A radiation-hard dual-channel 12-bit 40 MS/s ADC prototype for the ATLAS liquid argon calorimeter readout electronics upgrade at the CERN LHC

The readout electronics upgrade for the ATLAS Liquid Argon Calorimeters at the CERN Large Hadron Collider requires a radiation-hard ADC. The design of a radiation-hard dual-channel 12-bit 40 MS/s pipeline ADC for this use is presented. The design consists of two pipeline A/D channels each with four Multiplying Digital-to-Analog Converters followed by 8-bit Successive-Approximation-Register analog-to-digital converters. The custom design, fabricated in a commercial 130 nm CMOS process, shows a performance of 67.9 dB SNDR at 10 MHz for a single channel at 40 MS/s, with a latency of 87.5 ns (to first bit read out), while its total power consumption is 50 mW/channel. The chip uses two power supply voltages: 1.2 and 2.5 V. The sensitivity to single event effects during irradiation is measured and determined to meet the system requirements

Low-Power Slew-Rate Boosting Based 12-Bit Pipeline ADC Utilizing Forecasting Technique in the Sub-ADCS

The dissertation presents architecture and circuit solutions to improve the power efficiency of high-speed 12-bit pipelined ADCs in advanced CMOS technologies. First, the 4.5bit algorithmic pipelined front-end stage is proposed. It is shown that the algorithmic pipelined ADC requires a simpler sub-ADC and shows lower sensitivity to the Multiplying DAC (MDAC) errors and smaller area and power dissipation in comparison to the conventional multi-bit per stage pipelined ADC. Also, it is shown that the algorithmic pipelined architecture is more tolerant to capacitive mismatch for the same input-referred thermal noise than the conventional multi-bit per stage architecture. To take full advantage of these properties, a modified residue curve for the pipelined ADC is proposed. This concept introduces better linearity compared with the conventional residue curve of the pipelined ADC; this approach is particularly attractive for the digitization of signals with large peak to average ratio such as OFDM coded signals. Moreover, the minimum total required transconductance for the different architectures of the 12-bit pipelined ADC are computed. This helps the pipelined ADC designers to find the most power-efficient architecture between different topologies based on the same input-referred thermal noise. By employing this calculation, the most power efficient architecture for realizing the 12-bit pipelined ADC is selected. Then, a technique for slew-rate (SR) boosting in switched-capacitor circuits is proposed in the order to be utilized in the proposed 12-bit pipelined ADC. This technique makes use of a class-B auxiliary amplifier that generates a compensating current only when high slew-rate is demanded by large input signal. The proposed architecture employs simple circuitry to detect the need of injecting current at the output load by implementing a Pre-Amp followed by a class-B amplifier, embedded with a pre-defined hysteresis, in parallel with the main amplifier to boost its slew phase. The proposed solution requires small static power since it does not need high dc-current at the output stage of the main amplifier. The proposed technique is suitable for high-speed low-power multi-bit/stage pipelined ADC applications. Both transistor-level simulations and experimental results in TSMC 40nm technology reduces the slew-time for more than 45% and shorts the 1% settling time by 28% when used in a 4.5bit/stage pipelined ADC; power consumption increases by 20%. In addition, the technique of inactivating and disconnecting of the sub-ADC’s comparators by forecasting the sign of the sampled input voltage is proposed in the order to reduce the dynamic power consumption of the sub-ADCs in the proposed 12-bit pipelined ADC. This technique reduces the total dynamic power consumption more than 46%. The implemented 12-bit pipelined ADC achieves an SNDR/SFDR of 65.9/82.3 dB at low input frequencies and a 64.1/75.5 dB near Nyquist frequency while running at 500 MS/s. The pipelined ADC prototype occupies an active area of 0.9 mm^2 and consumes 18.16 mW from a 1.1 V supply, resulting in a figure of merit (FOM) of 22.4 and a 27.7 fJ/conversion-step at low-frequency and Nyquist frequency, respectively

Low-Power Slew-Rate Boosting Based 12-Bit Pipeline ADC Utilizing Forecasting Technique in the Sub-ADCS

