Novel algorithms for fair bandwidth sharing on counter rotating rings

Rings are often preferred technology for networks as ring networks can virtually create fully connected mesh networks efficiently and they are also easy to manage. However, providing fair service to all the stations on the ring is not always easy to achieve. In order to capitalize on the advantages of ring networks, new buffer insertion techniques, such as Spatial Reuse Protocol (SRP), were introduced in early 2000s. As a result, a new standard known as IEEE 802.17 Resilient Packet Ring was defined in 2004 by the IEEE Resilient Packet Ring (RPR) Working Group. Since then two addenda have been introduced; namely, IEEE 802.17a and IEEE 802.17b in 2006 and 2010, respectively. During this standardization process, weighted fairness and queue management schemes were proposed to be used in the standard. As shown in this dissertation, these schemes can be applied to solve the fairness issues noted widely in the research community as radical changes are not practical to introduce within the context of a standard. In this dissertation, the weighted fairness aspects of IEEE 802.17 RPR (in the aggressive mode of operation) are studied; various properties are demonstrated and observed via network simulations, and additional improvements are suggested. These aspects have not been well studied until now, and can be used to alleviate some of the issues observed in the fairness algorithm under some scenarios. Also, this dissertation focuses on the RPR Medium Access Control (MAC) Client implementation of the IEEE 802.17 RPR MAC in the aggressive mode of operation and introduces a new active queue management scheme for ring networks that achieves higher overall utilization of the ring bandwidth with simpler and less expensive implementation than the generic implementation provided in the standard. The two schemes introduced in this dissertation provide performance comparable to the per destination queuing implementation, which yields the best achievable performance at the expense of the cost of implementation. In addition, till now the requirements for sizing secondary transit queue of IEEE 802.17 RPR stations (in the aggressive mode of operation) have not been properly investigated. The analysis and suggested improvements presented in this dissertation are then supported by performance evaluation results and theoretical calculations. Last, but not least, the impact of using different capacity links on the same ring has not been investigated before from the ring utilization and fairness points of view. This dissertation also investigates utilizing different capacity links in RPR and proposes a mechanism to support the same

Efficient and Effective Schemes for Streaming Media Delivery

The rapid expansion of the Internet and the increasingly wide deployment of wireless networks provide opportunities to deliver streaming media content to users at anywhere, anytime. To ensure good user experience, it is important to battle adversary effects, such as delay, loss and jitter. In this thesis, we first study efficient loss recovery schemes, which require pure XOR operations. In particular, we propose a novel scheme capable of recovering up to 3 packet losses, and it has the lowest complexity among all known schemes. We also propose an efficient algorithm for array codes decoding, which achieves significant throughput gain and energy savings over conventional codes. We believe these schemes are applicable to streaming applications, especially in wireless environments. We then study quality adaptation schemes for client buffer management. Our control-theoretic approach results in an efficient online rate control algorithm with analytically tractable performance. Extensive experimental results show that three goals are achieved: fast startup, continuous playback in the face of severe congestion, and maximal quality and smoothness over the entire streaming session. The scheme is later extended to streaming with limited quality levels, which is then directly applicable to existing systems

A study of the applicability of software-defined networking in industrial networks

173 p.Las redes industriales interconectan sensores y actuadores para llevar a cabo funciones de monitorización, control y protección en diferentes entornos, tales como sistemas de transporte o sistemas de automatización industrial. Estos sistemas ciberfísicos generalmente están soportados por múltiples redes de datos, ya sean cableadas o inalámbricas, a las cuales demandan nuevas prestaciones, de forma que el control y gestión de tales redes deben estar acoplados a las condiciones del propio sistema industrial. De este modo, aparecen requisitos relacionados con la flexibilidad, mantenibilidad y adaptabilidad, al mismo tiempo que las restricciones de calidad de servicio no se vean afectadas. Sin embargo, las estrategias de control de red tradicionales generalmente no se adaptan eficientemente a entornos cada vez más dinámicos y heterogéneos.Tras definir un conjunto de requerimientos de red y analizar las limitaciones de las soluciones actuales, se deduce que un control provisto independientemente de los propios dispositivos de red añadiría flexibilidad a dichas redes. Por consiguiente, la presente tesis explora la aplicabilidad de las redes definidas por software (Software-Defined Networking, SDN) en sistemas de automatización industrial. Para llevar a cabo este enfoque, se ha tomado como caso de estudio las redes de automatización basadas en el estándar IEC 61850, el cual es ampliamente usado en el diseño de las redes de comunicaciones en sistemas de distribución de energía, tales como las subestaciones eléctricas. El estándar IEC 61850 define diferentes servicios y protocolos con altos requisitos en terminos de latencia y disponibilidad de la red, los cuales han de ser satisfechos mediante técnicas de ingeniería de tráfico. Como resultado, aprovechando la flexibilidad y programabilidad ofrecidas por las redes definidas por software, en esta tesis se propone una arquitectura de control basada en el protocolo OpenFlow que, incluyendo tecnologías de gestión y monitorización de red, permite establecer políticas de tráfico acorde a su prioridad y al estado de la red.Además, las subestaciones eléctricas son un ejemplo representativo de infraestructura crítica, que son aquellas en las que un fallo puede resultar en graves pérdidas económicas, daños físicos y materiales. De esta forma, tales sistemas deben ser extremadamente seguros y robustos, por lo que es conveniente la implementación de topologías redundantes que ofrezcan un tiempo de reacción ante fallos mínimo. Con tal objetivo, el estándar IEC 62439-3 define los protocolos Parallel Redundancy Protocol (PRP) y High-availability Seamless Redundancy (HSR), los cuales garantizan un tiempo de recuperación nulo en caso de fallo mediante la redundancia activa de datos en redes Ethernet. Sin embargo, la gestión de redes basadas en PRP y HSR es estática e inflexible, lo que, añadido a la reducción de ancho de banda debida la duplicación de datos, hace difícil un control eficiente de los recursos disponibles. En dicho sentido, esta tesis propone control de la redundancia basado en el paradigma SDN para un aprovechamiento eficiente de topologías malladas, al mismo tiempo que se garantiza la disponibilidad de las aplicaciones de control y monitorización. En particular, se discute cómo el protocolo OpenFlow permite a un controlador externo configurar múltiples caminos redundantes entre dispositivos con varias interfaces de red, así como en entornos inalámbricos. De esta forma, los servicios críticos pueden protegerse en situaciones de interferencia y movilidad.La evaluación de la idoneidad de las soluciones propuestas ha sido llevada a cabo, principalmente, mediante la emulación de diferentes topologías y tipos de tráfico. Igualmente, se ha estudiado analítica y experimentalmente cómo afecta a la latencia el poder reducir el número de saltos en las comunicaciones con respecto al uso de un árbol de expansión, así como balancear la carga en una red de nivel 2. Además, se ha realizado un análisis de la mejora de la eficiencia en el uso de los recursos de red y la robustez alcanzada con la combinación de los protocolos PRP y HSR con un control llevado a cabo mediante OpenFlow. Estos resultados muestran que el modelo SDN podría mejorar significativamente las prestaciones de una red industrial de misión crítica

