9,118 research outputs found
A 0.1â5.0âŻGHz flexible SDR receiver with digitally assisted calibration in 65âŻnm CMOS
© 2017 Elsevier Ltd. All rights reserved.A 0.1â5.0 GHz flexible software-defined radio (SDR) receiver with digitally assisted calibration is presented, employing a zero-IF/low-IF reconfigurable architecture for both wideband and narrowband applications. The receiver composes of a main-path based on a current-mode mixer for low noise, a high linearity sub-path based on a voltage-mode passive mixer for out-of-band rejection, and a harmonic rejection (HR) path with vector gain calibration. A dual feedback LNA with â8â shape nested inductor structure, a cascode inverter-based TCA with miller feedback compensation, and a class-AB full differential Op-Amp with Miller feed-forward compensation and QFG technique are proposed. Digitally assisted calibration methods for HR, IIP2 and image rejection (IR) are presented to maintain high performance over PVT variations. The presented receiver is implemented in 65 nm CMOS with 5.4 mm2 core area, consuming 9.6â47.4 mA current under 1.2 V supply. The receiver main path is measured with +5 dB m/+5dBm IB-IIP3/OB-IIP3 and +61dBm IIP2. The sub-path achieves +10 dB m/+18dBm IB-IIP3/OB-IIP3 and +62dBm IIP2, as well as 10 dB RF filtering rejection at 10 MHz offset. The HR-path reaches +13 dB m/+14dBm IB-IIP3/OB-IIP3 and 62/66 dB 3rd/5th-order harmonic rejection with 30â40 dB improvement by the calibration. The measured sensitivity satisfies the requirements of DVB-H, LTE, 802.11 g, and ZigBee.Peer reviewedFinal Accepted Versio
Voltage-Mode Multifunction Biquadratic Filters Using New Ultra-Low-Power Differential Difference Current Conveyors
This paper presents two low-power voltage-mode multifunction biquadratic filters using differential difference current conveyors. Each proposed circuit employs three differential difference current conveyors, two grounded capacitors and two grounded resistors. The low-voltage ultra-low-power differential difference current conveyor is used to provide low-power consumption of the proposed filters. By appropriately connecting the input and output terminals, the proposed filters can provide low-pass, band-pass, high-pass, band-stop and all-pass voltage responses at high-input terminals, which is a desirable feature for voltage-mode operations. The natural frequency and the quality factor can be orthogonally set by adjusting the circuit components. For realizing all the filter responses, no inverting-type input signal requirements as well as no component-matching conditional requirements are imposed. The incremental parameter sensitivities are also low. The characteristics of the proposed circuits are simulated by using PSPICE simulators to confirm the presented theory
The Brazilian Tunable Filter Imager for the SOAR telescope
This paper presents a new Tunable Filter Instrument for the SOAR telescope.
The Brazilian Tunable Filter Imager (BTFI) is a versatile, new technology,
tunable optical imager to be used in seeing-limited mode and at higher spatial
fidelity using the SAM Ground-Layer Adaptive Optics facility at the SOAR
telescope. The instrument opens important new science capabilities for the SOAR
community, from studies of the centers of nearby galaxies and the insterstellar
medium to statistical cosmological investigations. The BTFI takes advantage of
three new technologies. The imaging Bragg Tunable Filter concept utilizes
Volume Phase Holographic Gratings in a double-pass configuration, as a tunable
filter, while a new Fabry-Perot (FP) concept involves technologies which allow
a single FP etalon to act over a large range of interference orders and
spectral resolutions. Both technologies will be in the same instrument.
