A survey of scan-capture power reduction techniques

With the advent of sub-nanometer geometries, integrated circuits (ICs) are required to be checked for newer defects. While scan-based architectures help detect these defects using newer fault models, test data inflation happens, increasing test time and test cost. An automatic test pattern generator (ATPG) exercise’s multiple fault sites simultaneously to reduce test data which causes elevated switching activity during the capture cycle. The switching activity results in an IR drop exceeding the devices under test (DUT) specification. An increase in IR-drop leads to failure of the patterns and may cause good DUTs to fail the test. The problem is severe during at-speed scan testing, which uses a functional rated clock with a high frequency for the capture operation. Researchers have proposed several techniques to reduce capture power. They used various methods, including the reduction of switching activity. This paper reviews the recently proposed techniques. The principle, algorithm, and architecture used in them are discussed, along with key advantages and limitations. In addition, it provides a classification of the techniques based on the method used and its application. The goal is to present a survey of the techniques and prepare a platform for future development in capture power reduction during scan testing

REDUCING POWER DURING MANUFACTURING TEST USING DIFFERENT ARCHITECTURES

Power during manufacturing test can be several times higher than power consumption in functional mode. Excessive power during test can cause IR drop, over-heating, and early aging of the chips. In this dissertation, three different architectures have been introduced to reduce test power in general cases as well as in certain scenarios, including field test. In the first architecture, scan chains are divided into several segments. Every segment needs a control bit to enable capture in a segment when new faults are detectable on that segment for that pattern. Otherwise, the segment should be disabled to reduce capture power. We group the control bits together into one or more control chains. To address the extra pin(s) required to shift data into the control chain(s) and significant post processing in the first architecture, we explored a second architecture. The second architecture stitches the control bits into the chains they control as EECBs (embedded enable capture bits) in between the segments. This allows an ATPG software tool to automatically generate the appropriate EECB values for each pattern to maintain the fault coverage. This also works in the presence of an on-chip decompressor. The last architecture focuses primarily on the self-test of a device in a 3D stacked IC when an existing FPGA in the stack can be programmed as a tester. We show that the energy expended during test is significantly less than would be required using low power patterns fed by an on-chip decompressor for the same very short scan chains

Impact of LFSR Seeding on the Test Pattern Generator in BIST

This paper considers the problem of minimizing the power required to test a BIST based combinational circuit without modifying the test pattern generator and with no extra area or delay overhead. The objective of this paper is to analyze the impact of the polynomial and seed selection of the LFSR on the power consumed by the circuit. It is shown that proper selection of the seed of the LFSR can lead to significant decrease in the power consumption of the BIST sessions. For this purpose, a Bit Flipping LFSR is used as a test pattern generator in the BIST design. Experimental results using the ISCAS benchmark circuits are reported, showing variations of the seed selected for the LFSR, the power consumed is ranging from 5.5% to 13.5%

A Modified Test Pattern Generation Architecture for Fault Detection in BIST

Multiple test patterns varying in a single bit position is generated for built-in-self-test (BIST). The test patterns generated using Johnson Counter and Seed Vector lacks in fault coverage. So Seed vector block is eliminated and patterns varying in single bit position is generated using 8 bit Johnson Counter has been proposed to have the required fault coverage with reduced test length. The generated test patterns have an advantage of minimum transition sequence. The methodology for producing the test vectors for BIST is coded using VHDL and simulations were performed with ModelSim 10.0b. The Area utilization and the power report were manipulated with the help of Xilinx ISE 9.1 software. The area reduction of 58% and power reduction of 9% is achieved while generating test patterns using Johnson counter

