Communication Subsystems for Emerging Wireless Technologies

The paper describes a multi-disciplinary design of modern communication systems. The design starts with the analysis of a system in order to define requirements on its individual components. The design exploits proper models of communication channels to adapt the systems to expected transmission conditions. Input filtering of signals both in the frequency domain and in the spatial domain is ensured by a properly designed antenna. Further signal processing (amplification and further filtering) is done by electronics circuits. Finally, signal processing techniques are applied to yield information about current properties of frequency spectrum and to distribute the transmission over free subcarrier channels

Paraunitary oversampled filter bank design for channel coding

Oversampled filter banks (OSFBs) have been considered for channel coding, since their redundancy can be utilised to permit the detection and correction of channel errors. In this paper, we propose an OSFB-based channel coder for a correlated additive Gaussian noise channel, of which the noise covariance matrix is assumed to be known. Based on a suitable factorisation of this matrix, we develop a design for the decoder's synthesis filter bank in order to minimise the noise power in the decoded signal, subject to admitting perfect reconstruction through paraunitarity of the filter bank. We demonstrate that this approach can lead to a significant reduction of the noise interference by exploiting both the correlation of the channel and the redundancy of the filter banks. Simulation results providing some insight into these mechanisms are provided

Performance evaluation of 5G millimeter-wave cellular access networks using a capacity-based network deployment tool

The next fifth generation (5G) of wireless communication networks comes with a set of new features to satisfy the demand of data-intensive applications: millimeter-wave frequencies, massive antenna arrays, beamforming, dense cells, and so forth. In this paper, we investigate the use of beamforming techniques through various architectures and evaluate the performance of 5G wireless access networks, using a capacity-based network deployment tool. This tool is proposed and applied to a realistic area in Ghent, Belgium, to simulate realistic 5G networks that respond to the instantaneous bit rate required by the active users. The results show that, with beamforming, 5G networks require almost 15% more base stations and 4 times less power to provide more capacity to the users and the same coverage performances, in comparison with the 4G reference network. Moreover, they are 3 times more energy efficient than the 4G network and the hybrid beamforming architecture appears to be a suitable architecture for beamforming to be considered when designing a 5G cellular network

Deep Space Network information system architecture study

The purpose of this article is to describe an architecture for the Deep Space Network (DSN) information system in the years 2000-2010 and to provide guidelines for its evolution during the 1990s. The study scope is defined to be from the front-end areas at the antennas to the end users (spacecraft teams, principal investigators, archival storage systems, and non-NASA partners). The architectural vision provides guidance for major DSN implementation efforts during the next decade. A strong motivation for the study is an expected dramatic improvement in information-systems technologies, such as the following: computer processing, automation technology (including knowledge-based systems), networking and data transport, software and hardware engineering, and human-interface technology. The proposed Ground Information System has the following major features: unified architecture from the front-end area to the end user; open-systems standards to achieve interoperability; DSN production of level 0 data; delivery of level 0 data from the Deep Space Communications Complex, if desired; dedicated telemetry processors for each receiver; security against unauthorized access and errors; and highly automated monitor and control

mmWave Massive MIMO with Simple RF and Appropriate DSP

There is considerable interest in the combined use of millimeter-wave (mmwave) frequencies and arrays of massive numbers of antennas (massive MIMO) for next-generation wireless communications systems. A symbiotic relationship exists between these two factors: mmwave frequencies allow for densely packed antenna arrays, and hence massive MIMO can be achieved with a small form factor; low per-antenna SNR and shadowing can be overcome with a large array gain; steering narrow beams or nulls with a large array is a good match for the line-of-sight (LOS) or near-LOS mmwave propagation environments, etc.. However, the cost and power consumption for standard implementations of massive MIMO arrays at mmwave frequencies is a significant drawback to rapid adoption and deployment. In this paper, we examine a number of possible approaches to reduce cost and power at both the basestation and user terminal, making up for it with signal processing and additional (cheap) antennas. These approaches include lowresolution Analog-to-Digital Converters (ADCs), wireless local oscillator distribution networks, spatial multiplexing and multistreaming instead of higher-order modulation etc.. We will examine the potential of these approaches in making mmwave massive MIMO a reality and discuss the requirements in terms of digital signal processing (DSP).Comment: published in Asilomar 201

Emerging applications of integrated optical microcombs for analogue RF and microwave photonic signal processing

We review new applications of integrated microcombs in RF and microwave photonic systems. We demonstrate a wide range of powerful functions including a photonic intensity high order and fractional differentiators, optical true time delays, advanced filters, RF channelizer and other functions, based on a Kerr optical comb generated by a compact integrated microring resonator, or microcomb. The microcomb is CMOS compatible and contains a large number of comb lines, which can serve as a high performance multiwavelength source for the transversal filter, thus greatly reduce the cost, size, and complexity of the system. The operation principle of these functions is theoretically analyzed, and experimental demonstrations are presented.Comment: 16 pages, 8 figures, 136 References. Photonics West 2018 invited paper, expanded version. arXiv admin note: substantial text overlap with arXiv:1710.00678, arXiv:1710.0861