Spectral resolutions spanning the range between 25 and 30,000 can be achieved
through the use of iBTF at low resolution and scanning FPs beyond R ~2,000. The
third new technologies in BTFI is the use of EMCCDs for rapid and cyclically
wavelength scanning thus mitigating the damaging effect of atmospheric
variability through data acquisition. An additional important feature of the
instrument is that it has two optical channels which allow for the simultaneous
recording of the narrow-band, filtered image with the remaining (complementary)
broad-band light. This avoids the uncertainties inherent in tunable filter
imaging using a single detector. The system was designed to supply tunable
filter imaging with a field-of-view of 3 arcmin on a side, sampled at 0.12" for
direct Nasmyth seeing-limited area spectroscopy and for SAM's visitor
instrument port for GLAO-fed area spectroscopy. The instrument has seen first
light, as a SOAR visitor instrument. It is now in comissioning phase.Comment: accepted in PAS
Ultrafast wavelength jumping and wavelength adjustment with low current using monolithically integrated FML for long-reach UDWDM-PON
Ultrafast wavelength jumping at optical network units (ONUs) for an access network with frequency modulated lasers (FMLs) is demonstrated. This FML consists of an intracavity tunable phase section and filtering gain section. It provides a total of 4.2 nm tuning range with fast wavelength jumping (2.2 nm in 1 ”s) and fast adjustment (1.3 nm in 1.8 ns), providing a candidate for the fast tuning ONU for coherent ultradense wavelength-division multiplexing passive optical networks (WDM-PONs).Peer ReviewedPostprint (author's final draft
A Fully-Integrated Reconfigurable Dual-Band Transceiver for Short Range Wireless Communications in 180 nm CMOS
© 2015 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other users, including reprinting/ republishing this material for advertising or promotional purposes, creating new collective works for resale or redistribution to servers or lists, or reuse of any copyrighted components of this work in other works.A fully-integrated reconfigurable dual-band (760-960 MHz and 2.4-2.5 GHz) transceiver (TRX) for short range wireless communications is presented. The TRX consists of two individually-optimized RF front-ends for each band and one shared power-scalable analog baseband. The sub-GHz receiver has achieved the maximum 75 dBc 3rd-order harmonic rejection ratio (HRR3) by inserting a Q-enhanced notch filtering RF amplifier (RFA). In 2.4 GHz band, a single-ended-to-differential RFA with gain/phase imbalance compensation is proposed in the receiver. A ΣΠfractional-N PLL frequency synthesizer with two switchable Class-C VCOs is employed to provide the LOs. Moreover, the integrated multi-mode PAs achieve the output P1dB (OP1dB) of 16.3 dBm and 14.1 dBm with both 25% PAE for sub-GHz and 2.4 GHz bands, respectively. A power-control loop is proposed to detect the input signal PAPR in real-time and flexibly reconfigure the PA's operation modes to enhance the back-off efficiency. With this proposed technique, the PAE of the sub-GHz PA is improved by x3.24 and x1.41 at 9 dB and 3 dB back-off powers, respectively, and the PAE of the 2.4 GHz PA is improved by x2.17 at 6 dB back-off power. The presented transceiver has achieved comparable or even better performance in terms of noise figure, HRR, OP1dB and power efficiency compared with the state-of-the-art.Peer reviewe
Fast Switching Ferroelectric Materials for Accelerator Applications
Fast switching (< 10 nsec) measurement results on the recently developed
BST(M) (barium strontium titanium oxide composition with magnesium-based
additions) ferroelectric materials are presented. These materials can be used
as the basis for new advanced technology components suitable for high-gradient
accelerators. A ferroelectric ceramic has an electric field-dependent
dielectric permittivity that can be altered by applying a bias voltage.
Ferroelectric materials offer significant benefits for linear collider
applications, in particular, for switching and control elements where a very
short response time of <10 nsec is required. The measurement results presented
here show that the new BST(M) ceramic exhibits a high tunability factor: a bias
field of 40-50 kV/cm reduces the permittivity by a factor of 1.3-1.5. The
recently developed technology of gold biasing contact deposition on large
diameter (110 cm) thin wall ferroelectric rings allowed ~few nsec switching
times in witness sample experiments. The ferroelectric rings can be used at
high pulsed power (tens of megawatts) for X-band components as well as at high
average power in the range of a few kilowatts for the L-band phase-shifter,
under development for optimization of the ILC rf coupling. Accelerator
applications include fast active X-band and Ka-band high-power ferroelectric
switches, high-power X-band and L-band phase shifters, and tunable
dielectric-loaded accelerating structures.Comment: 7 pages, 6 figures, submitted to Proceedings of 2006 Advanced
Accelerator Concepts Worksho
Tunable 4-channel ultra-dense WDM demultiplexer with III-V photodiodes integrated in silicon-on-insulator
A tunable 4-channel ultra-dense WDM demultiplexer with 0.25nm channel spacing is demonstrated with III-V photodiodes integrated on Silicon-on-Insulator using rib waveguides. A possible application is an in-band label extractor for all-optical packet switching
Communication Subsystems for Emerging Wireless Technologies
The paper describes a multi-disciplinary design of modern communication systems. The design starts with the analysis of a system in order to define requirements on its individual components. The design exploits proper models of communication channels to adapt the systems to expected transmission conditions. Input filtering of signals both in the frequency domain and in the spatial domain is ensured by a properly designed antenna. Further signal processing (amplification and further filtering) is done by electronics circuits. Finally, signal processing techniques are applied to yield information about current properties of frequency spectrum and to distribute the transmission over free subcarrier channels
A Comparative Study Between a Micromechanical Cantilever Resonator and MEMS-based Passives for Band-pass Filtering Application
Over the past few years, significant growth has been observed in using MEMS
based passive components in the RF microelectronics domain, especially in
transceiver components. This is due to some excellent properties of the MEMS
devices like low loss, excellent isolation etc. in the microwave frequency
domain where the on-chip passives normally tend to become leakier and degrades
the transceiver performance. This paper presents a comparative analysis between
MEMS-resonator based and MEMS-passives based band-pass filter configurations
for RF applications, along with their design, simulation, fabrication and
characterization. The filters were designed to have a center frequency of 455
kHz, meant for use as the intermediate frequency (IF) filter in superheterodyne
receivers. The filter structures have been fabricated in PolyMUMPs process, a
three-polysilicon layer surface micromachining process.Comment: 6 pages, 15 figure
- âŠ