The dissertation presents architecture and circuit solutions to improve the power efficiency of high-speed 12-bit pipelined ADCs in advanced CMOS technologies. First, the 4.5bit algorithmic pipelined front-end stage is proposed. It is shown that the algorithmic pipelined ADC requires a simpler sub-ADC and shows lower sensitivity to the Multiplying DAC (MDAC) errors and smaller area and power dissipation in comparison to the conventional multi-bit per stage pipelined ADC. Also, it is shown that the algorithmic pipelined architecture is more tolerant to capacitive mismatch for the same input-referred thermal noise than the conventional multi-bit per stage architecture. To take full advantage of these properties, a modified residue curve for the pipelined ADC is proposed. This concept introduces better linearity compared with the conventional residue curve of the pipelined ADC; this approach is particularly attractive for the digitization of signals with large peak to average ratio such as OFDM coded signals. Moreover, the minimum total required transconductance for the different architectures of the 12-bit pipelined ADC are computed. This helps the pipelined ADC designers to find the most power-efficient architecture between different topologies based on the same input-referred thermal noise. By employing this calculation, the most power efficient architecture for realizing the 12-bit pipelined ADC is selected. Then, a technique for slew-rate (SR) boosting in switched-capacitor circuits is proposed in the order to be utilized in the proposed 12-bit pipelined ADC. This technique makes use of a class-B auxiliary amplifier that generates a compensating current only when high slew-rate is demanded by large input signal. The proposed architecture employs simple circuitry to detect the need of injecting current at the output load by implementing a Pre-Amp followed by a class-B amplifier, embedded with a pre-defined hysteresis, in parallel with the main amplifier to boost its slew phase. The proposed solution requires small static power since it does not need high dc-current at the output stage of the main amplifier. The proposed technique is suitable for high-speed low-power multi-bit/stage pipelined ADC applications. Both transistor-level simulations and experimental results in TSMC 40nm technology reduces the slew-time for more than 45% and shorts the 1% settling time by 28% when used in a 4.5bit/stage pipelined ADC; power consumption increases by 20%. In addition, the technique of inactivating and disconnecting of the sub-ADC’s comparators by forecasting the sign of the sampled input voltage is proposed in the order to reduce the dynamic power consumption of the sub-ADCs in the proposed 12-bit pipelined ADC. This technique reduces the total dynamic power consumption more than 46%. The implemented 12-bit pipelined ADC achieves an SNDR/SFDR of 65.9/82.3 dB at low input frequencies and a 64.1/75.5 dB near Nyquist frequency while running at 500 MS/s. The pipelined ADC prototype occupies an active area of 0.9 mm^2 and consumes 18.16 mW from a 1.1 V supply, resulting in a figure of merit (FOM) of 22.4 and a 27.7 fJ/conversion-step at low-frequency and Nyquist frequency, respectively

Offset-calibration with Time-Domain Comparators Using Inversion-mode Varactors

This paper presents a differential time-domain comparator formed by two voltage controlled delay lines, one per input terminal, and a binary phase detector for comparison solving. The propagation delay through the respective lines can be adjusted with a set of digitally-controlled inversion-mode varactors. These varactors provide tuning capabilities to the comparator; feature which can be exploited for offset calibration. This is demonstrated with the implementation of a differential 10-bit SAR-ADC. The design, fabricated in a 0.18μm CMOS process, includes an automatic mechanism for adjusting the capacitance of the varactors in order to calibrate the offset of the whole converter. Correct functionality was measured in all samples.Ministerio de Economía y Competitividad TEC2016-80923-POffice of Naval Research (USA) N0001414135

A Low-Power, Reconfigurable, Pipelined ADC with Automatic Adaptation for Implantable Bioimpedance Applications

Biomedical monitoring systems that observe various physiological parameters or electrochemical reactions typically cannot expect signals with fixed amplitude or frequency as signal properties can vary greatly even among similar biosignals. Furthermore, advancements in biomedical research have resulted in more elaborate biosignal monitoring schemes which allow the continuous acquisition of important patient information. Conventional ADCs with a fixed resolution and sampling rate are not able to adapt to signals with a wide range of variation. As a result, reconfigurable analog-to-digital converters (ADC) have become increasingly more attractive for implantable biosensor systems. These converters are able to change their operable resolution, sampling rate, or both in order convert changing signals with increased power efficiency. Traditionally, biomedical sensing applications were limited to low frequencies. Therefore, much of the research on ADCs for biomedical applications focused on minimizing power consumption with smaller bias currents resulting in low sampling rates. However, recently bioimpedance monitoring has become more popular because of its healthcare possibilities. Bioimpedance monitoring involves injecting an AC current into a biosample and measuring the corresponding voltage drop. The frequency of the injected current greatly affects the amplitude and phase of the voltage drop as biological tissue is comprised of resistive and capacitive elements. For this reason, a full spectrum of measurements from 100 Hz to 10-100 MHz is required to gain a full understanding of the impedance. For this type of implantable biomedical application, the typical low power, low sampling rate analog-to-digital converter is insufficient. A different optimization of power and performance must be achieved. Since SAR ADC power consumption scales heavily with sampling rate, the converters that sample fast enough to be attractive for bioimpedance monitoring do not have a figure-of-merit that is comparable to the slower converters. Therefore, an auto-adapting, reconfigurable pipelined analog-to-digital converter is proposed. The converter can operate with either 8 or 10 bits of resolution and with a sampling rate of 0.1 or 20 MS/s. Additionally, the resolution and sampling rate are automatically determined by the converter itself based on the input signal. This way, power efficiency is increased for input signals of varying frequency and amplitude

