability based reliability estimation methodology christened Conditional Probabilistic Error Propagation(CPEP) algorithm is developed to compute the impact of gate failures on the circuit output. CPEP guides the proposed rewriting based logic optimization algorithm employing local transformations. The main idea behind this methodology is to replace parts of the circuit with functionally equivalent but more reliable counterparts chosen from a precomputed subset of Negation-Permutation-Negation(NPN) classes of 4-variable functions. Cut enumeration and Boolean matching driven by reliability-aware optimization algorithm are used to identify the best possible replacement candidates. Experiments on a set of MCNC benchmark circuits and 8051 functional microcontroller units indicate that the proposed framework can achieve up to 75% reduction of output error probability. On average, about 14% SER reduction is obtained at the expense of very low area overhead of 6.57% that results in 13.52% higher power consumption. The next contribution of the research describes a novel methodology to design fault tolerant circuitry by employing the error correction codes known as Codeword Prediction Encoder(CPE). Traditional fault tolerant techniques analyze the circuit reliability issue from a static point of view neglecting the dynamic errors. In the context of communication and storage, the study of novel methods for reliable data transmission under unreliable hardware is an increasing priority. The idea of CPE is adapted from the field of forward error correction for telecommunications focusing on both encoding aspects and error correction capabilities. The proposed Augmented Encoding solution consists of computing an augmented codeword that contains both the codeword to be transmitted on the channel and extra parity bits. A Computer Aided Development(CAD) framework known as CPE simulator is developed providing a unified platform that comprises a novel encoder and fault tolerant LDPC decoders. Experiments on a set of encoders with different coding rates and different decoders indicate that the proposed framework can correct all errors under specific scenarios. On average, about 1000 times improvement in Soft Error Rate(SER) reduction is achieved. Last part of the research is the Inverse Gaussian Distribution(IGD) based delay model applicable to both combinational and sequential elements for sub-powered circuits. The Probability Density Function(PDF) based delay model accurately captures the delay behavior of all the basic gates in the library database. The IGD model employs these necessary parameters, and the delay estimation accuracy is demonstrated by evaluating multiple circuits. Experiments results indicate that the IGD based approach provides a high matching against HSPICE Monte Carlo simulation results, with an average error less than 1.9% and 1.2% for the 8-bit Ripple Carry Adder(RCA), and 8-bit De-Multiplexer(DEMUX) and Multiplexer(MUX) respectively

Timing speculation and adaptive reliable overclocking techniques for aggressive computer systems

