The Level-0 Muon Trigger for the LHCb Experiment

A very compact architecture has been developed for the first level Muon Trigger of the LHCb experiment that processes 40 millions of proton-proton collisions per second. For each collision, it receives 3.2 kBytes of data and it finds straight tracks within a 1.2 microseconds latency. The trigger implementation is massively parallel, pipelined and fully synchronous with the LHC clock. It relies on 248 high density Field Programable Gate arrays and on the massive use of multigigabit serial link transceivers embedded inside FPGAs.Comment: 33 pages, 16 figures, submitted to NIM

Pcie Ip Validation Process Across Process Corner, Voltage And Temperature Conditions

IP validation has become more challenging for FPGA device as it supports high operating speed. The Peripheral Component Interconnect Express (PCIe) is an IP used for high speed data transfer that supported by Intel FPGAs. The base specifications of PCIe 3.0 supports 8.0 GT/s, 5.0 GT/s and 2.5 GT/s. The link training and Initialization takes place at physical layer to initialize the link width and link data rate. The physical layer is getting more complex when it supports higher speed. The operational state only happens when Link Training and Status State Machine (LTSSM) reaches L0 state after device being configured. The stability of link training is improved by optimizing the soft logic design in application layer. Two protocol tests usually validated in industry are link up testing and link & higher layer testing. Debugging tools supported by Quartus are fully utilized to detect any failure during link training. The characterization of link performance covers process corners, voltage and temperature conditions are hard to analyze. By using hypothesis testing method, data collected gives a clear trend on the PCIe link performance. The H0 statement shows a significant difference for passing and failing case. In this research, the worst case happened at low voltage and low temperature regardless of any process corners. The p-value is greater than 0.05 proved H0 statement is accepted. The difference on passing and failing percentage is insignificantly impacting overall link performance of PCIe. It concludes that the bug is random and not caused by any defects on the silicon layout of FPGA device. Thus, IP validation shows the robustness of the device and able to comply with base specification of PCIe

Experimental Evaluation and Comparison of Time-Multiplexed Multi-FPGA Routing Architectures

Emulating large complex designs require multi-FPGA systems (MFS). However, inter-FPGA communication is confronted by the challenge of lack of interconnect capacity due to limited number of FPGA input/output (I/O) pins. Serializing parallel signals onto a single trace effectively addresses the limited I/O pin obstacle. Besides the multiplexing scheme and multiplexing ratio (number of inter-FPGA signals per trace), the choice of the MFS routing architecture also affect the critical path latency. The routing architecture of an MFS is the interconnection pattern of FPGAs, fixed wires and/or programmable interconnect chips. Performance of existing MFS routing architectures is also limited by off-chip interface selection. In this dissertation we proposed novel 2D and 3D latency-optimized time-multiplexed MFS routing architectures. We used rigorous experimental approach and real sequential benchmark circuits to evaluate and compare the proposed and existing MFS routing architectures. This research provides a new insight into the encouraging effects of using off-chip optical interface and three dimensional MFS routing architectures. The vertical stacking results in shorter off-chip links improving the overall system frequency with the additional advantage of smaller footprint area. The proposed 3D architectures employed serialized interconnect between intra-plane and inter-plane FPGAs to address the pin limitation problem. Additionally, all off-chip links are replaced by optical fibers that exhibited latency improvement and resulted in faster MFS. Results indicated that exploiting third dimension provided latency and area improvements as compared to 2D MFS. We also proposed latency-optimized planar 2D MFS architectures in which electrical interconnections are replaced by optical interface in same spatial distribution. Performance evaluation and comparison showed that the proposed architectures have reduced critical path delay and system frequency improvement as compared to conventional MFS. We also experimentally evaluated and compared the system performance of three inter-FPGA communication schemes i.e. Logic Multiplexing, SERDES and MGT in conjunction with two routing architectures i.e. Completely Connected Graph (CCG) and TORUS. Experimental results showed that SERDES attained maximum frequency than the other two schemes. However, for very high multiplexing ratios, the performance of SERDES & MGT became comparable

A Fully Bidirectional Optical Network With Latency Monitoring Capability for the Distribution of Timing-Trigger and Control Signals in High-Energy Physics Experiments

The present paper discusses recent advances on a Passive Optical Network inspired Timing-Trigger and Control scheme for the future upgrade of the TTC system installed in the LHC experiments' and more specifically the currently known as TTCex to TTCrx link. The timing PON is implemented with commercially available FPGAs and 1-Gigabit Ethernet PON transceivers and provides a fixed latency gigabit downlink that can carry level-1 trigger accept decisions and commands as well as an upstream link for feedback from the front-end electronics

Development of electronics for the VELO upgrade detector

Esta tesis cubre el diseño electrónico del detector de vértices (VELO) del experimento LHCb del CERN. El VELO está situado rodeando el punto de colisión de los dos haces de protones del LHC del CERN. Su diseño está lleno de restricciones que requieren diseños novedosos: minimizar la materia cerca del punto de colisión, diseño de componentes que soporten radiación, transmisión de datos a alta tasa y el procesado de los mismos, sincronización del sistema, etc. El trabajo presentado en esta tesis se centra en: por un lado, la validación del hardware y sus diferentes prototipos, por otro lado, el diseño del firmware de las FPGAs encargadas del control, sincronización y adquisición de datos del VELO