Design Techniques for High-Performance SAR A/D Converters

The design of electronics needs to account for the non-ideal characteristics of the device technologies used to realize practical circuits. This is particularly important in mixed analog-digital design since the best device technologies are very different for digital compared to analog circuits. One solution for this problem is to use a calibration correction approach to remove the errors introduced by devices, but this adds complexity and power dissipation, as well as reducing operation speed, and so must be optimised. This thesis addresses such an approach to improve the performance of certain types of analog-to-digital converter (ADC) used in advanced telecommunications, where speed, accuracy and power dissipation currently limit applications. The thesis specifically focuses on the design of compensation circuits for use in successive approximation register (SAR) ADCs. ADCs are crucial building blocks in communication systems, in general, and for mobile networks, in particular. The recently launched fifth generation of mobile networks (5G) has required new ADC circuit techniques to meet the higher speed and lower power dissipation requirements for 5G technology. The SAR has become one of the most favoured architectures for designing high-performance ADCs, but the successive nature of the circuit operation makes it difficult to reach ∼GS/s sampling rates at reasonable power consumption. Here, two calibration techniques for high-performance SAR ADCs are presented. The first uses an on-chip stochastic-based mismatch calibration technique that is able to accurately compute and compensate for the mismatch of a capacitive DAC in a SAR ADC. The stochastic nature of the proposed calibration method enables determination of the mismatch of the CAPDAC with a resolution much better than that of the DAC. This allows the unit capacitor to scale down to as low as 280aF for a 9-bit DAC. Since the CAP-DAC causes a large part of the overall dynamic power consumption and directly determines both the sizes of the driving and sampling switches and the size of the input capacitive load of the ADC and the kT/C noise power, a small CAP-DAC helps the power efficiency. To validate the proposed calibration idea, a 10-bit asynchronous SAR ADC was fabricated in 28-nm CMOS. Measurement results show that the proposed stochastic calibration improves the ADC’s SFDR and SNDR by 14.9 dB, 11.5 dB, respectively. After calibration, the fabricated SAR ADC achieves an ENOB of 9.14 bit at a sampling rate of 85 MS/s, resulting in a Walden FoM of 10.9 fJ/c-s. The second calibration technique is a timing-skew calibration for a time-interleaved (TI) SAR ADC that calibrates/computes the inter-channel timing and offset mismatch simultaneously. Simulation results show the effectiveness of this calibration method. When used together, the proposed mismatch calibration technique and the timing-skew calibration technique enables a TI SAR ADC to be designed that can achieve a sampling rate of ∼GS/s with 10-bit resolution and a power consumption as low as ∼10mW; specifications that satisfy the requirements of 5G technology

Design techniques for low-power SAR ADCs in nano-scale CMOS technologies

This thesis presents low power design techniques for successive approximation register (SAR) analog-to-digital converters (ADCs) in nano-scale CMOS technologies. Low power SAR ADCs face two major challenges especially at high resolutions: (1) increased comparator power to suppress the noise, and (2) increased DAC switching energy due to the large DAC size. To improve the comparator’s power efficiency, a statistical estimation based comparator noise reduction technique is presented. It allows a low power and noisy comparator to achieve high signal-to-noise ratio (SNR) by estimating the conversion residue. A first prototype ADC in 65nm CMOS has been developed to validate the proposed noise reduction technique. It achieves 4.5 fJ/conv-step Walden figure of merit and 64.5 dB signal-to-noise and distortion ratio (SNDR). In addition, a bidirectional single-side switching technique is developed to reduce the DAC switching power. It can reduce the DAC switching power and the total number of unit capacitors by 86% and 75%, respectively. A second prototype ADC with the proposed switching technique is designed and fabricated in 180nm CMOS technology. It achieves an SNDR of 63.4 dB and consumes only 24 Wat 1MS/s, leading to aWalden figure of merit of 19.9 fJ/conv-step. This thesis also presents an improved loop-unrolled SAR ADC, which works at high frequency with reduced SAR logic power and delay. It employs the bidirectional single-side switching technique to reduce the comparator common-mode voltage variation. In addition, it uses a Vcm-adaptive offset calibration technique which can accurately calibrate comparator’s offset at its operating Vcm. A prototype ADC designed in 40nm CMOS achieves 35 dB at 700 MS/s sampling rate and consumes only 0.95 mW, leading to a Walden figure of merit of 30 fJ/conv-step.Electrical and Computer Engineerin