Computers have changed our lives beyond our own imagination in the past several decades. The continued and progressive advancements in VLSI technology and numerous micro-architectural innovations have played a key role in the design of spectacular low-cost high performance computing systems that have become omnipresent in today\u27s technology driven world. Performance and dependability have become key concerns as these ubiquitous computing machines continue to drive our everyday life. Every application has unique demands, as they run in diverse operating environments. Dependable, aggressive and adaptive systems improve efficiency in terms of speed, reliability and energy consumption. Traditional computing systems run at a fixed clock frequency, which is determined by taking into account the worst-case timing paths, operating conditions, and process variations. Timing speculation based reliable overclocking advocates going beyond worst-case limits to achieve best performance while not avoiding, but detecting and correcting a modest number of timing errors. The success of this design methodology relies on the fact that timing critical paths are rarely exercised in a design, and typical execution happens much faster than the timing requirements dictated by worst-case design methodology. Better-than-worst-case design methodology is advocated by several recent research pursuits, which exploit dependability techniques to enhance computer system performance. In this dissertation, we address different aspects of timing speculation based adaptive reliable overclocking schemes, and evaluate their role in the design of low-cost, high performance, energy efficient and dependable systems. We visualize various control knobs in the design that can be favorably controlled to ensure different design targets. As part of this research, we extend the SPRIT3E, or Superscalar PeRformance Improvement Through Tolerating Timing Errors, framework, and characterize the extent of application dependent performance acceleration achievable in superscalar processors by scrutinizing the various parameters that impact the operation beyond worst-case limits. We study the limitations imposed by short-path constraints on our technique, and present ways to exploit them to maximize performance gains. We analyze the sensitivity of our technique\u27s adaptiveness by exploring the necessary hardware requirements for dynamic overclocking schemes. Experimental analysis based on SPEC2000 benchmarks running on a SimpleScalar Alpha processor simulator, augmented with error rate data obtained from hardware simulations of a superscalar processor, are presented. Even though reliable overclocking guarantees functional correctness, it leads to higher power consumption. As a consequence, reliable overclocking without considering on-chip temperatures will bring down the lifetime reliability of the chip. In this thesis, we analyze how reliable overclocking impacts the on-chip temperature of a microprocessor and evaluate the effects of overheating, due to such reliable dynamic frequency tuning mechanisms, on the lifetime reliability of these systems. We then evaluate the effect of performing thermal throttling, a technique that clamps the on-chip temperature below a predefined value, on system performance and reliability. Our study shows that a reliably overclocked system with dynamic thermal management achieves 25% performance improvement, while lasting for 14 years when being operated within 353K. Over the past five decades, technology scaling, as predicted by Moore\u27s law, has been the bedrock of semiconductor technology evolution. The continued downscaling of CMOS technology to deep sub-micron gate lengths has been the primary reason for its dominance in today\u27s omnipresent silicon microchips. Even as the transition to the next technology node is indispensable, the initial cost and time associated in doing so presents a non-level playing field for the competitors in the semiconductor business. As part of this thesis, we evaluate the capability of speculative reliable overclocking mechanisms to maximize performance at a given technology level. We evaluate its competitiveness when compared to technology scaling, in terms of performance, power consumption, energy and energy delay product. We present a comprehensive comparison for integer and floating point SPEC2000 benchmarks running on a simulated Alpha processor at three different technology nodes in normal and enhanced modes. Our results suggest that adopting reliable overclocking strategies will help skip a technology node altogether, or be competitive in the market, while porting to the next technology node. Reliability has become a serious concern as systems embrace nanometer technologies. In this dissertation, we propose a novel fault tolerant aggressive system that combines soft error protection and timing error tolerance. We replicate both the pipeline registers and the pipeline stage combinational logic. The replicated logic receives its inputs from the primary pipeline registers while writing its output to the replicated pipeline registers. The organization of redundancy in the proposed Conjoined Pipeline system supports overclocking, provides concurrent error detection and recovery capability for soft errors, intermittent faults and timing errors, and flags permanent silicon defects. The fast recovery process requires no checkpointing and takes three cycles. Back annotated post-layout gate-level timing simulations, using 45nm technology, of a conjoined two-stage arithmetic pipeline and a conjoined five-stage DLX pipeline processor, with forwarding logic, show that our approach, even under a severe fault injection campaign, achieves near 100% fault coverage and an average performance improvement of about 20%, when dynamically overclocked

Improving the Reliability of Microprocessors under BTI and TDDB Degradations

Reliability is a fundamental challenge for current and future microprocessors with advanced nanoscale technologies. With smaller gates, thinner dielectric and higher temperature microprocessors are vulnerable under aging mechanisms such as Bias Temperature Instability (BTI) and Temperature Dependent Dielectric Breakdown (TDDB). Under continuous stress both parametric and functional errors occur, resulting compromised microprocessor lifetime. In this thesis, based on the thorough study on BTI and TDDB mechanisms, solutions are proposed to mitigating the aging processes on memory based and random logic structures in modern out-of-order microprocessors. A large area of processor core is occupied by memory based structure that is vulnerable to BTI induced errors. The problem is exacerbated when PBTI degradation in NMOS is as severe as NBTI in PMOS in high-k metal gate technology. Hence a novel design is proposed to recover 4 internal gates within a SRAM cell simultaneously to mitigate both NBTI and PBTI effects. This technique is applied to both the L2 cache banks and the busy function units with storage cells in out-of-order pipeline in two different ways. For the L2 cache banks, redundant cache bank is added exclusively for proactive recovery rotation. For the critical and busy function units in out-of-order pipelines, idle cycles are exploited at per-buffer-entry level. Different from memory based structures, combinational logic structures such as function units in execution stage can not use low overhead redundancy to tolerate errors due to their irregular structure. A design framework that aims to improve the reliability of the vulnerable functional units of a processor core is designed and implemented. The approach is designing a generic function unit (GFU) that can be reconfigured to replace a particular functional unit (FU) while it is being recovered for improved lifetime. Although flexible, the GFU is slower than the original target FUs. So GFU is carefully designed so as to minimize the performance loss when it is in-use. More schemes are also designed to avoid using the GFU on performance critical paths of a program execution