Sistemas de calibração automático para transceivers NG-PON2

The current society is increasingly dependent on communication services, requiring better and faster connections, predicting in a near future connections in the order of hundreds of Gbit/s. During the data transmissions, the increase of speed reflects an increase of the error ratio due to factors such as noise, reductions of signal or jitter, which for low speed these were not emphasized so much. This project involves the development of a BER test system for both continuous and Burst mode of the transmission, demonstrating the viability of communication over the next-generation technology, NG-PON2, which uses high transmission rates (10 Gbit/s). For this purpose, an FPGA architecture was implemented that allows for long distances in the optical network, high transmission rates. This choice reflects a more economical alternative in relation to commercial equipment and has several advantages, such as the flexibility to reprogram and prepare the architecture according to the needs of the user. To achieve the proposed requirements, the project was divided into three parts. In the first part an architecture was developed that allows to obtain the error rate during a continuous mode transmission. In order to obtain the real-time viability of the communication referred and to have control over the system, an interface was developed between the computer and the FPGA to change certain characteristics of the communication channel. This is the second part of the project. The last part of the project has an architecture similar to the previous one, that is, instead of the transmission to be done in continuous mode, it is performed in mode Burst, being this the requirement with more interest to the technology NG-PON2. Finally, proof of concept was performed through an optical network provided by the company PICadvanced that allowed the validation of the different parts of the project. These validations will allow the development of new modules that will later contribute to the main project that is under development in the company PICadvanced, which aims at the construction of an automatic calibration board for the XFP transceivers.A sociedade atual depende cada vez mais dos serviços de comunicação, exigindo melhores ligações e mais rápidas, prevendo-se num futuro próximo a necessidade de ligações na ordem das centenas de Gbit/s. O aumento dos ritmos de transmissão refletem um aumento no que se refere à taxa de erro (BER), uma vez que o impacto associado a fatores como ruı́do ou interferência entre sı́mbolos, é maior do que para baixos ritmos. Este trabalho foca-se no desenvolvimento de um sistema de teste BER, tanto para uma transmissão contı́nua como para transmissão em rajadas, que demonstre a viabilidade da comunicação sobre a tecnologia da próxima geração, Next Generation Passive Optical Network 2 (NG-PON2), que utiliza débitos de transmissão elevados (10 Gbit/s). Para este efeito foi implementado uma arquitetura em Field-programmable gate array (FPGA) que possibilita para longas distâncias na rede ótica, elevados ritmos de transmissão. Esta escolha reflete uma alterativa mais económica em relação aos equipamentos comerciais e apresenta vantagens tais como a flexibilidade de reprogramar e preparar a arquitetura de acordo com as necessidades do utilizador. Para cumprir os requisitos propostos o projeto dividiu-se em três partes. Numa primeira parte do projeto desenvolveu-se uma arquitetura que permite adquirir a taxa de erros durante uma transmissão contı́nua. Com o intuito de analisar a viabilidade em tempo real da comunicação em questão, bem com o utilizador ter controlo sobre o sistema, alterando certas caracterı́sticas do canal de comunicação, desenvolveu-se numa segunda parte do projeto uma interface entre o computador e a FPGA. Numa última parte do projeto desenvolveu-se uma arquitetura semelhante à anterior, na qual se permite igualmente adquirir a taxa de erros com transmissão em rajadas (Burst), sendo este um dos requisitos de maior interesse na tecnologia NG-PON2. Por fim, a prova de conceito foi realizada através de uma rede ótica disponibilizada pela empresa PICadvanced, que permitiu a validação das diversas partes do projeto. Estas validações vão permitir a conceção de novos módulos que posteriormente vão contribuir para o projeto fonte que está em desenvolvimento na empresa PICadvanced, que visa a implementação de uma placa de calibração automatizada para os transceptores 10 Gigabit Small Form Factor Pluggables (XFP).Mestrado em Engenharia Eletrónica e Telecomunicaçõe

Implementing Pulse Compression in the Iwrap Airborne Doppler Radar/Scatterometer

The pulse compression scheme implemented on the Imaging Wind and Rain Air-borne Profiler (IWRAP) is described. Developed at the UMASS Microwave Remote Sensing Laboratory (MIRSL), IWRAP is a dual-band (C and Ku) conically scanning Doppler scatterometer designed to map the atmospheric boundary layer wind fields, ocean surface wind fields, and precipitation within tropical cyclones. IWRAP has previously been deployed using a pulsed transmit waveform with a peak transmit power of 80 watts. This limits the average transmit power and sensitivity for the system which affects the more distant range gates (especially at Ku-band). As a result, IWRAP could operate only at lower altitudes (approx. 5000 ft) causing safety concerns and limiting the missions for which it can be deployed. Increasing sensitivity was achieved by converting IWRAP to a pulse compression radar system. Pulse compression is a technique that combines the increased energy of a longer pulse with the high resolution of a short pulse by implementing a frequency modulated (FM) “chirped” transmit waveform. This method requires advanced signal processing, in which the received signal is passed through a filter to compress the pulse on the receiving end. A system with various chirp/filtering schemes as well as a new control system which UMASS has recently developed will be discussed in this thesis

Extension of the L1Calo PreProcessor System for the ATLAS Phase-I Calorimeter Trigger Upgrade

For the Run-3 data-taking period at the Large Hadron Collider (LHC), the hardware- based Level-1 Calorimeter Trigger (L1Calo) of the ATLAS experiment was upgraded. Through new and sophisticated algorithms, the upgrade will increase the trigger performance in a challenging, high-pileup environment while maintaining low selection thresholds. The Tile Rear Extension (TREX) modules are the latest addition to the L1Calo PreProcessor system. Hosting state-of-the-art FPGAs and high-speed optical transceivers, the TREX modules provide digitised hadronic transverse energies from the ATLAS Tile Calorimeter to the new feature extractor (FEX) processors every 25 ns. In addition, the modules are designed to maintain compatibility with the original trigger processors. The system of 32 TREX modules has been developed, produced and successfully installed in ATLAS. The thesis describes the functional implementation of the modules and the detailed integration and commissioning into the ATLAS detector