Energy-efficient data converter design in scaled CMOS technology

Data converters bridge the physical and digital worlds. They have been the crucial building blocks in modern electronic systems, and are expected to have a growing significance in the booming era of Internet-of-Things (IoT) and 5G communications. The applications raise energy-efficiency requirements for both low-speed and high-speed converters since they are widely deployed in wireless sensor nodes and portable devices. To explore the solutions, the author worked on three directions: 1) techniques to improve the efficiency of the low-speed converters including the comparator; 2) techniques to develop high-speed data converters including the reference stabilization; 3) new architecture to improve the efficiency of the capacitance-to-digital converter (CDC). In the first part, a power-efficient 10-bit SAR ADC featured with a gain-boosted dynamic comparator is presented. In energy-constrained applications, the converter is usually supplied with low supply voltage (e.g., 0.3 V-0.5 V), which reduces the comparator pre-amplifier (pre-amp) gain and results in higher noise. A novel comparator topology with a dynamic common-gate stage is proposed to increase the pre-amplification gain, thereby reducing noise and offset. Besides, statistical estimation and loading switching techniques are combined to further improve energy efficiency. A 40-nm CMOS prototype achieves a Walden FoM of 1.5 fJ/conversion-step while operating at 100-kS/s from a 0.5-V supply. To further improve the energy-efficiency of the comparator, a novel dynamic pre-amp is proposed. By using an inverter-based input pair powered by a floating reservoir capacitor, the pre-amp realizes both current reuse and dynamic bias, thereby significantly boosting g [subscript m] /I [subscript D] and reducing noise. Moreover, it greatly reduces the influence of the input common-mode (CM) voltage on the comparator performance, including noise, offset, and delay. A prototype comparator in 180-nm achieves 46-μV input-referred noise while consuming only 1 pJ per comparison under 1.2-V supply, which represents greater than 7 times energy efficiency boost compared to that of a Strong-Arm (SA) latch. The second part of this dissertation focuses on high-speed data converter techniques. A 10-bit high-speed two-stage loop-unrolled SAR ADC is presented. To reduce the SAR logic delay and power, each bit uses a dedicated comparator to store its output and generate an asynchronous clock for the next comparison. To suppress the comparator offset mismatch induced non-linearity, a shared pre-amp are employed in the second fine stage, which is implemented by a dynamic latch to avoid static power consumption. The prototype ADC in 40-nm CMOS achieves 55-dB peak SNDR at 200-MS/s sampling rate without any calibration. A key limiting factor for the SAR ADC to simultaneously achieve high speed and high resolution is the reference ripple settling problem caused by DAC switching. Unlike prior techniques that aim to minimize the reference ripple which requires large reference buffer power or on-chip decoupling capacitance area, this work proposes a new perspective: it provides an extra path for the full-sized reference ripple to couple to the comparator but with an opposite polarity, so that the effect of the reference ripple is canceled out, thus ensuring an accurate conversion result. The prototype 10-bit 120-MS/s SAR ADC is fabricated in 40-nm CMOS process and achieves an SNDR of 55 dB with only 3 pF reference decoupling capacitor. Finally, this dissertation also presents the design of an incremental time-domain two-step CDC. Unlike the classic two-step CDC, this work replaces the OTA-based active-RC integrator with a VCO-based integrator and performs time domain (TD) ΔΣ modulation. The VCO is mostly digital and consumes low power. Featuring the infinite DC gain in phase domain and intrinsic spatial phase quantization, this TDΔΣ enables a CDC design, achieving 85-dB SQNR by having only a 4-bit quantizer, a 1st-order loop and a low OSR of 15. The prototype fabricated in 40-nm CMOS achieves a resolution of 0.29 fF while dissipating only 0.083 nJ per conversion, which improves the energy efficiency by greater than 2 times comparing to that of state-of-the-art CDCsElectrical and Computer Engineerin