Empirical timing analysis of CPUs and delay fault tolerant design using partial redundancy

The operating clock frequency is determined by the longest signal propagation delay, setup/hold time, and timing margin. These are becoming less predictable with the increasing design complexity and process miniaturization. The difficult challenge is then to ensure that a device operating at its clock frequency is error-free with quantifiable assurance. Effort at device-level engineering will not suffice for these circuits exhibiting wide process variation and heightened sensitivities to operating condition stress. Logic-level redress of this issue is a necessity and we propose a design-level remedy for this timing-uncertainty problem. The aim of the design and analysis approaches presented in this dissertation is to provide framework, SABRE, wherein an increased operating clock frequency can be achieved. The approach is a combination of analytical modeling, experimental analy- sis, hardware /time-redundancy design, exception handling and recovery techniques. Our proposed design replicates only a necessary part of the original circuit to avoid high hardware overhead as in triple-modular-redundancy (TMR). The timing-critical combinational circuit is path-wise partitioned into two sections. The combinational circuits associated with long paths are laid out without any intrusion except for the fan-out connections from the first section of the circuit to a replicated second section of the combinational circuit. Thus only the second section of the circuit is replicated. The signals fanning out from the first section are latches, and thus are far shorter than the paths spanning the entire combinational circuit. The replicated circuit is timed at a subsequent clock cycle to ascertain relaxed timing paths. This insures that the likelihood of mistiming due to stress or process variation is eliminated. During the subsequent clock cycle, the outcome of the two logically identical, yet time-interleaved, circuit outputs are compared to detect faults. When a fault is detected, the retry sig- nal is triggered and the dynamic frequency-step-down takes place before a pipe flush, and retry is issued. The significant timing overhead associated with the retry is offset by the rarity of the timing violation events. Simulation results on ISCAS Benchmark circuits show that 10% of clock frequency gain is possible with 10 to 20 % of hardware overhead of replicated timing-critical circuit

Injecting Intermittent Faults for the Dependability Assessment of a Fault-Tolerant Microcomputer System

© 2016 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes, creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works.As scaling is more and more aggressive, intermittent faults are increasing their importance in current deep submicron complementary metal-oxide-semiconductor (CMOS) technologies. This work shows the dependability assessment of a fault-tol- erant computer system against intermittent faults. The applied methodology lies in VHDL-based fault injection, which allows the assessment in early design phases, together with a high level of observability and controllability. The evaluated system is a duplex microcontroller system with cold stand-by sparing. A wide set of intermittent fault models have been injected, and from the simulation traces, coverages and latencies have been measured. Markov models for this system have been generated and some dependability functions, such as reliability and safety, have been calculated. From these results, some enhancements of detection and recovery mechanisms have been suggested. The methodology presented is general to any fault-tolerant computer system.This work was supported in part by the Universitat Politecnica de Valencia under the Research Project SP20120806, and in part by the Spanish Government under the Research Project TIN2012-38308-C02-01. Associate Editor: J. Shortle.Gil Tomás, DA.; Gracia Morán, J.; Baraza Calvo, JC.; Saiz Adalid, LJ.; Gil Vicente, PJ. (2016). Injecting Intermittent Faults for the Dependability Assessment of a Fault-Tolerant Microcomputer System. IEEE Transactions on Reliability. 65(2):648-661. https://doi.org/10.1109/TR.2015.2484058S64866165

PRITEXT: Processor Reliability Improvement Through Exercise Technique

With continuous improvements in CMOS technology, transistor sizes are shrinking aggressively every year. Unfortunately, such deep submicron process technologies are severely degraded by several wearout mechanisms which lead to prolonged operational stress and failure. Negative Bias Temperature Instability (NBTI) is a prominent failure mechanism which degrades the reliability of current semiconductor devices. Improving reliability of processors is necessary for ensuring long operational lifetime which obviates the necessity of mitigating the physical wearout mechanisms. NBTI severely degrades the performance of PMOS transistors in a circuit, when negatively biased, by increasing the threshold voltage leading to critical timing failures over operational lifetime. A lack of activity among the PMOS transistors for long duration leads to a steady increase in threshold voltage Vth. Interestingly, NBTI stress can be recovered by removing the negative bias using appropriate input vectors. Exercising the dormant critical components in the Processor has been proved to reduce the NBTI stress. We use a novel methodology to generate a minimal set of deterministic input vectors which we show to be effective in reducing the NBTI wearout in a superscalar processor core. We then propose and evaluate a new technique PRITEXT, which uses these input vectors in exercise mode to effectively reduce the NBTI stress and improve the operational lifetime of superscalar processors. PRITEXT, which uses Input Vector Control, leads to a 4.5x lifetime improvement of superscalar processor on average with a maximum lifetime improvement of 12.7x