Algorithms for Power Aware Testing of Nanometer Digital ICs

At-speed testing of deep-submicron digital very large scale integrated (VLSI) circuits has become mandatory to catch small delay defects. Now, due to continuous shrinking of complementary metal oxide semiconductor (CMOS) transistor feature size, power density grows geometrically with technology scaling. Additionally, power dissipation inside a digital circuit during the testing phase (for test vectors under all fault models (Potluri, 2015)) is several times higher than its power dissipation during the normal functional phase of operation. Due to this, the currents that flow in the power grid during the testing phase, are much higher than what the power grid is designed for (the functional phase of operation). As a result, during at-speed testing, the supply grid experiences unacceptable supply IR-drop, ultimately leading to delay failures during at-speed testing. Since these failures are specific to testing and do not occur during functional phase of operation of the chip, these failures are usually referred to false failures, and they reduce the yield of the chip, which is undesirable. In nanometer regime, process parameter variations has become a major problem. Due to the variation in signalling delays caused by these variations, it is important to perform at-speed testing even for stuck faults, to reduce the test escapes (McCluskey and Tseng, 2000; Vorisek et al., 2004). In this context, the problem of excessive peak power dissipation causing false failures, that was addressed previously in the context of at-speed transition fault testing (Saxena et al., 2003; Devanathan et al., 2007a,b,c), also becomes prominent in the context of at-speed testing of stuck faults (Maxwell et al., 1996; McCluskey and Tseng, 2000; Vorisek et al., 2004; Prabhu and Abraham, 2012; Potluri, 2015; Potluri et al., 2015). It is well known that excessive supply IR-drop during at-speed testing can be kept under control by minimizing switching activity during testing (Saxena et al., 2003). There is a rich collection of techniques proposed in the past for reduction of peak switching activity during at-speed testing of transition/delay faults ii in both combinational and sequential circuits. As far as at-speed testing of stuck faults are concerned, while there were some techniques proposed in the past for combinational circuits (Girard et al., 1998; Dabholkar et al., 1998), there are no techniques concerning the same for sequential circuits. This thesis addresses this open problem. We propose algorithms for minimization of peak switching activity during at-speed testing of stuck faults in sequential digital circuits under the combinational state preservation scan (CSP-scan) architecture (Potluri, 2015; Potluri et al., 2015). First, we show that, under this CSP-scan architecture, when the test set is completely specified, the peak switching activity during testing can be minimized by solving the Bottleneck Traveling Salesman Problem (BTSP). This mapping of peak test switching activity minimization problem to BTSP is novel, and proposed for the first time in the literature. Usually, as circuit size increases, the percentage of don’t cares in the test set increases. As a result, test vector ordering for any arbitrary filling of don’t care bits is insufficient for producing effective reduction in switching activity during testing of large circuits. Since don’t cares dominate the test sets for larger circuits, don’t care filling plays a crucial role in reducing switching activity during testing. Taking this into consideration, we propose an algorithm, XStat, which is capable of performing test vector ordering while preserving don’t care bits in the test vectors, following which, the don’t cares are filled in an intelligent fashion for minimizing input switching activity, which effectively minimizes switching activity inside the circuit (Girard et al., 1998). Through empirical validation on benchmark circuits, we show that XStat minimizes peak switching activity significantly, during testing. Although XStat is a very powerful heuristic for minimizing peak input-switchingactivity, it will not guarantee optimality. To address this issue, we propose an algorithm that uses Dynamic Programming to calculate the lower bound for a given sequence of test vectors, and subsequently uses a greedy strategy for filling don’t cares in this sequence to achieve this lower bound, thereby guaranteeing optimality. This algorithm, which we refer to as DP-fill in this thesis, provides the globally optimal solution for minimizing peak input-switching-activity and also is the best known in the literature for minimizing peak input-switching-activity during testing. The proof of optimality of DP-fill in minimizing peak input-switching-activity is also provided in this thesis

The 30/20 GHz flight experiment system, phase 2. Volume 2: Experiment system description

A detailed technical description of the 30/20 GHz flight experiment system is presented. The overall communication system is described with performance analyses, communication operations, and experiment plans. Hardware descriptions of the payload are given with the tradeoff studies that led to the final design. The spacecraft bus which carries the payload is discussed and its interface with the launch vehicle system is described. Finally, the hardwares and the operations of the terrestrial segment are presented