Fairness in a data center

Existing data centers utilize several networking technologies in order to handle the performance requirements of different workloads. Maintaining diverse networking technologies increases complexity and is not cost effective. This results in the current trend to converge all traffic into a single networking fabric. Ethernet is both cost-effective and ubiquitous, and as such it has been chosen as the technology of choice for the converged fabric. However, traditional Ethernet does not satisfy the needs of all traffic workloads, for the most part, due to its lossy nature and, therefore, has to be enhanced to allow for full convergence. The resulting technology, Data Center Bridging (DCB), is a new set of standards defined by the IEEE to make Ethernet lossless even in the presence of congestion. As with any new networking technology, it is critical to analyze how the different protocols within DCB interact with each other as well as how each protocol interacts with existing technologies in other layers of the protocol stack. This dissertation presents two novel schemes that address critical issues in DCB networks: fairness with respect to packet lengths and fairness with respect to flow control and bandwidth utilization. The Deficit Round Robin with Adaptive Weight Control (DRR-AWC) algorithm actively monitors the incoming streams and adjusts the scheduling weights of the outbound port. The algorithm was implemented on a real DCB switch and shown to increase fairness for traffic consisting of mixed-length packets. Targeted Priority-based Flow Control (TPFC) provides a hop-by-hop flow control mechanism that restricts the flow of aggressor streams while allowing victim streams to continue unimpeded. Two variants of the targeting mechanism within TPFC are presented and their performance evaluated through simulation

Investigation of methods for data communication and power delivery through metals

PhD ThesisThe retrieval of data from a sensor, enclosed by a metallic structure, such as a naval vessel, pipeline or nuclear flask is often very challenging. To maintain structural integrity it is not desirable to penetrate the wall of the structure, preventing any hard-wired solution. Furthermore, the conductive nature of the structure prevents the use of radio communications. Applications involving sealed containers also have a requirement for power delivery, as the periodic changing of batteries is not possible. Ultrasound has previously been identified as an attractive approach but there are two key challenges: efficient/reliable ultrasonic transduction and a method of overcoming the inherent multipath distortion resulting from boundary reflections. Previous studies have utilised piezoelectric contact transducers, however, they are impractical due to their reliance on coupling, i.e. the bond between the transducer and the metal surface, which leads to concerns over long term reliability. A non-contact transducer overcomes this key drawback, thus highlighting the electromagnetic acoustic transducer (EMAT) as a favourable alternative. This thesis presents the design and testing of an EMAT with appropriate characteristics for through-metal data communications. A low cost, low power data transmission scheme is presented for overcoming acoustic multipath based on pulse position modulation (PPM). Due to the necessary guard time, the data rate is limited to 50kbps. A second solution is presented employing continuous wave, Quadrature phase shift keying (QPSK) modulation, allowing data rates in excess of 1Mbps to be achieved. Equalisation is required to avoid intersymbol interference (ISI) and a decision feedback equaliser (DFE) is shown to be adept at mitigating this effect. The relatively low efficiency of an EMAT makes it unsuitable for power delivery, consequently, an alternative non-contact approach, utilising inductive coupling, is explored. Power transfer efficiency of ≈ 4% is shown to be achievable through 20mm thick stainless steel.ICS department of BAE Systems Submarine Solutions, EPSR