Techniques for Improving Security and Trustworthiness of Integrated Circuits

The integrated circuit (IC) development process is becoming increasingly vulnerable to malicious activities because untrusted parties could be involved in this IC development flow. There are four typical problems that impact the security and trustworthiness of ICs used in military, financial, transportation, or other critical systems: (i) Malicious inclusions and alterations, known as hardware Trojans, can be inserted into a design by modifying the design during GDSII development and fabrication. Hardware Trojans in ICs may cause malfunctions, lower the reliability of ICs, leak confidential information to adversaries or even destroy the system under specifically designed conditions. (ii) The number of circuit-related counterfeiting incidents reported by component manufacturers has increased significantly over the past few years with recycled ICs contributing the largest percentage of the total reported counterfeiting incidents. Since these recycled ICs have been used in the field before, the performance and reliability of such ICs has been degraded by aging effects and harsh recycling process. (iii) Reverse engineering (RE) is process of extracting a circuit’s gate-level netlist, and/or inferring its functionality. The RE causes threats to the design because attackers can steal and pirate a design (IP piracy), identify the device technology, or facilitate other hardware attacks. (iv) Traditional tools for uniquely identifying devices are vulnerable to non-invasive or invasive physical attacks. Securing the ID/key is of utmost importance since leakage of even a single device ID/key could be exploited by an adversary to hack other devices or produce pirated devices. In this work, we have developed a series of design and test methodologies to deal with these four challenging issues and thus enhance the security, trustworthiness and reliability of ICs. The techniques proposed in this thesis include: a path delay fingerprinting technique for detection of hardware Trojans, recycled ICs, and other types counterfeit ICs including remarked, overproduced, and cloned ICs with their unique identifiers; a Built-In Self-Authentication (BISA) technique to prevent hardware Trojan insertions by untrusted fabrication facilities; an efficient and secure split manufacturing via Obfuscated Built-In Self-Authentication (OBISA) technique to prevent reverse engineering by untrusted fabrication facilities; and a novel bit selection approach for obtaining the most reliable bits for SRAM-based physical unclonable function (PUF) across environmental conditions and silicon aging effects

Fault-tolerant fpga for mission-critical applications.

One of the devices that play a great role in electronic circuits design, specifically safety-critical design applications, is Field programmable Gate Arrays (FPGAs). This is because of its high performance, re-configurability and low development cost. FPGAs are used in many applications such as data processing, networks, automotive, space and industrial applications. Negative impacts on the reliability of such applications result from moving to smaller feature sizes in the latest FPGA architectures. This increases the need for fault-tolerant techniques to improve reliability and extend system lifetime of FPGA-based applications. In this thesis, two fault-tolerant techniques for FPGA-based applications are proposed with a built-in fault detection region. A low cost fault detection scheme is proposed for detecting faults using the fault detection region used in both schemes. The fault detection scheme primarily detects open faults in the programmable interconnect resources in the FPGAs. In addition, Stuck-At faults and Single Event Upsets (SEUs) fault can be detected. For fault recovery, each scheme has its own fault recovery approach. The first approach uses a spare module and a 2-to-1 multiplexer to recover from any fault detected. On the other hand, the second approach recovers from any fault detected using the property of Partial Reconfiguration (PR) in the FPGAs. It relies on identifying a Partially Reconfigurable block (P_b) in the FPGA that is used in the recovery process after the first faulty module is identified in the system. This technique uses only one location to recover from faults in any of the FPGA’s modules and the FPGA interconnects. Simulation results show that both techniques can detect and recover from open faults. In addition, Stuck-At faults and Single Event Upsets (SEUs) fault can also be detected. Finally, both techniques require low area overhead